Barco R817211K Bedienungsanleitung
BARCO PROJECTION SYSTEMS
Date :
151101
INSTALLATION MANUAL
KIT ANALYSER FOR 6500/6400I, RSIM6(HB/HBMLA/LL) & HELIOS PROJECTORS
R817211K R8172112K
R820349K R8172122K
R8172121K R817214K
R821060K R8172132K
Art. No. :
R5976207
Rev :
01
ANALYSER
6500 Kit
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, November 2001.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO n.v./Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : +32/56/368211
Fax : +32/56/351651
Visite Barco at the web : http://www.barco.com
Printed in Belgium
BARCO 3 Projection Systems
Safety
Who This procedure is intended for use only by qualified service technicians who have been
trained and authorized by BARCO !
Hot Surface Switch the projector to stand by and let it cool down for at least 15 minutes before
starting with the Analyser replacement.
Risk of Electrical
Shock
Power down the projector and unplug the power cord from the wall outlet.
Once the projector is cooled down and the power is off, continue with the replacement
procedure.
Antistatic
Protection Steps
Wear a wrist band which is connected to the ground while handling the static sensitive
parts.
Sensitive Device LCD panels are very sensitive devices. Observe full precautions for handling electro-
static devices. Do not touch the glass surface. Hold only by the surrounding metal
parts.
BARCO 4 Projection Systems
Contents of the Kit
Type The kit contains one analyser depending on the color. As the built-in procedure is the
same for red, green or blue, the installation instructions will only be explained once.
Part Listing The kit contains one analyser depending on the color :
R817211 or
R8172112
or
R820349 or
R8172122
or
R8172121 or
R817214
or
R821060 or
R8172132
and
R5976207
1
1
1
1
1
Analyser red
Analyser green
Analyser green for SSS cube
Analyser blue
Manual ins analyser 6500/RSIM6 & Helios
Part Number Description Qty
Antistatic
Protection Steps
Wear a wrist band which is connected to the ground while handling the static sensitive
parts.
Analyser Kits &
Where used
Analyser Red:
R817211K
Analyser Green:
R820349K
Analyser Gr SSS:
R8172121K
Analyser Bleu:
R821060K
Analyser Red:
R8172112K
Analyser Green:
R8172122K
Analyser Gr SSS:
R817214K
Analyser Bleu:
R8172132K
Where used
6300/6400 6500/6400i SIM6 SIM6MLA SIM6HB SIM6HB MLA SIM6LL HELIOS
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
Kit number
BARCO 5 Projection Systems
Access to the LCD+X-cube
Necessary Tools Screwdriver 8 mm.
Removing the
Lens
To remove the lens, follow the next procedure:
1
2
3
4
1
2
2
Open the lens cover by pivoting it backwards and hook it
of.
Loosen the fixation screws of the motor part and pivote it
upwards.
Open both lens locks by pulling them backwards.
Take the lens out of the lens house.
Step Action Image
To be continued on next page.
Necessary Parts None
Illustrations on
Removing the
Lens
Image 2
Image 1
Lens lockings
Motor part
Fixation screws
What has to be
done
The lens has to be removed and the top cover has to be opened.
For projectors with a black cover it is not necessary to remove the lens, remove only
the top cover (see next page).
BARCO 6 Projection Systems
Access to the LCD + X-cube (Continued)
Removing the
Top Cover
1
2
3
1
2
Pull the 3 rubber sealing pieces.
Turn out the 3 fixing screws.
Take off the top cover.
Step Action Image
To remove the top cover, follow the next procedure:
Illustrations on
Top Cover
Removal
Image 1
Image 2
BARCO 7 Projection Systems
Removing the EMC Plate (when present).
Image 2
$
What has to be
done
The EMC plate covering the Pixel Map Processor has to be removed.
Necessary Tools Philips screwdriver
Necessary Parts None
1
2
3
4
5
1
1
2
Begin with unscrewing the screw B retaining the elecrical
conductor.
Turn out the screws retaining the little plate A
Remove the little plate
Turn carefuly the remaining screws out , be aware not to
drop these screws into the apparatus.
Remove the EMC plate
Step Action Image
Removing the
plate
Illustrations
Image 1
BARCO 8 Projection Systems
Removing the LCD + X-CUBE Assembly
What has to be
done
The LCD + X-Cube assembly has to be removed out of the projector.
Necessary Tools Philips screwdriver
Electrical
disconnection of
the X-Cube.
Before removing the X-Cube, it must be electrically disconnected from the driver board.
Follow the next procedure:
1
2
Press very carefully on both sides of the
indicated points to unlock.
Pull out the cable.
Step Action Illustration
Press to lock
Press to unlock
Connector connector
cable
Necessary Parts None
Removing the X-
Cube Adjustment
Unit
To remove the LCD + X-cube unit together with the adjustment unit, follow the next
procedure:
1
2
3
1
1
Unplug the power cable.
Loosen both fixing screws down under by inserting Philips
screwdriver with a shaft of minimum 150 mm.
Slide out the assembly very carefully.
Step Action Image
Illustration
Cable connectors
Power cable
BARCO 9 Projection Systems
Disassembling the LCD + X-CUBE Assembly
What has to be
done
The LCD + X-Cube assembly has to be disassembled.
Necessary Tools Screwdriver 8 mm.
Nutdriver 5.5
Philips screwdriver
Electrical
disconnection of
the X-Cube.
Before disassembling the X-Cube assembly, it must be electrically disconnected from
the adjustment board. Follow the next procedure:
1
2
Press very carefully on both sides of the
indicated points to unlock.
Pull out the cable (see image 1).
Step Action Illustration
Press to lock
Press to unlock
Connector connector
cable
Necessary Parts None
Tip While removing the screws and the parts, put them on a row to find them back the
correct assembling order.
To be continued on next page.
Illustration
BARCO 10 Projection Systems
Disassembling the LCD + X-CUBE Assembly (Continued)
Illustration
Image 1
Image 2
Image 3
Disassembling
the X-cube
Assembly
To disassemble the X-cube assembly, follow the next procedure:
1
2
3
4
1
2
2
3
Turn out the 4 fixing screws with Philips screwdriver.
Take off the unit.
Turn out the 4 fixing screws with a nutdriver 5.5 o flat
screwdriver
Take off the metal holder
Step Action Image
Dieses Handbuch passt für folgende Modelle
7
Andere Barco Projektorzubehör Handbücher
Barco
Barco ClickShare CS-100 Bedienungsanleitung
Barco
Barco RLD (3.0-4.5:1) Bedienungsanleitung
Barco
Barco BarcoReality 909 Split Pack R9040040 Bedienungsanleitung
Barco
Barco OverView OVL708 Bedienungsanleitung
Barco
Barco CX-50 Gen2 Bedienungsanleitung
Barco
Barco WePresent WiPG-1000 Bedienungsanleitung
Barco
Barco ICMP HDD Bedienungsanleitung
Barco
Barco R9829335 Merkblatt
Barco
Barco QGD(7:1) R9840030 Bedienungsanleitung
Barco
Barco R9861510EU Bedienungsanleitung
Barco
Barco R762120 Bedienungsanleitung
Barco
Barco ClickShare Allgemeine Anweisungen
Barco
Barco F50 Betriebsanleitung
Barco
Barco R9827880 Bedienungsanleitung
Barco
Barco Lamp House with 2.5 kW lamp Bedienungsanleitung
Barco
Barco R9861520NA Bedienungsanleitung
Barco
Barco wePresent WiPG-1600W Bedienungsanleitung
Barco
Barco R812302K Bedienungsanleitung
Barco
Barco Event Master E2 Bedienungsanleitung
Barco
Barco R9841770 Bedienungsanleitung
