Bante Instruments SALscan10 Bedienungsanleitung

SALscan10/20 Pocket Salinity Tester

USER MANUAL

Bante Instruments Inc.

1 ISALscan10/20

Overview

Thank you for selecting the SALscan series pocket salinity tester. This

user manual provides a step-by-step guide to help you operate the

tester, please carefully read the following instructions before use.

Installing the Batteries

1. Twist the electrode collar counter clockwise, pull the electrode

away from the tester.

2. Insert two AAA alkaline batteries into the battery compartment,

note polarity.

3. Push the electrode into the tester and twist the electrode collar

clockwise until tight.

Keypad

Key

Function

•Switch the tester on or off

•Lock or unlock measurement

•Exit the calibration, settings and return to the

salinity measurement

•Start calibration

•Press and hold the key to enter the setup menu

•Select an option

•Confirm the calibration, settings or displayed option

•Toggle between salinity and conductivity

measurement modes

Display

Icon

Description

When the battery voltage falls below the minimum

power requirements, the icon automatically

disappears

MEAS

Indicates that the tester is in the measurement mode

CAL

Indicates that the tester is in the calibration mode

SETUP

Indicates that the tester is in the setup mode

ATC

Indicates that the automatic temperature compensation

is enabled

Prior to Use

Remove the protective cap and translucent cover from the bottom of

the tester. If the platinum sensor has dried out, soak the electrode for

about 10 minutes in tap water.

Switching the Tester On and Off

•Press and hold the Meas key for about 5 seconds to switch on

the tester.

•Press and hold the Meas key to switch off the tester.

If you do not press any key within 8 minutes, the tester will switch off

automatically to conserve energy.

Tap water

SALscan10/20 I2

Setup Menu

The SALscan series tester contains 6 menu items in the setup menu,

the following table describes the functions of each option.

Menu Item

Option and Description

Calibration Points

Set the number of calibration points.

1 point (default)

2 points

3 points

Measurement Unit

Set the default temperature unit.

Degrees Celsius (default)

Degrees Fahrenheit

Temperature Calibration

Refer to page 3.

Range: 0 to 100°C

Range: 0 to 210°F

Auto-Hold

If enabled, the tester will automatically sense and

lock the measurement endpoint.

Enable

Disable (default)

Auto-Power Off

If enabled, the tester will automatically switch off

if no key is pressed within 8 minutes.

Enable (default)

Disable

Factory Reset

If enabled, all of the calibration values and current

settings will be deleted or reset to the factory

defaults, the tester must be recalibrated.

Enable

Disable (default)

Setting the Default Option

1. In the measurement mode, press and hold the Cal key to enter

the setup menu.

2. If necessary, press the Cal key again to select an option.

3. Press the Enter key, the tester saves the current option and moves

to the next menu item.

4. Repeat steps above until the tester returns to the measurement

mode.

•During the setting process, if you do not need to calibrate the

temperature, press the Enter key to skip the /or /

option.

•To exit the setup menu, press the Meas key.

Conductivity Calibration

The SALscan series tester allows up to 3 points calibration. For better

accuracy, we recommend that you perform 3 points calibration or

select a standard solution closest to the sample conductivity you are

measuring. The tester will automatically detect the calibration standard

and prompt the user to perform the calibration. When the calibration

is completed, all new calibration values will override existing data.The

following table shows acceptable standard solutions for each tester.

SALscan10

Measurement Range

Standard Solution Range

Default

0 to 200 µS/cm

70 to 170 µS/cm

84 µS/cm

200 to 2000 µS/cm

700 to 1700 µS/cm

1413 µS/cm

2 to 20 mS/cm

7 to 17 mS/cm

12.88 mS/cm

Option

Menu item

3 ISALscan10/20

SALscan20

Measurement Range

Standard Solution Range

Default

200 to 2000 µS/cm

700 to 1700 µS/cm

1413 µS/cm

2 to 20 mS/cm

7 to 17 mS/cm

12.88 mS/cm

20 to 200 mS/cm

70 to 170 mS/cm

111.8 mS/cm

Make sure that using the fresh standard solution during the calibration.

DO NOT reuse the standard solution after calibration, contaminants

in solution will affect the calibration and eventually the accuracy of

the measurement.

Single Point Calibration

Ensure that you have selected 1 point calibration in the setup menu.

1.1 Press the Cal key, the tester shows ----/CAL 1.

1.2 Rinse the electrode with distilled water and place into the

standard solution. Stir tester gently to remove air bubbles trapped.

in the slot of the sensor. The tester will automatically recognize.

the standard solution and show the calibration value.

1.3 Press the Enter key, the default calibration value begins flashing.

1.4 If necessary, press the Cal key to modify the calibration value,

press the Enter key to confirm and move to the next digit. When

the setting is completed, make sure that the displayed value

matches the calibration standard.

1.5 Press the Enter key, the tester begins the calibration. When the

reading has stabilized, the display will show . Calibration

is completed.

Multipoint Calibration

Ensure that you have selected 2 or 3 points calibration in the setup

menu.

2.1 Repeat steps 1.1 through 1.5 above. When the first calibration

point is completed, the display will show ----/CAL 2, the tester

prompts you to continue with second point calibration.

2.2 Repeat steps 1.2 through1.5 above until the display shows .

Calibration is completed.

•Performing the conductivity calibration will simultaneously

calibrate the corresponding salinity value.

•To exit the calibration without saving calibrated values, press the

Meas key.

Temperature Calibration

The SALscan series tester is installed with a built-in temperature sensor

for automatic temperature compensation. During the measurement,

if the measured temperature reading differs from that of an accurate

thermometer, the tester needs to be calibrated.

1. Press and hold the Cal key to enter the setup menu.

2. Press the Enter key until the display shows /or /.

3. Press the Cal key, the tester enters the temperature calibration

mode.

SALscan10/20 I4

4. Place the electrode into a solution with a known accurate

temperature and wait for the measurement to stabilize.

5. Press the Cal key to modify the temperature value.

6. Press the Enter key to save and press the Meas key to return

to the measurement mode.

Measurement

Switching the Measurement Mode

Press the Enter key, the tester will show (conductivity),

(salinity) and switch to the corresponding measurement mode

automatically.

Measuring the Sample

Rinse the electrode with distilled water, place the electrode into the

sample solution and stir gently, make sure that no air bubbles on the

sensor surface. Wait for the measurement to stabilize and record the

reading.

•During the measurement, DO NOT completely immerse the tester

in water.

•If the display shows ---- indicating the measurement exceeds the

range, remove the tester from the sample immediately.

•If the option is enabled in the setup menu, the tester will

automatically lock the measurement endpoint and show HOLD

icon. Press the Meas key to resume measuring.

Electrode

Maintenance and Replacement

•Rinse the electrode thoroughly with distilled water after use.

•Do not touch the platinum black coating on the sensor surface

and always keep it clean.

•If there is a build-up of solids inside the sensor, remove carefully,

then recalibrate the tester.

•If you do not use the tester for long periods, store the electrode

with tap water.

Platinum sensor

5 ISALscan10/20

Replacing the Electrode

If the tester fails to calibrate or gives fluctuating readings, you should

consider replacing the electrode.

1. Twist the electrode collar counter clockwise, pull the electrode

away from the tester.

2. Align the slot on the new electrode, gently push the electrode

into the tester.

3. Twist the electrode collar clockwise until tight.

Appendix

Preparation of Conductivity Standard Solutions

Place the analytical grade potassium chloride (KCl) in a beaker and

dry in an oven for about 3 hours at 105°C (221°F), then cool to room

temperature. Add the reagent to a 1 liter volumetric flask according

to the instructions in table below.

Conductivity Standard

Reagent

Weight

84 µS/cm

KCl

42.35 mg

1413 µS/cm

KCl

745.5 mg

12.88 mS/cm

KCl

7.45 g

111.8 mS/cm

KCl

74.5 g

Fill the distilled water to the mark, mix the solution until the reagent

is completely dissolved.

Optional Accessories

Order Code

Description

E-ECscan-C1-10K

For SALscan10 tester, cell constant K=1,

measuring range 10 to 20 mS/cm

E-ECscan-C10-10K

For SALscan20 tester, cell constant K=10,

measuring range 0.1 to 200 mS/cm

ECCS-84

Standard solution 84 μS/cm, 480 ml

ECCS-1413

Standard solution 1413 μS/cm, 480 ml

ECCS-1288

Standard solution 12.88 mS/cm, 480 ml

ECCS-50

Standard solution 50 mS/cm, 480 ml

ECCS-1118

Standard solution 111.8 mS/cm, 480 ml

Tester Specifications

Model

SALscan10

SALscan20

Conductivity

Range

0 to 20 mS/cm

0 to 200 mS/cm

Resolution

0.01, 0.1, 1

Accuracy

±1% F.S.

Calibration Points

1 to 3 points

Calibration Solutions

84 μS/cm

1413 μS/cm

12.88 mS/cm

1413 μS/cm

12.88 mS/cm

111.8 mS/cm

Salinity

Range

0 to 10 ppt

0 to 80 ppt

Resolution

0.01

Accuracy

±1% F.S.

Temperature

Range

0 to 60°C (32 to 140°F)

Resolution

0.1°C (0.1°F)

Accuracy

±1°C (±1.8°F)

Calibration Point

1 point

Calibration Range

Reading ±10°C/°F

Other Specifications

Temperature Compensation

0 to 60°C (32 to 140°F), automatic

Temperature Coefficient

2%/°C

Reference Temperature

25°C

Cell Constant

K=1

K=10

Operating Temperature

0 to 50°C (32 to 122°F)

Storage Temperature

0 to 60°C (32 to 140°F)

Relative Humidity

< 80% (non-condensing)

IP Rating

IP54

Display

LCD, 21 × 21 mm (0.82 × 0.82 in.)

Power Requirements

2 × 1.5V AAA alkaline batteries

Auto-Off

8 minutes after last key pressed

Dimensions

185 (L) ×40 (Dia.) mm (7.28 ×1.57 in.)

Weight

100g (3.5 oz.)

The information in this document is subject to change without notice.

Disposal

This product is required to comply with the European Union’s Waste

Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC and

may not be disposed of in domestic waste. Please dispose of product

in accordance with local regulations at the collecting point specified

for electrical and electronic equipment.

Warranty

The warranty period for tester is one year from the date of shipment.

Above warranty does not cover the electrode and standard solutions.

Out of warranty products will be repaired on a charged basis.

The warranty on your tester shall not apply to defects resulting from:

•Improper or inadequate maintenance by customer

•Unauthorized modification or misuse

•Operation outside of the environment specifications of the

products.

For more information, please contact the supplier.

Office: 4715 Castlewood St., Sugar land, TX 77479, USA

Tel: (+1) 346-762-7358

E-mail: [email protected]

Factory: F3, Building 2, No.2185, Laifang Rd., Shanghai 201615, China

Tel: (+86) 21-6404-1598

E-mail: banteinstrument@hotmail.com

www.bante-china.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bante Instruments Messgerät Handbücher

Bante Instruments

Bante Instruments 9 Series Bedienungsanleitung

Bante Instruments

Bante Instruments Bante900P Bedienungsanleitung

Bante Instruments

Bante Instruments Bante810 Bedienungsanleitung

Bante Instruments

Bante Instruments POL-200 Bedienungsanleitung

Bante Instruments

Bante Instruments DDS-12DW Bedienungsanleitung

Bante Instruments

Bante Instruments TB100 Bedienungsanleitung

Bante Instruments

Bante Instruments 820 Bedienungsanleitung

Bante Instruments

Bante Instruments A Series Bedienungsanleitung

Bante Instruments

Bante Instruments 220 Bedienungsanleitung

Bante Instruments

Bante Instruments TB100 Bedienungsanleitung

Bante Instruments

Bante Instruments 904P Bedienungsanleitung

Bante Instruments

Bante Instruments PHscan10 Bedienungsanleitung

Bante Instruments

Bante Instruments PHscan10 Bedienungsanleitung

Bante Instruments

Bante Instruments 221 Bedienungsanleitung

Bante Instruments

Bante Instruments 810 Bedienungsanleitung

Bante Instruments

Bante Instruments 320 Bedienungsanleitung

Bante Instruments

Bante Instruments TB200 Bedienungsanleitung

Bante Instruments

Bante Instruments Bante221 Bedienungsanleitung

Bante Instruments

Bante Instruments PHscan20 Bedienungsanleitung

Bante Instruments

Bante Instruments DDS-12DW Bedienungsanleitung

Bante Instruments

Bante Instruments TDSscan20 Bedienungsanleitung

Bante Instruments

Bante Instruments TB100 Bedienungsanleitung

Bante Instruments

Bante Instruments 210 Bedienungsanleitung

Bante Instruments

Bante Instruments TB200 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung