BBV Tx40X Bedienungsanleitung
Installation Guide
Tx40X
Telemetry transmitter
Building Block Video Ltd www.bbvcctv.com
17 Apex Park, Diplocks Way, Hailsham, East Sussex, BN27 3JU, UK
Tel: +44 (0) 1323 842727 Support: +44 (0) 1323 444600
Contents
Important
4
Introduction
5
Unpacking
5
A simple Tx40X up the coax system
5
Tx40X connecting a Breakout box
6
Keypad functions
7
Lens action
7
Auxiliary function switches
8
Receiver self test
8
Iris level program
8
Presets
9
Patrols
10 - 11
Spare outputs
12
Sending # Commands
12
Selecting protocols on the Tx40X
12
Tx40X camera address selection
Self Test on Keypad
13
14
TX400
Tx40X manual V1.06 July 2015 4
IMPORTANT
Please read the following points before servicing or installing.
Pre-installation checks - It is recommended that the unit be bench tested prior to installation on the site.
Safety during installation or servicing - Particular care should be taken to isolate the pan/tilt head in order to prevent
operation while engineering work is being carried out. In addition any ladder or other means of working on the receiver
MUST NOT rest on the pan/tilt head as it is possible for the head to move when not expected.
Safety check - Upon completion of any service or repairs to the unit, safety checks should be performed to ensure that the
unit is in proper operating condition.
Coax grounding - If an outside cable system is connected to the unit, be sure the cable system is grounded.
Adhere to Safety Standards - All normal safety precautions as laid down by British Standards and the Health and Safety at
Work Act should be observed.
WARNING - TO PREVENT DANGER OF FIRE OR SHOCK, DO NOT EXPOSE THE INTERNAL COMPONENTS OF THIS EQUIPMENT
TO RAIN OR MOISTURE.
Damage requiring service - Servicing by qualified personnel should be carried out under the following conditions:
(a) When the power supply cord or plug is damaged;
(b) If liquid has been spilled, or objects have fallen into the unit;
(c) If the unit does not operate normally by following the operating instructions.
(d) If the unit has been dropped or the enclosure is damaged;
Replacement parts - If replacement parts are required, ensure that only replacement parts recommended by the product
manufacturer are used.
Tx40X manual V1.06 July 2015 5
Introduction
The Tx40X is very easy to use keypad for single up the coax controlled camera or single/multiple RS485/422 controlled
camera CCTV systems. It is easily installed into either a new or an existing system simply by connecting a BNC input and
output, or the twisted pair cable and a 12Vdc supply.
The Tx40X is a powerful tool for the field engineer and can control all:
128
addresses of the BBV422
255
addresses of the Pelco D
32
addresses of the Pelco P
Unpacking
Inspect the packaging for signs of damage. If damage has occurred, advise the carriers and/or the suppliers immediately.
Unpack the transmitter carefully and check that all the items are included:
Part
number
Description
Tx40X
12V PSU
Manual
Break Out
Box
Grey Cat5
Cable
Tx40X
Telemetry transmitter P/T/Z with 9 presets, wash, wipe,
lights, Autopan
X
X
X
X
X
BBV Receiver
RG59 (250m) or
CT125 (500m)
Tx40X
12Vdc
PSU
1 2 3
0
5 64
8 97
PROGRAM
AUTOPAN
FFFN
A simple Tx40X up the coax system
Tx40X manual V1.06 July 2015 6
=5
NC=6
0VSupply=7
0VSupply=8
NC3=
+12Voptionalinput2=
+12Voptionalinput1=
4=
Breakoutbox
TxA
TxB
BBVReceiver
Tx40X
12Vdc
PSU
FFFN
1 2 3
0
5 64
8 97
PROGRAM
AUTOPAN
Upto1200moftwistedpair
1 2 3
0
5 64
8 97
PROGRAM
AUTOPAN
FFFN
Tx40X connecting to a Breakout box
Tx40X manual V1.06 July 2015 7
Keypad Functions
Joystick Actions
Pan, Tilt & Zoom
PAN LEFT PAN RIGHT
TILT DOWN
TILT UP
TWIST ANTI
CLOCKWISE
ZOOM OUT
TWIST
CLOCKWISE
ZOOM IN
Lens Actions
FFFN
There are four lens function switches on the Tx40X keypad. These
are IRIS OPEN, IRIS CLOSE, FOCUS NEAR and FOCUS FAR.
ZOOM IN & ZOOM OUT are controlled via the joystick. Clockwise
will zoom in and anti clockwise with zoom out, twist joystick until the
desired picture is obtained.
Note: If the action is activated for longer than one second, High
Speed Lens Action is activated. Inching is achieved by quick
activations of the desired Action.
Tx40X manual V1.06 July 2015 8
Auxiliary Function Switches
There are four auxiliary function switches on the Tx40X keypad:
AUTOPAN
WASH - Press and hold for washer motor to run
WIPE - Latching output, press on/press off the button goes red to signify on
AUTOPAN - Press, button turns on and the Autopan motor starts. Panning Left or Right stops Autopan
LIGHTS - Latching output, press on/press off the button goes red to signify on
Receiver Self Test (This function is only available for BBV coax)
Iris Level Program (This function is only available for BBV coax)
To preset the aperture of the iris, press IRIS OPEN or IRIS CLOSE until the desired level is reached, and then press and hold
PROGRAM whilst pressing WIPE to set.
Set the
Iris level
PROGRAM
then and
Note: After adjustment, there is a 15 second period in which to program the Iris setting. After this time, the iris reverts to
its default setting.
PROGRAM
To run a receiver self test, press and hold
PROGRAM whilst pressing WASH. This
activates the self test routine in the BBV range
of receivers. See the receiver Installation Guide
for more details.
Tx40X manual V1.06 July 2015 9
The remainder of this manual refers to features found only on the receivers supporting presets, Rx10X dome interface,
Rx400P AC preset receiver, Rx45X and Rx55X multiple protocol advanced receivers.
PRESETS
To select a programmed preset, press one of the Preset keys 1to 9.
1 2 3
564
8 97
PROGRAMMING A PRESET
Position the camera using UP/DOWN and LEFT/RIGHT arrows. Then set Zoom and Focus. When satisfied with the position
and the quality of the picture, press and hold PROGRAM then press and release one of the Preset keys 1 to 9.
PROGRAM
Then
relevant
Preset: 1to 9
TO ERASE A PRESET
Select the preset to be erased, then press and hold PROGRAM then press and release IRIS OPEN.
For example, to erase Preset 4, press and release preset key 4, press and hold PROGRAM, then press and release IRIS OPEN.
PROGRAM and
Tx40X manual V1.06 July 2015 10
PATROLS (This function is only available for BBV coax)
A Patrol automatically runs through a sequence of selected presets with a programmed delay between each preset. The
receiver continues in this mode until a pan or tilt key is pressed.
Each BBV receiver is capable of operating two patrol modes made up of the 16 presets. The Tx40X will only control the first
9 presets. When a preset is programmed it is automatically entered into both patrols. Presets can be removed from either
patrol to make up the required sequences.
If a preset is erased it is automatically removed from a patrol.
To remove a preset from Patrol 1:
Select the preset you wish to remove from the patrol by pressing the appropriate Preset key. Press and hold PROGRAM
whilst pressing FOCUS FAR.
PROGRAM and FF
To remove a preset from Patrol 2:
Select the preset you wish to remove from the patrol by pressing the appropriate Preset key. Press and hold PROGRAM
whilst pressing FOCUS NEAR.
PROGRAM and FN
Starting a Patrol:
On starting a patrol the receiver will immediately move to the first preset in the patrol.
To start patrol 1 - Press and hold PROGRAM whilst pressing AUTOPAN.
PROGRAM and AUTOPAN
To start patrol 2 - Press and hold PROGRAM whilst pressing LIGHTS.
PROGRAM and
Stopping a Patrol: Patrols can be stopped at any time by moving the joystick LEFT, RIGHT, UP or DOWN.
Inhaltsverzeichnis
Andere BBV Sender Handbücher
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
