Bang & Olufsen BeoLab 7-1 Bedienungsanleitung

Guide

BeoLab 7–1

WARNING: To prevent ﬁre or electric

shock, do not expose this appliance

to rain or moisture. Do not expose

this equipment to dripping or splash-

ing and ensure that no objects ﬁlled

with liquids, such as vases, are placed

on the equipment.

To completely disconnect this equip-

ment from the AC Mains, disconnect

the power supply cord plug from the

AC receptacle.

This symbol indicates that a

dangerous voltage constitut-

ing a risk of electric shock is

present within this unit.

This symbol indicates that there

are important operating and

maintenance instructions in the

literature accompanying this

unit.

CAUTION: To reduce the risk of

electric shock, do not remove

cover (or back).

No User-serviceable parts inside.

Refer servicing to qualified ser-

vice personnel.

Daily use

When you have ﬁnished setting

up the loudspeaker as described

on the following pages, connect

the entire system to the mains.

Loudspeaker protection

The loudspeaker is equipped with a

thermal protection system which

prevents damage from overheating.

If an error occurs – or the speaker

units become overheated – the

system automatically switches the

loudspeaker to standby.

To restore the sound:

> Disconnect the loudspeaker from

the mains.

> Allow the system time to reset

or cool down (approximately

3–5 minutes).

> Reconnect the loudspeaker to

the mains.

Should the problem persist, contact

your Bang & Olufsen retailer.

Cleaning the loudspeaker

Clean dusty surfaces using a dry,

soft cloth. If necessary, remove

grease stains or persistent dirt with

a lint-free, ﬁrmly wrung cloth, dipped

in a solution of water containing

only a few drops of mild detergent,

such as washing-up liquid.

The loudspeaker front grill may be

cleaned with a vacuum cleaner with

a soft brush nozzle, and set to the

lowest level.

Never use alcohol or other solvents to

clean any parts of the loudspeaker!

Switching on and off

When you switch on your Bang &

Olufsen system, the loudspeaker

switches on simultaneously, and

when you switch the system

off again the loudspeaker also

switches off.

NOTE! Prolonged listening at high

volume levels may cause hearing

damages.

Set up the loudspeaker

We recommend that you follow

this procedure:

– Disconnect your Bang & Olufsen

system from the mains.

– Place the loudspeaker according

to the guidelines on this page.

– Use the enclosed accessories to

mount the loudspeaker to the

BeoVision stand or wall bracket

as explained on the next page.

– Connect the loudspeaker as

explained in ‘Cable connections’

(pp. 6–7).

– Set the POSITION switch to the

correct setting. This is explained

in ‘Adapt the loudspeaker to your

room’ (pp. 8–9).

– Connect the entire system to the

mains again.

Cautions

– Make sure that the loudspeaker

is placed and connected in

accordance with the instructions

in this Guide.

– The loudspeaker must be fastened

to the enclosed bracket and on a

suitable Bang & Olufsen stand or

wall bracket.

– Do not attempt to open the loud-

speaker. Leave such operations to

qualiﬁed service personnel!

– The loudspeaker is designed for

indoor use in dry, domestic

environments only, and for use

within a temperature range of

10–40º C (50–105º F).

– In order not to block the sound

emitting from the rear bass

reﬂex ports and the bass units

on the bottom, leave a minimum

of 6 cm (2½") free space behind

and below the loudspeaker.

– Always place the loudspeaker in

a horisontal position.

– Do not place any items on top of

the loudspeaker.

To attach the loudspeaker

front grill

Do not mount the front grill upside

down (marked on the rear by ):

> Place the grill on the front of the

loudspeaker shifted approximately

10 mm (½") to the left.

> Push the grill to the right (make

sure that all ﬁve ‘attach-points’

engage with the corresponding

brackets on the loudspeaker).

d d

On this page is shown how to

fasten the loudspeaker to a

BeoVision 7* stand or wall

bracket. If you wish to use

the loudspeaker with another

Bang & Olufsen system, refer

to the Guide enclosed with

the system.

aRemove the small cover on the

stand (there is no cover on the

wall brackets). Press the cover

as shown, and it will come loose.

bFasten the bracket to the stand or

wall bracket. Use the two longest

screws (M5 × 25 mm).

cFasten the loudspeaker to the

bracket. Use the two shortest

screws (M5 × 8 mm). However, do

not fully tighten the screws before

you have made the adjustments

mentioned below (d).

Adjustments: First, make sure that

the television is adjusted to a level

position on its stand or wall

bracket. Then use the two screws

(d) to adjust the loudspeaker so

that it is parallel to the lower edge

of the television. Align the

loudspeaker front with the

television and tighten the two

screws (c).

*NOTE! BeoVision 7 and its

accessories are not available

on all markets.

Cable connections

The loudspeaker is primarily

intended to be used in a setup

with BeoVision 7*. It may,

however, be used with other

Bang & Olufsen systems as well.

If used in a setup not including

BeoVision 7, you will require

a mains cord and a Power Link

cable. These cables are available

as optional accessories from your

Bang & Olufsen retailer.

Mains connections

The loudspeaker has two sockets

concerning mains supply.

The socket marked ~is for mains

supply input (connection from the

wall outlet), and the other is a mains

supply output to the television.

Note: The mains cord from the wall

outlet must be fastened to the cable

clamp on the loudspeaker – as shown

on the next page.

POSITION switch

This switch has two settings: F

(Free-standing position) and W

(Wall position).

Which setting to use is explained

in ‘Adapt the loudspeaker to your

room’ (pp. 8–9).

POWER LINK socket

Use this socket to connect the

loudspeaker to one of the Power

Link sockets on the Bang & Olufsen

system – see the next page.

The socket panel is located on the rear of the loudspeaker.

*NOTE! BeoVision 7 and its

accessories are not available

on all markets.

Mains connection

to the television

POSITION switch

Cable clamp

POWER LINK

socket

Power Link

Mk 3

The two mains cords and the

Power Link cable are enclosed

with BeoVision 7.

Cable clamp: For safety reasons,

the mains cord from the wall outlet

must be secured to the loudspeaker.

To do so, tug the cord behind the

clamp.

Power Link cable: Do not use a

cable of the older type, as this

will cause noise, and therefore

not give optimum sound quality!

The new type has a triangular

mark on the plug.

Connection to BeoVision 7…

Connect the loudspeaker to one of

the Power Link sockets on the left

BeoVision 7 socket panel.

For further information about the

BeoVision 7 socket panels, refer

to the Guides enclosed with the

product.

Connection to other

Bang & Olufsen systems…

Use a Power Link cable of the

correct type to connect the loud-

speaker to a Power Link socket on

the Bang & Olufsen system.

For further information, refer to the

Guide enclosed with the system.

BeoVision 7

BeoLab 7–1

Adapt the loudspeaker to your room

When a loudspeaker is placed in

a corner or close to a wall, the

bass level is boosted compared to

the bass level from a loudspeaker

placed in a more free-standing

position.

To remove this excessive bass

boost, use the POSITION switch

to ensure that the bass level suits

the placement of the loudspeaker.

The appropriate switch setting

depends on the distance from

the loudspeaker to the walls and

corners of the room.

The POSITION switch

The POSITION switch has two

settings – F and W:

• F(Free-standing position)

Use this setting if the loudspeaker is

placed so that the front grill is more

than 50 cm (20") from the rear wall,

for example on the Floor Stand, on

the Motorised Table Stand, or on

the Table Stand.

• W(Wall position)

Use this setting if the loudspeaker

is placed so that the front grill is less

than 50 cm (20") from the rear wall.

Always use this setting if the

loudspeaker is placed on any of the

wall brackets, but also when placed

on the stands mentioned above –

close to the rear wall.

The POSITION switch is located on

the socket panel.

How to measure… The distance

is measured as shown here – the

loudspeaker seen from above.

Setup examples

The three examples to the left all

show the loudspeaker placed more

than 50 cm (20") from the rear wall

– and therefore the POSITION switch

should be set to F.

The four examples to the right all

show the loudspeaker placed closer

than 50 cm (20") from the rear wall

– and therefore the POSITION switch

should be set to W.

If the loudspeaker is ﬁtted to either

the Motorised Table Stand or the

Table Stand – and you have chosen

to place it on the ﬂoor – you should

set the POSITION switch to W.

NOTE! BeoVision 7 and the

accessories shown in the examples,

are not available on all markets!

Andere Handbücher für BeoLab 7-1

Inhaltsverzeichnis

Andere Bang & Olufsen Sprecher Handbücher

Bang & Olufsen

Bang & Olufsen BeoLab 4 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beovox S35 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 12-3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 35 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 18 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 35 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beolit 12 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 5 6881 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-4 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 2 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 19 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beoplay M5 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 2500 Kurzanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 1 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEOPLAY A2 ACTIVE Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 3 6881 Service-Handbuch

Bang & Olufsen

Bang & Olufsen BEOLAB 28 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoSound 3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 7-4 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beosound Explore Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoPlay S3 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab 10 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BeoLab Penta Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung