Bartec Tech500 Bedienungsanleitung
Tech 500 User Guide rev1.0 JUNE 2013
1
TABLE OF CONTENTS
IMPORTANT NOTICES 2
BEFORE YOU GET STARTED 3
TOOL LAYOUT 4
TOOL CONNECTIONS 5
POWER ON/OFF 6
CHARGING TOOL 7
TOOL DISPLAY AND ICONS 8
MENU SYSTEM
TEST BEFORE YOU TOUCH
RELEARN
REVIEW DATA
TOOLKIT
MY TOOL 11
TOOL POSITIONING/READING A SENSOR 20
UPDATING YOUR TOOL (PC) 29
UPDATING YOUR TOOL (SD Card) 32
UPDATING YOUR TOOL (Wireless)
APPENDIX A: INDUCTIVE CHARGING
APPENDIX B: VIN 37
APPENDIX C: FAQ’S & TROUBLESHOOTING GUIDE 38
APPENDIX D: DEFINITIONS 39
APPENDIX E: TPMS SYSTEM REVIEW 40
APPENDIX F: COMS ERROR TROUBLESHOOTING 42
APPENDIX G: Technical Support 43
LIMITED WARRANTY 44
TOOL REGISTRATION 47
Tech 500 User Guide rev1.0 JUNE 2013
2
INCLUDED IN Tech500 KIT:
Tech500 TPMS Tool [with protective Boot]
SD Card [in the tool]
Power Supply
Re-Learn Magnet
USB Cable
DB15 to OBDII Cable
Tech500 Quick Start Guide
Tech500 User Guide
Kit CD
IMPORTANT NOTICES
All specifications, illustrations and information contained within this manual are based on the
most current information available at the time of publication. BartecUSA reserves the right to
make changes at any time without obligation to notify any person or organization. BartecUSA
will do its best to keep you the customer informed of any changes that might affect the tools
performance.
FCC Compliance Model: DSW
FCC ID: SX8T500 IC: 5736A-T500
Contains FCC ID: QOQWT12 IC: 5123A-BGTWT12A
Contains FCCID: YOPGS1011MIP IC: 9154A-GS1011MIP
This device complies with Part 15 of the FCC Rules and with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
Tech 500 User Guide rev1.0 JUNE 2013
3
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
Note: Changes or modifications not expressively approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at their expense.
BEFORE YOU GET STARTED
Before you get started using your Tech500 TPMS tool, there are a few items to review.
Charge your tool
The Tech500 is shipped with a fully charged battery, but due to shelf drain it may require
charging. It is recommended to charge your tool 2+ hours before use. (See page 6 for charging
instructions)
Register your tool
You can register your Bartec
Tech500 @ www.bartecusa.com.
Follow the on-screen prompts filling
in your information and tool serial
Tech 500 User Guide rev1.0 JUNE 2013
4
number. A valid serial number and supplier is required to process your registration, which can
take up to 24hrs once submitted.
Update your Tool
Once your tool is registered, verify the software level loaded to the level available online and
update your tool if necessary. Refer to section on tool updating for further instruction.
TOOL LAYOUT
TOOL CONNECTIONS
Tech 500 User Guide rev1.0 JUNE 2013
5
POWER ON/OFF SEQUENCE
The Tech500 is powered up using the ON/OFF key.
On/Off Key
To power the unit on press the On/Off Key for approx 2 seconds –the display will light showing
a logo and software version.
The unit will then display the Main Menu. All data (results and settings) from previous tests is
reloaded.
Tech 500 User Guide rev1.0 JUNE 2013
6
Power down the Tech500 by using the same ON/ OFF key.
On/Off Key
(Hold, then release when ‘Goodbye’ is displayed.) Auto power off is after 5 minutes of
inactivity.
The unit automatically powers up when the charger or USB port is in use- auto power off is not
operational.
CHARGING TOOL
NOTICE: Only use the power supply or USB cable that is included in the Tech500 tool kit to
charge this tool. The use of un-approved power supplies may damage your tool and will void
the tool warranty.
Tech 500 User Guide rev1.0 JUNE 2013
7
The Tech500 comes with the rechargeable battery already installed. Battery replacement must
be done at the factory.
For optimum performance, always keep your Tech500 sufficiently charged. It is recommended
that you charge the tool 2 + hours before first use.
The charge port is located on the right side of the tool and is the USB port opening.
TOOL DISPLAY AND ICONS
# of selections
# of selections
USB indicator
Data stored on tool
Battery indicator
Tech 500 User Guide rev1.0 JUNE 2013
8
The menu page number (e.g. x/y) on the status line indicates the menu page or item currently
displayed. The first number- x- indicates the item number selected. The second- y- indicates the
total number of items available.
USB Indicator
This status line indicator confirms the Tech500 is connected to the USB port of a computer.
Once communication has been established, results data can be viewed on the pc via the Mass
Storage Device feature. (Use the PC explorer program) “HTM File”
When the USB lead is removed the USB icon will disappear.
Battery Indicator/ Charging
This status line Indicator will illustrate the remaining charge status of the battery.
As different TPM types will ‘use up’ differing amounts of energy, the indicator can only provide
estimates of remaining life left before a recharge is required.
FULL Charge
Partial Charge - charging shortly is
suggested.
Tech 500 User Guide rev1.0 JUNE 2013
9
Little power in the battery- charging
required.
The battery is FLAT, requires
charging
When the battery is being charged the indicator segments ‘walk;’ from left to right.
When there is an insufficient amount of power remaining in the battery, the Tech500 will flash
its battery icon for two seconds, save all of the TPM Data and then power itself off.
Results Data Available Indicator
Indicates TPM data is available for viewing on the screen (using the View TPM Data command
from the main menu) or via a PC when the Tech500 is in its Mass Storage Device mode. (See
Section on Audit Mode)
Tech 500 User Guide rev1.0 JUNE 2013
10
When there is no data present, the TPM Data Indicator will not be visible.
To Access the Audit Data, connect your tool to the PC using the supplied USB Cable.
MENU SYSTEM
The Tech500’s menu system provides a hierarchy of instructions and commands. The top line of
the display will always indicate the current menu selected. The home key will always return to
the Main Menu screen- with ‘Select by Vehicle’ highlighted.
Current report
Archived reports
Andere Handbücher für Tech500
1
Inhaltsverzeichnis
Andere Bartec Messgerät Handbücher
Bartec
Bartec TECH 1000 Bedienungsanleitung
Bartec
Bartec TECH550PRO Bedienungsanleitung
Bartec
Bartec Tech200BT Bedienungsanleitung
Bartec
Bartec MAK 3003 Bedienungsanleitung
Bartec
Bartec HYGROPHIL H 4230-10 A Series Bedienungsanleitung
Bartec
Bartec ORB P-800LT Bedienungsanleitung
Bartec
Bartec RDW 03 Bedienungsanleitung
Bartec
Bartec RLAnet 17-85G5-2123 Series Technisches Datenblatt
Bartec
Bartec SYSCOM ROCK Bedienungsanleitung
Bartec
Bartec MR3000DMS Bedienungsanleitung
Bartec
Bartec Tech200 Bedienungsanleitung
Bartec
Bartec P-600 Bedienungsanleitung
Bartec
Bartec Syscom MR3000 Series Bedienungsanleitung
Bartec
Bartec VOLUTANK Petro 3003 Bedienungsanleitung
Bartec
Bartec 07-662 Series Kurzanleitung
Bartec
Bartec Tech1000 Bedienungsanleitung
Bartec
Bartec RDA01 Bedienungsanleitung
Bartec
Bartec ComEx Flex Kurzanleitung
Bartec
Bartec ALCAR TECH600 Bedienungsanleitung
Bartec
Bartec QST 250 Bedienungsanleitung
