BARRON Exitronix CRL Series Bedienungsanleitung

CRL SERIES

INSTALLATION INSTRUCTIONS

10070166 Rev 4 - 04/19 1

INSTALLATION AND OPERATION INSTRUCTIONS

1. Loosen all (4) ceiling bracket wing nuts half way for ease of installation. Hang fixture on ceiling T-bars using the

ceiling brackets. (Fig. 1)

2. Tighten all ceiling bracket wing nuts to secure fixture in place. Adjust slot placement of ceiling brackets accordingly to

adjust enclosure opening to be level with the inside surface of the T-bar. (Fig. 2a, 2b)

a. Additional chains or cabling shall be used for enclosure securement. (Fig. 2)

3. Remove (4) #6-32 x 3/4” flat head screws from cover. (Fig. 3)

Fig. 1

Fig. 3

Wing Nuts

Bracket

6-32 x 3/4” flat

head screws

Fig. 2a

Fig. 2b

800.533.3948 • www.barronltg.com

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

When using electrical equipment, basic safety precautions should always be followed including the following:

• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.

• Installation and servicing of this equipment should be performed by qualified service personnel only.

• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations if applicable.

• Do not mount near gas or electrical heaters.

• Do not use outdoors.

• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by

unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

• Any modification or use of non-original components will void the warranty and product liability.

• Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS!

INSTALLATION INSTRUCTIONS

10070166 Rev 4 - 04/19 2

Fig. 4a

Fig. 4b

Lanyard Hook

Lanyard

4. Remove cover and connect lanyards to lanyard hooks found

inside enclosure. (Fig. 4a, 4b)

5. Connect flexible conduit to one of the three available conduit

knockouts. (Fig. 5)

6. Remove transformer compartment cover. Electrical

Connections should be made in transformer

compartment. Cap unused primary wire to prevent

shorting. (Fig. 6)

120V AC

White - Common

Black - 120V

Green - Ground

277V AC

White - Common

Orange - 277V

Green - Ground

7. Replace compartment cover and secure in place with (1) #6-32 x 1/4” pan head screw.

8. Verify connections are in place such as lamps, led, and test button.

9. Replace enclosure cover and secure in place with cover screws.

10. Open battery door by unscrewing captive thumb screw.

11. Connect battery and close battery door.

12. Secure in place by retightening thumb screw. (Fig. 7)

13. Cut ceiling tile to correct size as needed. (Fig. 8)

Fig. 5 Fig. 6

Fig. 7

Flexible

Conduit transformer

compartment

cover

#6 x 1/4” pan

head screw

Battery

Door

Battery

Connector

Led Indicator

Test Button

Fig. 8

CRL SERIES

800.533.3948 • www.barronltg.com

INSTALLATION INSTRUCTIONS

10070166 Rev 4 - 04/19 3

SELF-TEST/SELF-DIAGNOSTIC

OPERATING INSTRUCTIONS

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Installation

I M P O R T A N T: ONCE ALL EMERGENCY LAMPS HAVE BEEN CONNECTED TO THE UNIT EQUIPMENT, APPLY

NORMAL AC POWER AND CHARGE FOR 24 HOURS.

Operation

The purpose of this option is to provide self-testing and self-diagnostic capabilities to the unit equipment. At

predetermined intervals, the unit equipment will automatically switch into battery mode. The unit equipment will also

perform various self-diagnostic tests of the unit. Visual signaling will alert maintenance personnel to a fault of the unit

equipment electronics, emergency lamp(s), battery and/or battery charger. The circuitry continuously monitors the

operating condition of the unit equipment and battery charging circuit/battery supply voltage. Refer to table 1 for units

equipped with a tri-color LED indicator. Refer to table 2 for units equipped with a numeric indicator.

Self Test Features

• The unit equipment will automatically switch to battery mode every 28 days for a period of 1 minutes.

• The unit equipment will automatically switch to battery mode every 6 months for a period of 90 minutes.

Manual Test Features

• Press the TEST BUTTON momentarily for a 2 second test. (Tri-Color LED unit only)

• Press the TEST BUTTON until the LED turns ORANGE or Numeric display shows “7” for a manual 1 minute test.

• Press the TEST BUTTON until the LED flashes RED/GREEN, (Tri-Color LED unit only) for manual 90 minute test.

LED Indication

Steady

Pulse

Steady

Pulse

Steady

Pulse

LED Color

Green

Red

Orange

Red/Green

Unit Condition

Float Charge

Hi-Rate Charge

Low Batt Voltage

Emer Lamp Failure

No AC Power

Charge Failure

1 Minute Test

Batt Disconnected

90 Minute Test

Comment

Batt Fully Charged

Batt Under High-Rate Charge

Replace Battery

Check AC Connection

Replace Transformer

1 Min Test Every 28 Days

Check Batt Connections

90 Min Test Every 6 Months

Replace Damaged or

Missing Lamps

Table 1 - Tri-color LED Indicator

CHARGED 0 Float charging

CHARGING 1 Hi rate charging

EM/BATT 2 Discharging

CHRG FAIL 3 Charger failure

DISC BATT 4 Battery not connected

LAMP FAIL 5 Lamp failure

LOW BATT 6 Low battery voltage

1 MIN TEST 7 Manual testing

90 MIN TEST 8 Self testing

STATUS LEDGE Condition

Table 2 - Numeric Indicator

Numeric Display

Tri-Color LED

CRL SERIES

800.533.3948 • www.barronltg.com

Inhaltsverzeichnis

Andere BARRON Beleuchtungsausrüstung Handbücher

BARRON

BARRON TRACE-LITE AXL2 Bedienungsanleitung

BARRON

BARRON Exitronix NFT Series Bedienungsanleitung

BARRON

BARRON TL301 Bedienungsanleitung

BARRON

BARRON EXITRONIX CRL Series Bedienungsanleitung

BARRON

BARRON Exitronix VEX-8 NEMA Bedienungsanleitung

BARRON

BARRON TRACE-LITE RHL-ACR Bedienungsanleitung

BARRON

BARRON specialtyLED FTK Bedienungsanleitung

BARRON

BARRON GROWLITE GRM Bedienungsanleitung

BARRON

BARRON EXITRONIX VLED-90L Series Bedienungsanleitung

BARRON

BARRON TRACE-LITE WTA Series Bedienungsanleitung

BARRON

BARRON Exitronix LED-90 Series Bedienungsanleitung

BARRON

BARRON Exitronix S900C Series Bedienungsanleitung

BARRON

BARRON EXITRONIX LED-51 Series Bedienungsanleitung

BARRON

BARRON Trace-Lite E110 Bedienungsanleitung

BARRON

BARRON EXITRONIX 82 Series Bedienungsanleitung

BARRON

BARRON EXITRONIX ILX Series Bedienungsanleitung

BARRON

BARRON EXITRONIX 400WX Series Bedienungsanleitung

BARRON

BARRON Exitronix 400U Series Bedienungsanleitung

BARRON

BARRON Speciality LED FBTCJ-24V Bedienungsanleitung

BARRON

BARRON Exitronix TPXC Series Bedienungsanleitung

BARRON

BARRON EXITRONIX SCL Series Bedienungsanleitung

BARRON

BARRON Trace-Lite AXL2 Bedienungsanleitung

BARRON

BARRON Growlite GLB-315-A-120/277 Bedienungsanleitung

BARRON

BARRON TRACE-LITE TL101 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung