BEAMEX MC5-IS Bedienungsanleitung
User Guide
Fieldbus Option for
PROFIBUS PA
3
User Guide
Fieldbus Option for
PROFIBUS PA
Dear user,
We have made every effort to ensure the accuracy of the contents of
this manual. Should any errors be detected, we would greatly appre-
ciate to receive suggestions to improve the quality of the contents of
this manual.
The above notwithstanding, we can assume no responsibility for any
errors in this manual or their eventual consequences.
We reserve rights to make modifications to this manual without any
further notice.
For more detailed technical data about MC5-IS Intrinsically Safe Cali-
brator, please refer to MC5-IS User Guide or contact the manufactur-
er.
© Copyright 2009
BEAMEX OY AB
Ristisuonraitti 10
68600 Pietarsaari
FINLAND
Tel +358 - 10 - 5505000
Fax +358 - 10 - 5505404
Internet: http://www.beamex.com
8822800 / UEMC5-IS-PA / 001139
4
Trademarks
QCAL®is a registered trademark owned by Beamex Oy Ab.
PROFIBUS®is a registered trademark of PROFIBUS International.
FOUNDATION™ Fieldbus is a registered trademark of the Fieldbus Foundation.
HART®is a registered trademark of the HART Communication Foundation.
Other trademarks are property of their respective owners.
5
Contents
General ......................................................................................................... 1
What is Fieldbus................................................................................................. 2
Unpacking and Inspection .................................................................................. 2
Batteries ............................................................................................................. 3
Charging the Batteries ................................................................................. 3
Disposal of Waste Electrical and Electronic Equipment ..................................... 4
Safety ................................................................................................................. 5
Symbols Used.............................................................................................. 5
Ex Information and Approvals ...................................................................... 5
Notes and Warnings .................................................................................... 8
Service ............................................................................................................. 10
Cleaning FI5-IS .......................................................................................... 10
The Battery Charger .................................................................................. 10
Terminology...................................................................................................... 11
MC5-IS, FI5-IS and PROFIBUS PA ................................................................. 12
Calibration Procedure of a Fieldbus Instrument, General .......................... 12
Device Descriptions.......................................................................................... 14
Viewing Device Descriptions in MC5-IS..................................................... 14
Device Description Sender......................................................................... 15
Fieldbus Instruments and Beamex's Calibration Database Software ............... 16
Connecting to a PROFIBUS PA Instrument............................................ 17
Connections ..................................................................................................... 18
Fieldbus and MC5-IS' Basic Mode ........................................................... 19
Connecting to a PROFIBUS PA Instrument ..................................................... 19
Fieldbus Window Setup Menu.......................................................................... 22
Disconnect Device ..................................................................................... 22
Device Information ..................................................................................... 22
Transducer Block Information .................................................................... 23
Target Mode............................................................................................... 24
Select Output ............................................................................................. 24
Trim Fieldbus Device ................................................................................. 24
Add a Fieldbus Device to Database........................................................... 25
Unit ............................................................................................................ 27
Performing a Verifying Calibration.......................................................... 28
Selecting the Instrument................................................................................... 28
Doing the Verifying Calibration......................................................................... 29
Calibrating (Trimming, Adjusting) a Fieldbus Instrument.................................. 30
6 General
Fieldbus Communication Settings .......................................................... 33
Appendix 1, Codes in Profibus PA Profile Version 3.0.......................... 34
Appendix 2, Codes in Profibus PA Profile Version 2.0.......................... 39
Notes........................................................................................................... 41
User Guide – MC5-IS Fieldbus Option for PROFIBUS PA
General 1
General
FI5-IS Intrinsically Safe Fieldbus Interface allows you to ca-
librate Intrinsically Safe PROFIBUS PA fieldbus instruments.
All you need is a fieldbus compatible MC5-IS and a FI5-IS
suited for your fieldbus type.
The MC5-IS/FI5-IS for PROFIBUS PA features listed below
are presented in more detail further on in this manual.
Takes the role of PROFIBUS Master when connecting to
PROFIBUS segment.
Capability to read and edit the instrument Tag.
Read and assign the instrument Node Address.
Read and edit the Transducer Block parameters.
Device Descriptions supported.
Note.
MC5-IS/FI5-IS does not support Device Description Me-
thods.
FI5-IS is Intrinsically Safe when used together with
MC5-IS only.
User Guide – MC5-IS Fieldbus Option for PROFIBUS PA
2 General
What is Fieldbus
Fieldbus is an industrial digital communications network specif-
ically designed for process automation use. It is meant to re-
place the existing standard 4 … 20 mA analog signal.
Fieldbus technology has been around since late 80's, but de-
veloping an international standard took a long time. There still
are several different types of fieldbus implementations, but
some of them have become more dominant than others. The
two most widely spread types are:
PROFIBUS (www.profibus.com/pb/profibus/process/).
FOUNDATION Fieldbus (www.fieldbus.org/) and
Both are based on IEC fieldbus standard, 61158.
Unpacking and Inspection
At the factory each new FI5-IS passes a careful inspection. It
should be free of scrapes and scratches and in proper opera-
tion order upon receipt. The receiver should, however, inspect
the unit for any damage that may have occurred during transit.
If there are signs of obvious mechanical damage, package
contents are incomplete, or the instrument does not operate
according to specifications, contact the purchasing sales office
as soon as possible. The standard accessories are as follows:
A warranty card,
a Declaration of Conformity,
this User Guide,
a separate multi-lingual booklet entitled
“FI5-IS Safety Information”,
MC5-IS - FI5-IS communication cable,
FI5-IS cable (fieldbus communication test leads),
fieldbus resistor for FI5-IS and
battery charger, type BC09-IS.
User Guide – MC5-IS Fieldbus Option for PROFIBUS PA
General 3
Batteries
The rechargeable battery inside FI5-IS provides supply power
to the communication between MC5-IS and FI5-IS.
With fresh, fully charged batteries, FI5-IS may be used for ap-
prox. 10 hours without recharging. To save batteries, discon-
nect the fieldbus cables when FI5-IS is not used. When the
front panel light is not visible, there is a minimal load on the
batteries.
Use the battery charger, BC09-IS for charging the batteries.
Using other chargers may put the safety at risk.
Charging the Batteries
The charger, BC09-IS, for rechargeable batteries operates in
the following environments:
- Voltage: 100 … 240 VAC
- Frequency: 50/60 Hz
The charging time is 16 hours. When taking FI5-IS into use for
the first time, fully charge FI5-IS batteries (16 hours).
Warnings!
USE CHARGER IN SAFE AREA ONLY. The casing of the
charger is not IS-compliant.
USE ONLY THE CHARGER PROVIDED WITH FI5-IS.
The charger should only be used indoors and when charging,
the environment temperature should be between 0 … +35 °C
(32 … 95 °F).
See also General Warnings on page 8.
Front Panel Light
The light on the front panel of FI5-IS is red while charging.
When not charging, fieldbus cables are connected and fieldbus
power for FI5-IS is available, the light is green.
If FI5-IS battery is almost empty, the green light is dimmed. If
battery is completely discharged, the green light is not visible.
Note.
Although the led is lit (green), communication is not in-
itiated until MC5-IS is connected to FI5-IS.
User Guide – MC5-IS Fieldbus Option for PROFIBUS PA
4 General
Disposal of Waste Electrical and Electronic Equipment
Beamex is an environmentally conscious company developing
products with a view to ensure that they are easy to recycle
and do not introduce hazardous materials into the environ-
ment.
In the European Union (EU) and other countries with separate
collection systems, waste from electrical and electronic equip-
ment (WEEE) is subject to regulations.
EU WEEE Directive 2002/96/EC (the WEEE Directive) re-
quires that producers of electronic equipment are responsible
for the collection, reuse, recycling and treatment of WEEE
which the Producer places on the EU market after August 13,
2005. The objective of this regulation is to preserve, protect
and improve the quality of the environment, protect human
health, and conserve natural resources.
The symbol on the left is also printed on the prod-
uct's sticker. It indicates that this product should be
handed over to applicable collection point for the re-
cycling of electrical and electronic equipment.
For more detailed information about recycling of this product,
please contact your local representative or your waste disposal
service.
User Guide – MC5-IS Fieldbus Option for PROFIBUS PA
General 5
Safety
Symbols Used
The following symbols concerning electrical safety are used in
FI5-IS.
Caution! See manual for further information
Ex Information and Approvals
Please read the separate leaflet shipped with FI5-IS entitled (in
English) Safety Information for Beamex MC5-IS Intrinsically
Safe Multifunction Calibrator. The leaflet includes the same
safety information in several languages.
Ex Approvals:
ATEX IEC
Ex ib [ia] IIC T4
(Tb = -20 … 50°C)
VTT 09 ATEX 005X
Ex ib [ia] IIC T4
(Tb = -20 … 50°C)
IECEx VTT 09.0001X
0537
Andere Handbücher für MC5-IS
1
Inhaltsverzeichnis
Andere BEAMEX Messgerät Handbücher
