Baxi 754 Bedienungsanleitung

5113132/02

OWNER GUIDE

This guide is intended to help you care for your Baxi Fires Division gas fire. Please read

thoroughly before using and keep for future reference.

This guide to be left with the owner

We trust that this guide gives sufficient details to enable this appliance to be operated

and maintained satisfactorily. However, if further information is required, our

Baxi Fires Division Technical Helpline will be pleased to help.

Telephone 08706 061 065 (National call rates apply in the United Kingdom).

In the Republic of Ireland telephone 0044 8706 061 065.

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Model 754

INSET LIVE FUEL EFFECT GAS FIRE

Fitted with

Amour,

Aspect,

Eclipse,

Fascination,

Landscape or

Serenity fascia

(GC No. 32-032-59)

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

At the heart of every Baxi Fires Division fire.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

OWNER GUIDE

LIST OF CONTENTS

Section

Page

SAFETY 4

GAS CONSUMPTION 5

APPLIANCE DIMENSIONS 6

OPERATING YOUR FIRE 7

The Oxysafe flame sensing and flue blockage safety system. 7

To light the fire. 7

To turn off. 9

Glass bowing. 9

Lighting with a taper. 9

CLEANING YOUR FIRE 10

Metal Parts. 10

Glass parts. 10

Ceramic fuel effect. 10

Burner. 11

FUEL BED REFITTING 11

MAINTENANCE 11

Regular maintenance. 11

Servicing. 12

USEFUL TELEPHONE NUMBERS 12

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

Page 3

OWNER GUIDE

SAFETY

have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installation instructions.

provide a minimum clearance of 700mm from the top surface of the hearth to any

shelf made of wood or other combustible material where the shelf is not more than

150mm deep. For a shelf deeper than 150mm, add 12.5mm to the clearance for every

25mm of additional shelf depth (See graph1).

Do wait three minutes before attempting to relight if the fire is switched off or the

flames are extinguished for any reason. (Your fire is fitted with a safety device that will

Page 4

OWNER GUIDE

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE - SEE YOUR LOCAL

TELEPHONE DIRECTORY

Graph 1. Combustible shelf clearances

automatically shut off the gas supply to the fire if, for any reason, the flames go out).

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are considering altering the room.

Do provide a suitable guard that complies with BS 8423 for the protection of

young children, the elderly and the infirm. Such a guard is also recommended

for the protection of pet animals. (The glass panel on the ‘Fascination’ model

conforms to the requirements of B.S. 1945:1971 and satisfies the Heating

Appliances (Fireguard) (Safety) Regulations 1991. The glass panel is very hot

when the appliance is in use and should not be touched. It does not give full

protection for young children, the elderly or infirm. The appliance should not

be used if the glass is broken).

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t

add any extra ceramic fuel effect pieces above the number stated in the fuel effect

installer and owner guide supplied with the ceramic fuel effect. This could cause

incomplete combustion and safety hazard.

Don’t put paper or any other material on the fire.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth.

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

GAS CONSUMPTION

Model 754 when fitted with Amour, Aspect, Eclipse, Landscape and Serenity fascia.

Has a maximum natural gas input of 5.1kW (Gross)

Has a maximum natural gas output of 2.6kW

Has a minimum natural gas input of 3.0kW (Gross)

Has a minimum natural gas output of 1.5kW

Model 754 when fitted with Fascination fascia.

Has a maximum natural gas input of 5.5kW (Gross)

Has a maximum natural gas output of 2.2kW

Has a minimum natural gas input of 3.1kW (Gross)

Has a minimum natural gas output of 1.1kW

Page 5

OWNER GUIDE

Page 6

OWNER GUIDE

APPLIANCE DIMENSIONS

Figure 5. Appliance dimensions and clearances (Fascia may differ from that shown)

Key Description

Model

Amour Aspect Eclipse Fascination Landscape

& Serenity

AAppliance height (mm) 610 612 599 599 607

BAppliance width (mm) 560 505 520 520 976

CAppliance depth into room

(mm) 30 13 25 61 72

Minimum mandatory

clearance to combustible

surfaces projecting beyond

the front of appliance (mm).

10 10 10 10 10

ERecommended clearance to

non-combustible surfaces

for access purposes (mm). 10 10 10 10 10

OPERATING YOUR FIRE

The Oxysafe flame sensing and flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will

shut down the appliance in the event of abnormal flue conditions.

This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe which senses that the heat from the pilot flame is

correct. If this probe is cool, the device will prevent any gas flow unless the control

knob is held in at the ignition position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

To light the fire.

Aspect model.

To gain access to the control knob lower the bottom front cover. To do this, support the

top and bottom of the lower front cover (See figure 2).

Amour model.

To gain access to the control knob lower the bottom front cover. To do this, hold the

knob on the bottom front cover and pull gently.

Eclipse and Fascination models.

To gain access to the control knob lower the bottom front cover. To do this, support the

top edges of the lower front cover and pull gently (See figure 3).

Landscape and Serenity models.

To gain access to the control knob lower the bottom front cover. To do this, gently push

the top of the front cover with the fingertips. The magnetic catch will release the front

cover (See figure4).

Depress the control knob and turn anticlockwise towards the PILOT/IGN position

(See figure 5). A spark should be generated at the pilot while turning. The spark should

ignite the pilot. The pilot flame can be seen at the left side of the fuel effect.

Page 7

OWNER GUIDE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

Keep the button at the PILOT/IGN position for a

further ten seconds. This will prevent the flame

sensing device from shutting off the gas while its

probe warms up as explained previously.

! If the pilot does not ignite quickly repeat the

procedure.

If after 10 seconds pilot ignition has not

occurred, turn the control knob back to the

“Off” position, wait for 3 minutes and then

repeat the ignition procedure.

! When the pilot is alight and stable, partially

depress the knob and turn to “LOW”. The pilot

should then light the main burner at its low setting.

There may be a delay of up to four seconds between

the pilot lighting and ignition of the gas at the main burner. This is normal and is due to

the time required to fill the main burner

compartment with sufficient gas for ignition.

! When the main burner is alight at its low

setting, partially depress the knob and gradually

turn it anti-clockwise until the burner is at your

desired level. The burner flames will gradually

increase until the knob reaches the “HIGH”

position.

Note: i) If the flames go out while setting

the control, repeat the full lighting

procedure. If the flames repeatedly go

out have the fire serviced.

ii) Please note. When first turned on the

flames will appear predominantly blue. The

fuel effect will take time to warm up.

Although some glow will be seen after

approximately ten minutes, the full visual

effect will only be apparent after a

somewhat longer time.

iii) The appliance will operate to its

maximum potential if the flue is primed

during the first 20 – 30 minutes of

operation. To do this, simply set the control

knob to its ‘HIGH’ setting. This will also

burn off any carbon deposits that may have

Page 8

OWNER GUIDE

Figure 4. Eclipse and

Fascination lower front cover

Figure 3. Eclipse and

Fascination lower front cover

Figure 2. Aspect lower front

cover

formed during previous operations.

iv) If operating the appliance for

long periods it is beneficial

occasionally to

change the settings. This will also

help to remove any carbon deposits

that may form during operation.

Glass bowing.

It is normal for the glass panel on the

fascia to bow slightly when hot.

Lighting with a taper.

(See figure 6).

In the unlikely event of failure of the

ignition spark, the pilot can be lit by a

taper or long spill. Insert the taper or spill

into the gap in the fuel effect at the left hand

side. Depress the control knob, turn it to

PILOT/IGN

To turn off.

! To turn the main burner off but leave the

pilot alight, partially depress the knob and

turn to PILOT/IGN.

! To turn the fire fully off, partially depress

the knob and turn to OFF.

! Wait at least three minutes before

relighting.

! While cooling, the fuel effect may make

some crackling noises. This is quite normal.

Page 9

OWNER GUIDE

Figure 6. Lighting with a taper (Fuel

effect may differ from that shown)

Figure 5. Control knob (On ‘Landscape’

and ‘Serenity’ models the control knob

and indicator button will be spaced away

from the support leg).

CLEANING YOUR FIRE

To maintain the high performance and quality finish of your fire please follow these

guidelines:

Before attempting to clean the fire, please remember to turn off the fire and wait for

the appliance to cool completely. The fire will retain heat for some time before cleaning

can begin.

If any pieces of debris are found in the hotbox, have the chimney inspected before

further use.

Metal Parts.

Clean the metal parts with a slightly damp, lint free non-abrasive cloth and then dry.

! Do not use abrasive cleaners, as these will scratch the fire surface.

! Fascia -

Clean the metal parts with a slightly damp cloth and then dry. If this does

not work apply a very small amount of ‘baby oil’ to a lint free, non-abrasive cloth and

wipe over the surface. Use a clean non-abrasive cloth to wipe off the oil.

Glass parts.

! Marks and stains on the glass can be removed using non-abrasive glass cleaner.

Non-abrasive ceramic hob cleaner can be used to remove stains.

! Note: The decorative metal surfaces within the firebox are exposed to high

temperatures. Great care has been taken to ensure that discolouration is kept to a

minimum. However, the combination of heat and variable flue conditions may result in

small amounts of discolouration or staining.

Ceramic fuel effect.

! This product uses fuel effect pieces containing Refractory Ceramic Fibres

(RCF), which are man-made vitreous silicate fibres. Excessive exposure to this

material may cause irritation to eyes, skin and respiratory tract. Consequently, it is

important to take care when handling these articles to ensure that the release of

dust is kept to a minimum.

In the unlikely event of soot forming, light coatings will usually be burnt off during

the normal operation of the fire.

! Should any soot accumulation become excessive, the fuel effect pieces should be

removed from the fire for cleaning.

Cleaning should be carried out in a well ventilated area or in the open air by gently

brushing with the pieces held away from your face so that you avoid inhaling the dust.

! We do not recommend the use of a normal domestic vacuum cleaner which may

blow dust back into the air.

! We suggest that you remove the ceramic fuel effect in the reverse order to that

shown in the ceramic fuel effect installer and owner guide. This should have been left

Page 10

OWNER GUIDE

Andere Handbücher für 754

Inhaltsverzeichnis

Andere Baxi Kamin im Innenbereich Handbücher

Baxi

Baxi Bermuda Inset 3 Super Bedienungsanleitung

Baxi

Baxi Cavendish Deluxe PCF Betriebsanleitung

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi 741FS Bedienungsanleitung

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi 941 Bedienungsanleitung

Baxi

Baxi 751 Montageanleitung

Baxi

Baxi EBONY SUPER Benutzerhandbuch

Baxi

Baxi Bermuda GF3 Betriebsanleitung

Baxi

Baxi Wonderfire AF16NV Bedienungsanleitung

Baxi

Baxi Classic 2 719 Bedienungsanleitung

Baxi

Baxi Steel & Monaco 747 Montageanleitung

Baxi

Baxi 661 Bedienungsanleitung

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi 741 Bedienungsanleitung

Baxi

Baxi 946 Bedienungsanleitung

Baxi

Baxi Wentworth Deluxe Benutzerhandbuch

Baxi

Baxi 751 Bedienungsanleitung

Baxi

Baxi churchill II 347 Bedienungsanleitung

Baxi

Baxi 759 Bedienungsanleitung

Baxi

Baxi Bermuda SL3 Betriebsanleitung

Baxi

Baxi 750M Bedienungsanleitung

Baxi

Baxi 741 Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch