Baxi 748 Bedienungsanleitung

5118938/02

OWNER GUIDE

We trust that this guide gives

sufficient details to enable this

appliance to be operated and

maintained satisfactorily. However, if

further information is required, our

Baxi Fires Division Technical

Helpline will be pleased to help.

Telephone 08706 061 065 (National

call rates apply in the United

Kingdom).

In the Republic of Ireland

Telephone 0044 8706 061 065.

This guide is intended to help you care

for your Baxi Fires Division gas fire.

Please read thoroughly before using

and keep for future reference.

This guide to be left with the owner

Model 748

Inset live fuel effect gas fire

Incorporating the BAXI FIRES DIVISION

CONTROL

Fitted with one of the following fascia.

CHIC, ENVY,

HERITAGE, LUXOR, OPULENT or

WESTMINSTER SLIMLINE.

(G.C. Number 32-032-61)

(including photocopying), stored in any medium by electronic means (including in any

retrieval system or database) or transmitted, in any form or by any means, whether

electronic, mechanical, recording or otherwise, without the prior written permission of

the copyright owner.

Applications for the copyright owner's permission to reproduce any part of this

publication should be made giving details of the proposed use, to the following address:

The Company Secretary, Baxi Heating UK Limited, Pentagon House, Sir Frank Whittle

Road, Derby, DE21 4XA.

Warning: Any person who does any unauthorised act in relation to a copyright work

may be liable to criminal prosecution and civil claims for damages.

Baxi Fires Division, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

Page 2

OWNER GUIDE

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).

WHEN CONVERTED USING CONVERSION KIT NO. 0595221 THIS

APPLIANCE IS FOR USE WITH PROPANE GAS (G31).

THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED

KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Safety First.

Baxi Fires Division fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

All Baxi Fires Division fires are manufactured to the highest standards of quality and

excellence and are manufactured under a BS EN ISO 9001 quality system accepted by

the British Standards Institute.

The Highest Standards

Baxi Fires Division is a member of the Society of British Gas Industries which works to

ensure high standards of safety, quality and performance.

Careful Installation

Baxi Fires Division is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Page 3

OWNER GUIDE

LIST OF CONTENTS

Section Page

SAFETY 5

GAS CONSUMPTION 6

APPLIANCE DIMENSIONS 7

OPERATING YOUR FIRE 8

The Oxysafe flame sensing & flue blockage safety system. 8

Lighting the pilot. 8

Lighting with a taper. 9

CLEANING YOUR FIRE 10

Metal parts. 10

Ceramic fuel effect and rear wall. 10

Burner. 10

CERAMIC FUEL EFFECT FITTING 11

MAINTENANCE 11

Battery replacement. 11

Regular maintenance. 12

Servicing. 12

USEFUL TELEPHONE NUMBERS 13

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

Page 4

OWNER GUIDE

SAFETY

Do have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installer guide

provide a minimum clearance of 750mm from the base of the fireplace opening to

any shelf made of wood or other combustible material where the shelf is not more than

150mm deep. For a shelf deeper than 150mm, add 12.5mm to the clearance for every

25mm of additional shelf depth (See graph1).

Do always use a fireguard complying with BS 8423 for the protection of young

children, the elderly or infirm.

Do wait three minutes before attempting to relight if the fire is switched off or the

Page 5

OWNER GUIDE

Graph 1. Combustible shelf clearances

IF YOU SMELL GAS

! DON’T SMOKE.

! EXTINGUISH ALL NAKED FLAMES.

! DON’T TURN ELECTRICAL SWITCHES ON OR OFF.

! TURN OFF THE GAS SUPPLY AT THE METER.

! OPEN DOORS AND WINDOWS TO GET RID OF THE GAS.

! IMMEDIATELY CALL THE GAS EMERGENCY SERVICE FROM A

NEIGHBOURS PHONE - SEE YOUR LOCAL TELEPHONE DIRECTORY.

flames are extinguished for any reason.(Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire, if for any reason , the flame goes out)

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are altering the room.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t add any extra fuel effect pieces above the number stated in the installer and

owner guide supplied with the ceramic fuel effect.

The installer may have attached it to

this guide or placed it inside

. Adding extra fuel effect pieces could cause a safety hazard

and consequent health hazards.

Don’t put paper or other materials onto your fire.

Don’t use the fire with damaged base ceramics.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth

Don’t

attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

GAS CONSUMPTION

Model 748

Has a maximum natural gas input of 6.0kW (Gross)

Has a maximum natural gas output of 3.1kW

Has a minimum natural gas input of 2.7kW (Gross)

Has a minimum natural gas output of 1.4kW

Model 748 when converted using kit number 0595221

Has a maximum propane gas input of 6.1kW (Gross)

Has a maximum propane gas output of 3.3kW

Has a minimum propane gas input of 4.3kW (Gross)

Has a minimum propane gas output of 2.3kW

Page 6

OWNER GUIDE

APPLIANCE DIMENSIONS

Page 7

OWNER GUIDE

See graph 1

Key Description

Model

Opulent &

Luxor Chic &

Envy Heritage

Westminster

AAppliance height (mm) 606 600 638 610

BAppliance width (mm) 518 467 515 510

CAppliance depth into

room (mm) 85 57 51 56

Minimum mandatory

clearance to combustible

surfaces projecting

beyond the front of

appliance (mm).

100 100 100 100

Recommended clearance

to non-combustible

surfaces for access

purposes (mm).

100 100 100 100

Figure 5. Appliance dimensions and clearances (Fascia may differ from that

shown). Dimensions are subject to manufacturing tolerance.

OPERATING YOUR FIRE

The Oxysafe flame sensing & flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will

shut down the appliance in the event of abnormal flue conditions.

This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert

advice.

This device incorporates a probe which senses that the heat from

the pilot flame is correct. If this probe is cool, the device will

prevent any gas flow unless the control knob is kept depressed at

the "Pilot/Ign" position.

If, for any reason, the flames go out when the fire is hot or if the

fire is turned off when hot, always wait at least three minutes

before attempting to relight.

Lighting the pilot.

The control is shown in figure 2.

u Slide the control button to the bottom (ignition) position marked .

In this position, the electronic ignition system should cause a series of sparks that

should light the pilot. Within four seconds of the pilot igniting, the main burner should

light at its minimum setting.

If no sparks are produced to light the pilot, the battery may need replacing. Details of

battery replacement are given further on in this guide. Until you can obtain a

replacement battery the fire can be lit with a taper as described later in this section of

the guide.

Keep the button at the ignition position for a further ten seconds. This will prevent

the flame sensing device from shutting off the gas while its probe warms up as

Page 8

OWNER GUIDE

Figure 2. Control

settings.

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

explained previously.

If low heat is required, release the button. The button will automatically spring up

to the low heat position shown in figure 2 (See note i).

For a higher heat level slide the button upwards. The burner flames and heat output

will gradually increase until the button reaches the high heat position shown in figure 2.

When the button reaches the high heat position you will feel a check to its movement.

Do not slide the button above the high heat position unless you want to turn the fire off

(See note i).

Note

If the flames go out while setting the control, repeat the full lighting procedure. If the

flames repeatedly go out have the fire serviced.

ii. When first turned on the flames will appear predominantly blue. The ceramic fuel

effect will take time to warm up. Although some glow will be seen after approximately

ten minutes, the full visual effect will only be apparent after a somewhat longer time.

iii.

The appliance will operate to its maximum potential if the flue is primed during the

first 20 - 30 minutes of operation. To do this, simply slide the control to its highest

setting. This will also burn off any carbon deposits that may have formed during

previous operations.

iv.

If operating the appliance for long periods it is beneficial to change between settings.

This will also help to remove any carbon deposits that may form during operation.

Lighting with a taper.

(See figure 3).

In the unlikely event of failure of the ignition spark,

the pilot can be lit by a taper or long spill. Insert the

taper or spill through the lower left hand opening in

the front of the fuel effect bed.

! Follow the section ‘ Lighting the pilot’ as

described previously.

Page 9

OWNER GUIDE

Figure 3. Lighting with a taper

(Fuel effect may differ from

that shown)

CLEANING YOUR FIRE

To maintain the high performance and quality finish of your gas fire, please follow these

guidelines:

Before attempting to clean the fire, please remember to turn off the fire and wait for

the appliance to cool. The fire will retain heat for some time before cleaning can begin.

If any pieces of debris are found in the hotbox, have the chimney inspected before

further use.

Metal parts.

! Clean the metal parts with a slightly damp cloth and then dry.

! Do not use abrasive cleaners as these will scratch the fire surface.

! Fascia -

Clean the metal parts with a slightly damp cloth and then dry. Do not use

polish or abrasive materials.

‘Chic’, ‘Envy’and ‘Westminster’ fascia -

To remove fingerprints from the fascia apply

a very small amount of ‘baby oil’ to a lint free, non-abrasive cloth and wipe over the

surface. Use a clean cloth to wipe off the oil.

Ceramic fuel effect and rear wall.

! This product uses fuel effect pieces and a burner compartment rear wall

containing Refractory Ceramic Fibres (RCF), which are man-made vitreous

silicate fibres. Excessive exposure to this material may cause irritation to eyes, skin

and respiratory tract. Consequently, it is important to take care when handling

these articles to ensure that the release of dust is kept to a minimum.

Light coatings of soot will usually be burnt off during the normal operation of the

fire.

Should any soot accumulation become excessive, the fuel effect pieces and rear wall

should be removed from the fire for cleaning.

Cleaning should be carried out in a well ventilated area or in the open air by gently

brushing with the pieces held away from your face so that you avoid inhaling the

dust.

! We suggest that you remove the ceramic fuel effect pieces in the reverse order to

that shown in the ceramic fuel effect installer and owner guide.

Burner.

! The burner surface can be carefully cleaned to remove any loose particles after

taking off the ceramic fuel effect pieces. Make sure that no particles are pushed into the

burner holes.

Page 10

OWNER GUIDE

Andere Handbücher für 748

Inhaltsverzeichnis

Andere Baxi Kamin im Innenbereich Handbücher

Baxi

Baxi 739 Bedienungsanleitung

Baxi

Baxi 741 Montageanleitung

Baxi

Baxi 750M Bedienungsanleitung

Baxi

Baxi 748 Montageanleitung

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi Harmony Montageanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi 751 Bedienungsanleitung

Baxi

Baxi 951 Gebrauchsanweisung

Baxi

Baxi 946 Bedienungsanleitung

Baxi

Baxi Bermuda Inset 3 Series Handbuch

Baxi

Baxi 939 Bedienungsanleitung

Baxi

Baxi Classic 2 719 Bedienungsanleitung

Baxi

Baxi 949 Montageanleitung

Baxi

Baxi 741 Bedienungsanleitung

Baxi

Baxi Gallery Series Montageanleitung

Baxi

Baxi Wonderfire AF16NV Bedienungsanleitung

Baxi

Baxi 754 Bedienungsanleitung

Baxi

Baxi Wentworth Classic Benutzerhandbuch

Baxi

Baxi 750FS Bedienungsanleitung

Baxi

Baxi 941 Bedienungsanleitung

Baxi

Baxi BERMUDA BBU HE Bedienungsanleitung

Baxi

Baxi Bermuda RG3 Betriebsanleitung

Baxi

Baxi Brava 4 Oxysafe Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung