Behringer POLY D Bedienungsanleitung

page 1 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

Analog 4-Voice Polyphonic Synthesizer with

37 Full-Size Keys, 4 VCOs, Classic Ladder Filter,

LFO, BBD Stereo Chorus, Distortion, 32-Step

Sequencer and Arpeggiator

Synthesizers and Samplers

POLY D

User Support Bulletin

Calibration Procedure

Summary:

POWER LEDRegion B LEDsRegion A LEDs

CALIBRATION CHANNELS:

CHANNEL 1 — PITCH WHEEL MAX/MIN

CHANNEL 2 — PITCH WHEEL dead zone

CHANNEL 3 — MOD WHEEL MAX/MIN

CHANNEL 4 — AFTERTOUCH MIN

CHANNEL 5 — AFTERTOUCH MAX

Introduction

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

and the following recalibration procedures can be used to bring it back to its factory settings.

page 2 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 2 of 10

Synthesizers and Samplers

POLY D

Operation:

Start Calibration Routine

1. Press and hold button ”KYBD + STEP”, then power on POLY D.

2. When all the LEDs are running (during the rst 3 seconds after power on), press button“3” to start the

calibration routine.

3. Power LED will blink RED.

Follow all steps in the order in which they are presented.

Start PITCH WHEEL Calibration

1. Press button “1” to calibrate PITCH WHEEL.

2. Button “1” LED will light and region A LEDs will indicate current PITCH WHEEL position.

page 3 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 3 of 10

Synthesizers and Samplers

POLY D

Calibrate PITCH WHEEL Maximum Position

Move the PITCH WHEEL to its maximum position. Region A LEDs will show maximum position of PITCH WHEEL.

page 4 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 4 of 10

Synthesizers and Samplers

POLY D

Calibrate PITCH WHEEL Minimum Position

Move the PITCH WHEEL to its minimum position. Region A LEDs will show maximum position of PITCH WHEEL.

page 5 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 5 of 10

Synthesizers and Samplers

POLY D

Start PITCH WHEEL Dead Zone Calibration

1. First release PITCH WHEEL.

2. Press button “2” to calibrate PITCH WHEEL dead zone.

3. Button “2” LED will light on and region A LEDs will indicate current PITCH WHEEL position.

Calibrate PITCH WHEEL dead zone

Move the PITCH WHEEL within the dead zone where you don't feel the tension of the spring. This will ensure that no

pitch information is sent while pitch wheel is not being touched.

page 6 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 6 of 10

Synthesizers and Samplers

POLY D

Start MOD WHEEL Calibration

1. First move MOD WHEEL to its minimum position.

2. Press button “3” to calibrate MOD WHEEL.

3. Button “3” LED will light and Region A LEDs will indicate current MOD WHEEL position.

page 7 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 7 of 10

Synthesizers and Samplers

POLY D

Calibrate MOD WHEEL Maximum Position

Move the MOD WHEEL to its maximum position. Region A LEDs will show maximum position of MOD WHEEL.

page 8 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 8 of 10

Synthesizers and Samplers

POLY D

Calibrate MOD WHEEL Minimum Position

Move the MOD WHEEL to its minimum position. Region A LEDs will show minimum position of MOD WHEEL.

Start AFTER TOUCH Minimum Position Calibration

1. Press button“4” to calibrate AFTER TOUCH minimum position.

2. Button “4” LED will light on and region A LEDs will indicate current AFTER TOUCH value.

page 9 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 9 of 10

Synthesizers and Samplers

POLY D

Calibrate AFTER TOUCH Minimum Position

Apply a small pressure to any one of the keys (or multiple keys) or do not apply any pressure.

This will ensure that no after touch information is sent while keys are not being pressed.

Start AFTER TOUCH Maximum Position Calibration

1. Press button “5” to calibrate AFTER TOUCH maximum position.

2. Button “5” LED will light on and Region A LEDs will indicate current AFTER TOUCH value.

page 10 of 10

985-40000-01084 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 10 of 10

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global

Synthesizers and Samplers

POLY D

Calibrate AFTER TOUCH Maximum Position

Apply pressure to any one of the keys (or multiple keys) until AFTER TOUCH value stops increasing (Region A LEDs will

indicate current AFTER TOUCH value).

Calibration Complete.

Press SHIFT + STEP to conrm and save all calibration results. Region B LED will show calibration results. Relative LED

will light to indicate corresponding channel is calibrated. Otherwise it may be a failed calibration.

NOTE: Press SHIFT + KYBD will cancel all calibration and return to normal mode.

TIPS:

A. You can calibrate only one of the channels (1-3) at a time.

B. For channel 4 and 5, you have to calibrate both of them simultaneously.

End of Procedure

Andere Handbücher für POLY D

Inhaltsverzeichnis

Andere Behringer Synthesizer Handbücher

Behringer

Behringer PRO-VS MINI Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer SYSTEM 15 Bedienungsanleitung

Behringer

Behringer NEUTRON Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer 962 SEQUENTIAL SWITCH Bedienungsanleitung

Behringer

Behringer 110 VCO/VCF/VCA Bedienungsanleitung

Behringer

Behringer ODYSSEY Bedienungsanleitung

Behringer

Behringer Legendary 2500 Series Bedienungsanleitung

Behringer

Behringer POLY D Montageanleitung

Behringer

Behringer CRAVE Montageanleitung

Behringer

Behringer SYSTEM 55 Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer K-2 Bedienungsanleitung

Behringer

Behringer MODEL D Bedienungsanleitung

Behringer

Behringer D A-440 Montageanleitung

Behringer

Behringer PRO-1 Bedienerhandbuch

Behringer

Behringer PRO-1 Bedienungsanleitung

Behringer

Behringer CRAVE Bedienungsanleitung

Behringer

Behringer CAT Referenzhandbuch

Behringer

Behringer MS-1-BK Handbuch

Behringer

Behringer NEUTRON Bedienungsanleitung

Behringer

Behringer SYSTEM 55 Bedienungsanleitung

Beliebte Synthesizer Handbücher anderer Marken

Kawai

Kawai MP7 Technisches Handbuch

Joranalogue

Joranalogue Contour 1 Bedienungsanleitung

Full Bucket Music

Full Bucket Music Mono/Fury Bedienungsanleitung

Kawai

Kawai PH50 Bedienungsanleitung

IK Multimedia

IK Multimedia UNO Synth PRO X Bedienungsanleitung

Roland

Roland Gaia SH-01 Bedienungsanleitung

Roland

Roland GR-30 Bedienungsanleitung

Gotharman

Gotharman Gotharman's anAmoNo-box Bedienungsanleitung

Yamaha

Yamaha DX21 Bedienungsanleitung

QuStream

QuStream HDFS-550 Bedienungsanleitung

Modal Electronics

Modal Electronics ARGON8 Bedienungsanleitung

Roland

Roland GS-500 Bedienungsanleitung

Octave

Octave Cat SRM Bedienungsanleitung

Dreadbox

Dreadbox Murmux Initiate Bedienungsanleitung

neutral labs

neutral labs ELMYRA 2 Bedienungsanleitung

Waldorf

Waldorf KYRA Bedienungsanleitung

Tubbutec

Tubbutec Juno-66 Bedienungsanleitung

EFM

EFM VCADSR - 3510 Bedienungsanleitung