Becker Centronic SunWindControl SWC245A-II Bedienungsanleitung

Centronic SunWindControl

SWC245A-II

en Assembly and Operating Instructions

5-channel hand-held transmitter for wind

control unit

Important information for:

• Fitters / • Electricians / • Users

Please forward accordingly!

These instructions must be kept safe for future reference.

Becker-Antriebe GmbH

Friedrich-Ebert-Straße 2-4

35764 Sinn/Germany

www.becker-antriebe.com

4033 630 279 014/07/2022

Table of contents

General ................................................................................................... 3

Warranty ................................................................................................. 3

Safety instructions ................................................................................... 4

Intended use ........................................................................................... 5

Explanation of displays and buttons........................................................... 6

Explanation of functions ........................................................................... 6

Factory default settings ............................................................................ 8

Programming the transmitter .................................................................... 9

Installing the wall bracket.........................................................................10

Changing batteries..................................................................................10

Cleaning.................................................................................................10

Technical data ........................................................................................11

What to do if...?.......................................................................................11

2-en

General

With this transmitter you are able to control up to 5 sun protection systems via

assigned channels, individually or together, and set the threshold value for

wind monitoring with the setting tool included. The set threshold applies to all

channels.

This device is exceptionally easy to use.

Please observe these Assembly and Operating Instructions when installing

and setting up the equipment.

Explanation of pictograms

CAUTION CAUTION indicates a hazardous situation

which, if not avoided, could result in in-

jury.

ATTENTION ATTENTION indicates measures that must

be taken to avoid damage to property.

Denotes user tips and other useful in-

formation.

Warranty

Structural modifications and incorrect installation which are not in accordance

with these and our other instructions can result in serious injuries, e.g., crush-

ing of limbs. Therefore, structural modifications may only be carried out with

our prior approval and strictly in accordance with our instructions, particularly

the information contained in these Assembly and Operating Instructions.

Any further processing of the products which does not comply with their inten-

ded use is not permitted.

The end product manufacturer and fitter have to ensure that all the relevant

current statutory, official and, in particular, EMC regulations are adhered to

during utilisation of our products, especially with regard to end product manu-

facture, installation and customer advice.

3-en

Safety instructions

General information

•Please keep the instruction manual safe!

•Only use in dry rooms.

•Only use unmodified original parts from the control unit manufacturer.

•Keep children away from control units.

•Observe all pertinent country-specific regulations.

•Dispose of used batteries properly. Only replace the battery with one of

the same type (see Technical Data).

Caution

•Keep people out of the system’s range of travel.

•If the system is controlled by one or more transmitters,

the system’s range of travel must always be visible during

operation.

•Device contains small parts that can be swallowed.

Caution

THIS PRODUCT CONTAINS A LITHIUM BATTERY.

If swallowed, a lithium battery can cause severe or fatal in-

juries within 2 hours.

Keep batteries away from children.

If you think batteries may have been swallowed or placed in-

side any part of body, seek immediate medical attention.

4-en

Intended use

The transmitter described in these instructions must only be used indoors for

the operation of Centronic-compatible radio drives and radio control units for

sun protection systems.

Attention

A safety-relevant function has been provided for the

threshold controller. Setting the threshold value wrongly can

cause damage to the sun protection system. For that reason,

setting the threshold value for the safety of your sun protec-

tion system should only be done by – or under the instruction

of – a specialist retailer.

•Please note that radio-controlled systems may not be used in areas with

a high risk of interference (e.g. hospitals, airports).

•The remote control is intended solely for use with equipment and sys-

tems in which malfunctions in the transmitter or receiver would not pose

any risk to persons, animals or property, or which contain safety devices

to eliminate such risks.

•The operator is not protected from interference from other telecommu-

nications systems and terminal equipment (e.g. even from radio-con-

trolled systems which are properly operated in the same frequency

range).

•Only connect radio receivers to devices and systems approved by the

manufacturer.

•Ensure that the control unit is not installed or operated

close to metal surfaces or magnetic fields.

•Radio-controlled systems transmitting on the same fre-

quency may cause reception interference.

•Note that the range of the radio signal is limited by legis-

lation as well as by design.

5-en

Explanation of displays and buttons

1. Setting tool

2. Wind threshold regulator

3. RETRACT button

4. STOP button

5. EXTEND button

6. Channel selection button

7. Channel indicator lamps

8. Programming button

9. Labelling field

10. Type plate

Explanation of functions

Channel

The channel of a transmitter can be programmed into one or more receivers.

One receiver is operated through an individual command, several receivers

through a group command.

Central command

If all the channels of the transmitter are selected, it is possible to operate all of

the assigned receivers/groups simultaneously.

6-en

Channel selection button

Up to 5channels can be selected using the channel selection button. The indi-

vidual channels are indicated by the corresponding channel indicator lamp

lighting up. If all of the channel indicator lamps light up simultaneously, the

central command can be programmed or transmitted.

You can make a note of the programmed channel in the la-

belling field underneath the transparent film.

Channel indicator lamps

A radio signal is indicated by the corresponding channel indicator lamp light-

ing up. The respective channel indicator lamp flashes while transmitting if the

battery is getting weak. The transmission strength and the radio range de-

crease as battery power declines. If the channel indicator lamp no longer

lights up when a button is pressed, the battery must be replaced.

Setting tool

When used properly, the rib on the handle of the tool serves as an orientation

aid for setting the threshold value.

Rib

1. Insert the tool in the threshold regulator.

2. Turn the threshold regulator as far as the left stop.

3. Remove the tool.

4. Now insert the tool such that the rib points in the minus direction (-).

5. Turn the tool in the plus direction (+) until the desired threshold value is

reached.

7-en

Wind threshold regulator (in connection with a suitable

sensor from the controller manufacturer)

You set the wind threshold value with this regulator (between about 2 m/s and

22 m/s).

The wind threshold value can be adjusted in 11 steps. When slowly turning the

regulator, the tubular drive clicks to indicate the setting changes.

- Left stop Stage 1, retract at low wind

+ Right stop Stage 11, retract at very high wind

Changes made to the threshold value are transferred immediately.

When setting the threshold, ensure that no button is

pressed. When the wind speed exceeds the set wind

threshold value, the sun protection system retracts and re-

mains closed. The sun protection system can only be exten-

ded again after the wind speed has remained below the

threshold value for approx. 15 minutes.

The set threshold applies to all channels.

TEST mode

The TEST mode is activated by adjusting the threshold value. It automatically

ends after about 15 minutes. In TEST mode, the time for which the wind is

monitored is shortened.

Factory default settings

Wind threshold value Left stop (about 2 m/s)

8-en

Programming the transmitter

Caution

Before programming the transmitter, check that the

threshold controller is as set at the factory. Make sure when

programming the transmitter that you are not in the travel re-

gion of the sun protection system.

1) Programming the master transmitter

a) Readying the receiver for programming

The master transmitter refers to the very first transmitter

programmed in a receiver. In contrast to subsequently pro-

grammed transmitters, the master transmitter enables,

among other things, the setting of limit positions and the

programming or deleting of further transmitters. Any trans-

mitter that has separate UP, STOP, DOWN buttons and a pro-

gramming button can be a master transmitter.

Follow the Assembly and Operating Instructions for the re-

ceiver.

Operate the programming button on the transmitter using a

suitable cylindrical tool (e.g. a ballpoint pen).

•Switch off the power supply to the receiver for 5 seconds, then switch it

back on

•Operate the programming button or the radio switch of the receiver.

The receiver is now in programming mode for 3 minutes.

b) Programming the master transmitter

Press the programming button on the master transmitter while in program-

ming mode until the receiver confirms that programming has been successful.

The programming process is now complete.

2) Programming additional transmitters

1. Press the programming button of the master transmitter until the re-

ceiver confirms.

2. Then press the programming button of the new transmitter until the re-

ceiver confirms.

3. Now press the programming button of the new transmitter again.

4. The receiver confirms successful programming.

9-en

Installing the wall bracket

Unlocking mechanism

Wall bracket

mounting

plate

Wall bracket

•Before installation in the de-

sired installation position,

check that the transmitter and

receiver are functioning prop-

erly.

•Fix the bracket to the wall with

the two screws enclosed.

Changing batteries

You will find the appropriate battery type in the "Technical

data" chapter.

Cleaning

Only clean the device with a suitable cloth. Do not use aggressive cleaning

agents that may damage the surface.

10-en

Inhaltsverzeichnis

Andere Becker Sender Handbücher

Becker

Becker CentronicPLUS EC548 PLUS Bedienungsanleitung

Becker

Becker CentronicPLUS SWC548 PLUS Bedienungsanleitung

Becker

Becker Centronic SunWindControl SWC411 Bedienungsanleitung

Becker

Becker Centronic SunWind Control SWC241A-II Bedienungsanleitung

Becker

Becker Centronic EasyControl Bedienungsanleitung

Becker

Becker Centronic SunWindControl SWC241-II Bedienungsanleitung

Becker

Becker Centronic EasyControl EC5410-II Bedienungsanleitung

Becker

Becker Centronic MemoControl MC411-III Bedienungsanleitung

Becker

Becker Centronic EasyControl EC411A-III Bedienungsanleitung

Becker

Becker Centronic EasyControl EC5410A-II Bedienungsanleitung

Becker

Becker Centronic EasyControl EC411 Bedienungsanleitung

Becker

Becker Centronic SunWindControl SWC442-II Bedienungsanleitung

Becker

Becker CentronicPLUS SWC541A PLUS Bedienungsanleitung

Becker

Becker CentronicPLUS EC541 PLUS Bedienungsanleitung

Becker

Becker Centronic MemoControl MC511 Bedienungsanleitung

Becker

Becker B-Tronic VarioControl VC5801B Bedienungsanleitung

Becker

Becker Centronic MemoControl MC415 Bedienungsanleitung

Becker

Becker Centronic EC548 Plus Bedienungsanleitung

Becker

Becker CentronicPLUS SWC541 PLUS Bedienungsanleitung

Becker

Becker Centronic / B-Tronic EasyControl MC611 Bedienungsanleitung

Becker

Becker B-Tronic VarioControl VC3201B Stücklistenhandbuch

Becker

Becker Centronic SunWindControl SWC241 Bedienungsanleitung

Becker

Becker Centronic / B-Tronic EasyControl EC715 Bedienungsanleitung

Becker

Becker CentronicPLUS EC548A PLUS Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung