BEC MX-1200 Bedienungsanleitung
BEC MX-1200
(4G/LTE) Gigabit Multi-Service
Broadband Router
Quick Start Guide
BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router
1
Package Contents
✓BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router * 1
✓This Quick Start Guide *1
✓RJ-45 Ethernet Cable * 1
✓2.4GHz Wi-Fi Antenna (Short) * 2 + 5GHz Wi-Fi Antenna (Long) * 2
✓MiniFIT to DC Power Cable *1
✓DC Power Adapter * 1
✓Mounting Bracket * 1
NOTE:ALL IMAGES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY.
PACKAGE CONTENTS MAY DIFFER FROM ACTUAL PRODUCTS.
Warning
⚫Do not use the router in high humidity or at high temperature.
⚫Do not use the same power source for the router as other equipment.
⚫Do not open or repair the case yourself. If the router is too hot, turn off
the power immediately and have it repaired at a qualified service center.
⚫Avoid using this product and all accessories outdoors.
Attention
⚫Place the router on a stable surface.
⚫Only use the power adapter that comes with the package. Using a
different voltage rating power adapter may damage the router.
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE ONLINE USER
MANUAL.
Quick Start Guide
2
Front Panel - Connectors
PORTS
MEANING
I
(Optional)
LTE 1
(Main/GPS/Aux)
Antenna
Connectors
MX-100U as Primary LTE Connectivity
SMA female connectors
Manually screw the mobile and/or GPS antennas tight to the female connectors for
mobile connection 1
II
(Optional)
LTE 2
(Main/GPS/Aux)
Antenna
Connectors
MX-1200 Embedded as Secondary LTE Connectivity
SMA female connectors
Manually screw the 3G/4G and/or GPS antennas tight to the female connectors for
mobile connection 2
III
Gigabit
LAN Ethernet
(1 - 4)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when
connecting to a PC or an office/home network of 10Mbps /100Mbps /1000Mbps
* LAN 1/EWAN 1 & LAN 2/EWAN 2
Connect to a Fiber/ Cable/ xDSL Modem with using a RJ-45 cable for broadband
connectivity
Note: LAN1 and/or LAN2 automatically becomes an EWAN port when EWAN internet
interface is configured in the management GUI
IV
USB Ports
The USB can support setup for storage/file sharing. Connect an external USB dongle /
hard drive for storage
V
Power
Connect the supplied Power cable to this jack port
BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router
3
Front Panel - LEDs
LEDS
MEANING
1
LTE 1 / LTE 2
(Received
Signal
Strength
Indicator)
Green
RSSI greater than -69 dBm. Excellent signal condition
Green Flashing
quickly
RSSI from -81 to -69 dBm. Good signal condition
Red Flashing
quickly
RSSI from -99 to -81 dBm. Fair signal condition
Red Flashing
slowly
RSSI less than -99 dBm. Poor signal condition
Red
No signal and the 4G LTE module is in service
Off
No LTE module or LTE module fails
2
GPS
Green
GPS is up and ready to use
3
USB 1 / USB 2
Green
Connecting to a USB dongle or a hard drive
4
Internet
Green
Internet is connected, and traffic is passing through the device
Red
IP request failed
Off
Either in bridged mode or WAN connection is not ready
5
Power
Green
System is up and ready
Red
Boot failure
6
Gigabit
Ethernet
(LAN 1 - 4)
Green
Transmission speed is at Gigabit speed (1000Mbps)
Orange
Transmission speed is at 10/100Mbps
Blinking
Data being transmitted/received
Quick Start Guide
4
Back Panel –Wi-Fi Connectors & LEDs
LEDS
MEANING
7
Wi-Fi 2.4G / 5G
Green
Wireless connection to 2.4G or/and 5G network is established
Blinking
Data being transmitted / received
PORTS
MEANING
VI
2.4GHz
Wi-Fi Antenna
Find two (2) short 2.4GHz Wi-Fi antennas and screw them onto the antenna
connectors
VII
5GHz
Wi-Fi Antenna
Find two (2) long 5GHz Wi-Fi antennas and screw them onto the antenna
connectors
VIII
WPS &
Wireless
On/Off
By controlling the pressing time, users can achieve two different effects:
(1) WPS*: Press &hold the button for less than 6 seconds to trigger WPS function.
(2) Wireless ON/OFF button: Press & hold the button for more than 6 seconds to
enable or disable the wireless.
* Refer to the WPS section in the User Manual for more details.
XI
Reset
After the device is powered on, press it 6 seconds or above: to restore to factory
default settings (this is used when you cannot login to the router, e.g. forgot your
password)
SIM1 / SIM2
Card Slots
Primary: SIM1. Secondary: SIM2
If only have one SIM card, insert it to SIM1.
Insert the mini SIM card (2FF) with the gold contact facing up.
Push the mini SIM card (2FF) inwards to eject it
* Power off the MX-1200 before inserting or removing the SIM card(s)
BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router
5
Hardware Connection
LTE & GPS
2.4GHz and 5GHz Wi-Fi
Quick Start Guide
6
Hardware Installation
1. Power Connection
There are two power sources to power on the MX-1200. (1) DC power adapter or (2) Vehicle
Electrical System
A. Using the Supplied DC Power Adapter
Attach the miniFIT-to-DC-Power-Cable to the 4-pin connector of the MX-1200. Then plug in
the supplied power adapter to the wall and the power plug to the DC jack of the power cable to
power ON the MX-1200.
B. Using Vehicle Electrical System
Attach the vehicle hardware power cable to the MX-1200 and connect the wire leads of the
power cable to the vehicle’s electric system
MiniFIT to DC
Power Cable
Vehicle
Power Cable
BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router
7
Power PIN Definition
BLACK Wire (PIN 1 & 2): Ground (GND). Use one of the BLACK wires for a neutral or ground
connection
WHITE Wire (PIN 3): ACC/ON for Ignition Input wire need to be connecting into vehicle
accessory wire.
RED Wire (PIN 4): VCC/OFF Voltage wire to the battery. DC power range from 0V to 56V.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to
the PC’s Ethernet interface.
3. WAN Link Interface and Connection
BEC MX-1200 supports Internet failover and failback on multiple WAN interfaces, dual EWAN,
Wi-Fi WAN and 4G/LTE (optional) <Please refer to User Manual for detailed Internet setup>
A. Ethernet WAN Connections
MX-1200 supports dual WAN Internet connections; both WANs work simultaneously. Connect
RJ-45 Ethernet cable to one or both EWAN port(s) and connect the other side to another
alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic line.
Quick Start Guide
8
B. Wi-Fi Connection (Client Mode)
MX-1200 also supports Wi-Fi as WAN known as Wi-Fi Client. The Wi-Fi client connects to a
remote Wi-Fi Access Point (AP) for remote network or Internet access.
MX-1200 supports both 2.4GHz and 5GHz. Currently, the Wi-Fi client only available in the
2.4GHz band.
C. 4G/LTE Connection (Via MX-100U 4G/LTE Modem)
Insert the MX-100U to the MX-1200
Using the MX-100U, a 4G/LTE modem, to upgrade your existing MX-1200 to support mobile
4G/LTE service.
1) Remove the metal plate.
2) Insert the SIM card(s). MX-100U supports dual-SIM and failover feature.
NOTE: Insert the SIM with gold contact facing up. Make sure that the SIM card has been slid into the
bottom of the slot with a click. When removing the SIM card, press the SIM card again it will be ejected from the
card slot.
3) Insert and firmly attach the MX-100U to the MX-1200.
4) Put and screw the metal plate back to the MX-1200.
Andere Handbücher für MX-1200
1
Inhaltsverzeichnis
Andere BEC Netzwerk-Router Handbücher
BEC
BEC RidgeWave 6900 Bedienungsanleitung
BEC
BEC MX-210NP Bedienungsanleitung
BEC
BEC 7700N Bedienungsanleitung
BEC
BEC MX-200 Bedienungsanleitung
BEC
BEC 4700A Bedienungsanleitung
BEC
BEC 5200 Series Bedienungsanleitung
BEC
BEC 7300N Bedienungsanleitung
BEC
BEC 7402GTM Bedienungsanleitung
BEC
BEC BEC 6500AEL Bedienungsanleitung
BEC
BEC 7300 Series Bedienungsanleitung
BEC
BEC M2M MX-1000e Bedienungsanleitung
BEC
BEC MX-1200 Bedienungsanleitung
BEC
BEC 5200 Series Bedienungsanleitung
BEC
BEC 6600AEL Bedienungsanleitung
BEC
BEC MX-200 Bedienungsanleitung
BEC
BEC RidgeWave 7000 R26-W Bedienungsanleitung
BEC
BEC BEC 7800(N) Bedienungsanleitung
BEC
BEC 7700N Bedienungsanleitung
BEC
BEC 7800TN Bedienungsanleitung
BEC
BEC 8800N Bedienungsanleitung
