Behringer MS-1-BK Handbuch

Synthesizers and Samplers

MS-1-BK /

MS-1-BU / MS-1-RD

Analog Synthesizer with 32 Full-Size Keys,

3340 VCO with 4 Simultaneous Waveforms,

VCF, NovaMod FM Sources, 32-Step Sequencer,

Arpeggiator and Live Performance Kit

985-40000-01104 Rev.A

2021-02-03 page 1 of 5

Condential, for internal use only. Not to be reproduced.

User Support Bulletin

Introduction

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

and the following recalibration procedures can be used to bring it back to its factory settings.

Equipment required

1. A multimeter (with 1 mv resolution)

2. A 3.5 mm cable (mono or stereo should be ne)

Synthesizers and Samplers

MS-1-BK /

MS-1-BU / MS-1-RD

page 2 of 5page 2 of 5

Remove all unused cables from the MS-1.

Set the controls 1 to 8 to the position shown in the right hand column of this table.

Set all the other faders, knobs and switches shown in the photo.

Preparation

Make sure your MS-1 has been powered on for at least 30 minutes, and that it is situated in a place where the

temperature will not change drastically during calibration.

Calibration Procedure

5 6 78

No. Control Set to

1 LFO RATE M

2 WAVE FORM

3GLIDE M

4RANGE 2’

5MAIN

6 SUB OSC 2 OCT DOWN

7VCA GATE

8ENVELOPE GATE

No. CV type Description

1Internal CV Calibrates the internal CV

2Output CV Tunes the CV output

3External CV Compensate oscillator oset for external CV in

Follow all steps in the order in which they are presented.

Synthesizers and Samplers

MS-1-BK /

MS-1-BU / MS-1-RD

page 3 of 5page 3 of 5

Press “Shift + STEP1” to start Internal CV calibration.

All of the sequencer LEDs will light up in sequence after this has nished.

Press “KYBD + STEP” then power on device. All the sequencer LEDs will light up.

Wait for calibration to nish.

Internal CV Calibration

Output CV Calibration

In this mode, these buttons have new functions:

There are four test modes A / B / C / D to be calibrated. Their target voltage is 0V / 1V / 3V / 5V respectively.

Button Name Function

HOLD/REST Select test mode A

RESET/ACCENT Select test mode B

ARP/SETEND Select test mode C

PATTERN/BANK Select test mode D

SHIFT —

PAGE —

PLAY/STOP —

REC Save

Button Name Function

STEP1 Select X1 (about ±1 mV)

STEP2 Select X2 (about ±4.5 mV)

STEP4 Select X3 (about ±9 mV)

STEP4 Select X4 (about ±45 mV)

STEP5 —

STEP6 —

STEP7 —

STEP8 —

KYBD Decrease

STEP Increase

Synthesizers and Samplers

MS-1-BK /

MS-1-BU / MS-1-RD

page 4 of 5page 4 of 5

Connect the Multimeter to CV Out as shown below.

Carry out the Internal CV Calibration before starting this Output CV calibration.

Press “Shift + STEP2” to enter user Output CV calibration mode.

Press “HOLD/REST” to select test mode A. You will need to watch the multimeter to adjust the output voltage.

Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “0V”.

(Press “STEP1” “STEP2” “STEP3” or “STEP4” to select the incremental adjustment size “X1” “X2” “X3” or “X4”)

Press “RESET/ACCENT” to select test mode B.

Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “1V”.

Press “ARP/SETEND” to select test mode C.

Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “3V”.

Press “PATTERN/BANK” to select test mode D.

Press “KYBD” or “STEP” to adjust the CV value until it is close to target level “5V”.

Press “REC” to save and nish Output CV calibration.

Synthesizers and Samplers

MS-1-BK /

MS-1-BU / MS-1-RD

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global

External CV Calibration

Press “Shift + STEP3” to start External CV calibration.

Complete Output CV calibration, then connect the CV out jack to the CV in jack with a 3.5mm cable.

Wait for the calibration to nish, this is indicated by all of the sequencer LEDs will light up in sequence.

Calibration is nished. Reboot the MS-1.

End of Procedure

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Behringer Synthesizer Handbücher

Behringer

Behringer 110 VCO/VCF/VCA Bedienungsanleitung

Behringer

Behringer CRAVE Bedienungsanleitung

Behringer

Behringer POLY D Bedienungsanleitung

Behringer

Behringer Victor Bedienungsanleitung

Behringer

Behringer 112 DUAL VCO Bedienungsanleitung

Behringer

Behringer 2600 Bedienungsanleitung

Behringer

Behringer MonoPoly Montageanleitung

Behringer

Behringer SYSTEM 55 Bedienungsanleitung

Behringer

Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Bedienungsanleitung

Behringer

Behringer MODEL D Bedienungsanleitung

Behringer

Behringer 962 SEQUENTIAL SWITCH Bedienungsanleitung

Behringer

Behringer PRO-800 Bedienungsanleitung

Behringer

Behringer D A-440 Montageanleitung

Behringer

Behringer NEUTRON Referenzhandbuch

Behringer

Behringer DeepMind 6 Bedienungsanleitung

Behringer

Behringer ODYSSEY Bedienungsanleitung

Behringer

Behringer DeepMind 6 Bedienungsanleitung

Behringer

Behringer MonoPoly Bedienungsanleitung

Behringer

Behringer NEUTRON Bedienungsanleitung

Behringer

Behringer SYSTEM 55 Bedienungsanleitung

Behringer

Behringer NEUTRON Bedienungs- und Wartungsanleitung

Behringer

Behringer POLY D Montageanleitung

Behringer

Behringer EDGE Bedienungsanleitung

Behringer

Behringer Legendary 2500 Series Bedienungsanleitung

Beliebte Synthesizer Handbücher anderer Marken

Kawai

Kawai MP7 Technisches Handbuch

Joranalogue

Joranalogue Contour 1 Bedienungsanleitung

Full Bucket Music

Full Bucket Music Mono/Fury Bedienungsanleitung

Kawai

Kawai PH50 Bedienungsanleitung

IK Multimedia

IK Multimedia UNO Synth PRO X Bedienungsanleitung

Roland

Roland Gaia SH-01 Bedienungsanleitung

Roland

Roland GR-30 Bedienungsanleitung

Gotharman

Gotharman Gotharman's anAmoNo-box Bedienungsanleitung

Yamaha

Yamaha DX21 Bedienungsanleitung

QuStream

QuStream HDFS-550 Bedienungsanleitung

Modal Electronics

Modal Electronics ARGON8 Bedienungsanleitung

Roland

Roland GS-500 Bedienungsanleitung

Octave

Octave Cat SRM Bedienungsanleitung

Dreadbox

Dreadbox Murmux Initiate Bedienungsanleitung

neutral labs

neutral labs ELMYRA 2 Bedienungsanleitung

Waldorf

Waldorf KYRA Bedienungsanleitung

Tubbutec

Tubbutec Juno-66 Bedienungsanleitung

EFM

EFM VCADSR - 3510 Bedienungsanleitung