Beaba MILKEO Bedienungsanleitung

MILKEO

www.beaba.com

a e

f g h

b d

22° C

37° C - 70 ° C 60 ml – 270 ml 6g – 65g

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE.

1. Safety instructions

CAUTION, BURNING RISK

USE

ELECTRICAL CONNECTION

VIGILANCE/CHILDREN

PRECAUTIONS

2. Legend

Product:

1Powder reservoir

2Water reservoir

3On button

5Mixing compartment

6Control panel

7Cleaning brush

Control panel:

aLock button

bHot water dispenser button

cSetting button

dBottle preparation button

eAuto-clean button

fTemperature indicator

gWater quantity indicator

hPowder quantity indicator

3. Switching on the product

- Pour the water into the water reservoir 2

- Pour the powder into the powder reservoir 1

- Plug in the product

- Press the power button. 3

pressingthe button. At the end of the cycle put on the powder reservoir.

- If you do not use the product for a period of 3 minutes, the control panel locks automatically. To unlock it, press the lock/

unlock button for 1,5 seconds

- You can lock the control panel manually by pressing the lock/unlock button for 1,5 seconds

- Press once on the settings button

Set the desired temperature with the + and – buttons

- Press again on

about the quantity of power, follow the indications in the next section.

- Press the settings button

- Place the bottle on the bottle stand 4selecting one of the two heights according to the size of the bottle

- Press the bottle preparation button to prepare a bottle.

The settings will be saved for the following bottles. Repeat the operation to change the settings. If you modify the quantity

5. Dosing the powder

To determine the quantity of powder, check whether your brand of powder indicates the weight of a measure.

• If the weight is indicated:

-Set the quantity of water at 60 ml

-Double the weight of a measure and set the quantity of powder at this value.

You can then modify the quantity of water, the powder/water ratio will be saved.

• If the weight is not indicated:

-Weigh out 3 measures to obtain a reference weight

-Set the quantity of water at 90 ml

-Set the quantity of powder at the reference weight

You can then modify the quantity of water, the powder/water ratio will be saved.

• If you cannot weigh out 3 measures, you can temporarily set 9 g of powder for 60 ml of water.

Note: The dosage of your baby bottle may vary slightly depending on the density of your milk powder.

6. Bottle preparation function

To prepare a bottle:

- Place the bottle on the bottle stand 4

- Press the preparation button to start the preparation

Press any button to stop preparation

7. Hot water function

This function is for dispensing hot water at 22 to 70°

The water is dispensed at the quantity and temperature indicated on the control panel 6. You can modify these values

in the same way as for bottle preparation

- Place a recipient on the bottle stand 4

-Press the hot water dispenser button to obtain hot water

Press any button to stop dispensing manually.

8. Auto-clean function

The auto-clean function produces hot water to clean the Mixing compartment 5

- Place a recipient able to contain at least 220 ml on the bottle stand 4

- Remove the powder reservoir

- Press the auto-clean button

- Check that there is enough water in the reservoir before starting the cleaning cycle.

- Replace powder reservoir

9. Cleaning

Cleaning :

1. If there is water on the surface of the product, wipe with a dry cloth. Be sure to lock the control panel with the lock

button 6

2. Do not place the product in a humid environment

3. When the product is not used for an extended period, we recommend that you unplug it

4. Verify and clean the mixing compartment regularly 5

5. Rinse and clean the powder 1and water 2reservoirs regularly. Usethe bottle brush to remove powder in the corners.

6. Do not use a hard brush, organic abrasive products, or organic solvents to clean the mixing compartment 5

7. Before storing the product, empty and clean the powder reservoir and the water reservoir. To empty any excess water

in the circuit, remove the water tank, press the cleaning button for 5 seconds to drain the water circuit. To restart the

product press the start button 3

10. Problem/Solution

Problem Possible causes Possible solutions

Andere Handbücher für MILKEO

Inhaltsverzeichnis

Andere Beaba Flaschenwärmer Handbücher

Beaba

Beaba Bib'bain-marie Bedienungsanleitung

Beaba

Beaba BIB EXPRESSO BEA0206 Bedienungsanleitung

Beaba

Beaba Bib'bain-marie Bedienungsanleitung

Beaba

Beaba Bib'Expresso Bedienungsanleitung

Beaba

Beaba BABYMILK SECOND Bedienungsanleitung

Beaba

Beaba BABYMILK SECOND Bedienungsanleitung

Beaba

Beaba MILKEO Bedienungsanleitung

Beaba

Beaba Bib'secondes Bedienungsanleitung

Beaba

Beaba Bib'secondes Bedienungsanleitung

Beaba

Beaba Milk Prep Bedienungsanleitung

Beliebte Flaschenwärmer Handbücher anderer Marken

Topcom

Topcom KD-4302 Bedienungsanleitung

SEVERIN

SEVERIN BK-3177 Bedienungsanleitung

SEVERIN

SEVERIN BK 3176 Bedienungsanleitung

Chicco

Chicco 06867 MU Bedienungsanleitung

Reer

Reer Multimax 2 in 1 -travel Bedienungsanleitung

Lionelo

Lionelo Thermup Go Bedienungsanleitung

TEFAL

TEFAL Disney Baby TD1100K0 Bedienungsanleitung

TrueLife

TrueLife INVIO BW Single Bedienungsanleitung

Gourmia

Gourmia JBW-250 Bedienungsanleitung

König Electronic

König Electronic HC-BW10 Bedienungsanleitung

Gourmia

Gourmia JBW-150 Bedienungsanleitung

NUK

NUK MEDICPRO 10.256.467 Bedienungsanleitung

Petra

Petra DI 6.00 Bedienungsanleitung

Philips AVENT

Philips AVENT Electric Bottle and Baby Food Warmer Bedienungsanleitung

babymoov

babymoov Auto Speed Bib Bedienungsanleitung

Alecto

Alecto BW600 Bedienungsanleitung

Lionelo

Lionelo Thermup Bedienungsanleitung

Philips

Philips SCF355 Bedienungsanleitung