Baxi Brava 4 Oxysafe Bedienungsanleitung

5112107/03

OWNER GUIDE

INSTALLER: Please leave this guide with the

owner

Model 347

RADIANT / CONVECTOR GAS FIRE

Fitted with one of the following fascia.

Brava 4 Oxysafe

Charm 4 Oxysafe or

Esquire 4 Oxysafe

(GC No. 32-032-62)

We trust that this guide gives

sufficient details to enable this

appliance to be operated and

maintained satisfactorily. However, if

further information is required, our

Baxi Fires Division Technical

Helpline will be pleased to help.

Telephone 08706 061 065 (National

call rates apply in the United

Kingdom)

In the Republic of Ireland

Telephone 0044 8706 061 065.

This guide is intended to help you care

for your Baxi Fires Division gas fire.

Please read thoroughly before using

and keep for future reference.

(including photocopying), stored in any medium by electronic means (including in any

retrieval system or database) or transmitted, in any form or by any means, whether

electronic, mechanical, recording or otherwise, without the prior written permission of

the copyright owner.

Applications for the copyright owner's permission to reproduce any part of this

publication should be made, giving details of the proposed use, to the following address:

The Company Secretary, Baxi Heating UK Limited, Pentagon House, Sir Frank Whittle

Road, Derby, DE21 4XA.

Warning: Any person who does any unauthorised act in relation to a copyright work may

be liable to criminal prosecution and civil claims for damages.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary

slightly from those given in this publication

Page 2

OWNER GUIDE

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE) ONLY.

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Page 3

OWNER GUIDE

LIST OF CONTENTS

Section

Page

SAFETY 4

APPLIANCE DIMENSIONS 6

OPERATING YOUR FIRE 7

GAS CONSUMPTION 7

The Oxysafe flame sensing and flue blockage safety system. 7

To light the fire (Manual ignition). 7

To light the fire (Electronic ignition). 8

CLEANING YOUR FIRE 9

REPLACING THE RADIANTS 10

MAINTENANCE 10

Battery replacement (Electronic ignition). 10

Regular maintenance. 11

Servicing. 11

USEFUL TELEPHONE NUMBERS 12

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

SAFETY

Page 4

OWNER GUIDE

IF YOU SMELL GAS

! DON’T SMOKE.

! EXTINGUISH ALL NAKED FLAMES.

! DON’T TURN ELECTRICAL SWITCHES ON OR OFF.

! TURN OFF THE GAS SUPPLY AT THE METER.

! OPEN DOORS AND WINDOWS TO GET RID OF THE GAS.

! IMMEDIATELY CALL THE GAS EMERGENCY SERVICE FROM A

NEIGHBOURS PHONE - SEE YOUR LOCAL TELEPHONE DIRECTORY.

Do have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installation guide.

Do allow a minimum clearance of 90mm from the top of the appliance fascia to the

underside of any shelf whether it is made from combustible or non-combustible

materials. This clearance is necessary to allow the fascia to be lifted off for servicing

and also allows sufficient access to operate the control knob. For a shelf made from

wood or other combustible materials deeper than 150mm add 12.5mm to the clearance

for every 25mm of additional shelf depth (See graph 1). Please bear this in mind if ever

you add a shelf.

Do provide a suitable guard that complies with BS 8423 for the protection of young

children, the elderly and the infirm. Such a guard is also recommended for the protectio

of pet animals. (

Although this fire conforms to all the applicable standards, it is a heating

appliance and certain parts of its surface will become hot).

Note: The guard supplied with the fire acts as a fireguard conforming to BS1945:1971

and satisfies the Heating Appliance (Fireguard) (Safety) Regulations 1991.

Do wait three minutes before attempting to relight if the fire is switched off or the

flames are extinguished for any reason. (Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire if, for any reason, the flames go out.)

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

Page 5

OWNER GUIDE

Graph 1 Shelf clearances

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum clearance of 50mm between the fascia sides and any corner wall

having combustible material or other combustible surface which projects beyond the

front of the fire (See figure 1). Please bear this in mind if ever you are considering

altering the room.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t fill in the space behind the fascia.

Don’t use the fire without the dress guard being in position.

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

completely.

Don’t use the fire with damaged radiants.

APPLIANCE DIMENSIONS

Page 6

OWNER GUIDE

Figure 1. Dimensions and clearances

Model Dimension ‘A’ (mm) Dimension ‘B’ (mm) Dimension ‘C’ (mm)

Brava 609 713 177

Charm 609 713 177

Esquire 609 708 177

GAS CONSUMPTION

Has a maximum natural gas input of 5.6kW (Gross)

Has a maximum natural gas output of 4.0kW

Has a minimum natural gas input of 1.57kW (Gross)

Has a minimum natural gas output of 1.0kW

OPERATING YOUR FIRE

The Oxysafe flame sensing and flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device that will shut

down the appliance in the event of abnormal flue conditions. This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe that senses that the heat from the pilot flame is correct.

If this probe is cool, the device will prevent any gas flow unless the control knob is held

down at the ignition position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

To light the fire (Manual ignition).

The control is shown in Figure 2.

!Depress the control knob and turn anticlockwise

towards the 1/IGN position. A spark should be

generated at the pilot while turning. The spark should

ignite the pilot. If it does not, keeping the knob

depressed, continue to turn the knob anticlockwise. A

second spark should ignite the pilot. The pilot flame

can be seen through the opening immediately below

the right hand centre radiant (See figure 3).

Page 7

OWNER GUIDE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

Figure 2.

If the pilot does not light, turn the knob back

to OFF and try again.

In the unlikely event of failure of the ignition

mechanism the pilot can be lit with a long

match or taper – See the next page.

!When the pilot has lit keep the knob

depressed for about ten seconds to allow the

flame sensing probe to warm up.

The control knob can then be set to your

preferred heat level. The settings are shown on

the table opposite.

To light the fire (Electronic ignition).

The control is shown in figure 2.

!Depress the control knob slightly and turn

anticlockwise towards the 1/IGN position. Do not

apply too much pressure as this will cause

resistance to be felt. Depress the control knob.

Sparks should be generated at the pilot. The

sparks should ignite the pilot. If the pilot does

not light, turn the control knob back to the‘OFF’

position and try again. The pilot flame can be

seen through the opening immediately below the right hand centre radiant (See figure 3).

If no sparks are generated at the pilot the battery may have no power. The battery can

be replaced as shown later in this guide.

In the unlikely event of failure of the ignition mechanism or where a replacement

battery is not available the pilot can be lit with a long match or taper – See next page.

When the pilot has lit keep the control knob depressed for about ten seconds to

allow the flame sensing probe to warm up.

Page 8

OWNER GUIDE

Figure 3.

The control control knob can then be set to your preferred heat level. The settings

are: -

To turn off partially depress the knob and turn clockwise to off. Wait at least three

minutes before attempting to relight.

Lighting with a match or taper.

Manual ignition: Depress the control knob and turn anticlockwise towards the 1/IGN

position.

Electronic ignition: Depress the control knob slightly and turn anticlockwise towards

the 1/IGN position.

While keeping the knob depressed, light the pilot by inserting a long match or taper into

the opening shown in figure 3 (Second opening from the right).

When the pilot is alight, keep the knob depressed for about ten seconds to allow the

flame sensing probe to warm up before setting to your preferred heat level.

For your own convenience, have the heater serviced as soon as possible.

CLEANING YOUR FIRE

Turn the fire off and allow it to cool before attempting any cleaning.

Normally the fire will only need dusting. The bright metal trims may be cleaned with a

damp cloth and dried with a soft duster. Obstinate marks can be removed from the guard

and trims using soapy water. Never use abrasive cleaners.

The radiants can be cleaned with a soft brush - see below for how to remove the

radiants.

Page 9

OWNER GUIDE

Control Knob

Position Radiants Condition

Centre radiants on low. Outer radiants off.

(The right hand centre radiant will glow slightly

more than than the left hand centre radiant due

to the pilot flame)

3Centre radiants fully on. Outer radiants off.

4Centre radiants fully on. Outer radiants on low.

5 All radiants fully on.

REPLACING THE RADIANTS

(See figure 4).

Always use the correct type of replacement radiant. Ask for Baxi Fires Division

part number 5110472. Turn the fire off and allow it to cool before attempting to

remove the radiants.

To remove the dress guard, gently pull the centre of the dress guard with one hand and

carefully spring out one end of the dress guard with the other. Slide the other side of the

dress guard clear of the fixing holes. Take care not to scratch the trim.

Lift the radiant upward to clear the

metal retaining bar then pull out

bottom first.

Fit the new radiant by inserting its top

under the top lip of the radiant box

then swing the bottom of the radiant

over and behind the retaining bar. It is

important that the front face of the

radiant should rest against the front

of the retaining channel. Replace the

dress guard. To do this locate one side

of the dress guard into the two side

fixing holes. Spring the dress guard

slightly and locate into the opposite

fixing holes. Take care not to scratch

the trim.

MAINTENANCE

Battery replacement (Electronic ignition).

1. The battery cover is located at the base of the fire on the right hand side.

2. To access the battery cover the fascia will have to be removed. The fascia securing

screws are located at the bottom rear of the fascia. Remove the securing screws from

both sides of the fascia.

Remove the control knob. To do this firmly hold the control knob and lift clear of the

fascia.

The fascia can now be removed. To do this firmly hold the fascia sides, gently pull

the bottom of the fascia forward whilst lifting the fascia upward and forward. Place the

fascia in a safe place.

5. Unscrew the battery cover in an anticlockwise direction.

6. Remove the battery and discard.

Page 10

OWNER GUIDE

Figure 4.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Baxi Kamin im Innenbereich Handbücher

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi Classic 2 719 Bedienungsanleitung

Baxi

Baxi EBONY SUPER Benutzerhandbuch

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi 946 Bedienungsanleitung

Baxi

Baxi 946 Montageanleitung

Baxi

Baxi BR660VA Bedienungsanleitung

Baxi

Baxi 751 Bedienungsanleitung

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi Harmony Montageanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi 748 Montageanleitung

Baxi

Baxi 739 Bedienungsanleitung

Baxi

Baxi 941 Bedienungsanleitung

Baxi

Baxi 750FS Bedienungsanleitung

Baxi

Baxi Bermuda GF3 Betriebsanleitung

Baxi

Baxi 746 Montageanleitung

Baxi

Baxi 946 Bedienungsanleitung

Baxi

Baxi 739 Gebrauchsanweisung

Baxi

Baxi 946 Montageanleitung

Baxi

Baxi 741FS Bedienungsanleitung

Baxi

Baxi Wonderfire AF16NV Bedienungsanleitung

Baxi

Baxi churchill II 347 Bedienungsanleitung

Baxi

Baxi Gallery Series Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung