Behringer MonoPoly Bedienungsanleitung

page 1 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

Analog 4-Voice Polyphonic Synthesizer with

37 Full-Size Keys, 4 VCOs, VCF,

2 LFOs, 2 Envelopes, Sync and Cross

Modulation and Arpeggiator

Synthesizers and Samplers

MONOPOLY

Service Support Bulletin

History

Requirement

This calibration function is only available on 1.0.5 or later version rmware.

Date Version Note

2021-03-03 Rev0 Initial version

How to start calibration

Power o MONOPOLY rst.

Long press and hold button HOLD and POLY simultaneously.

page 2 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 2 of 6

Synthesizers and Samplers

MONOPOLY

Cycle power on MONOPOLY.

Wait approximately 2 seconds until power LED blinking slowly.

Release all buttons.

There are 3 sub calibration menus. Press the corresponding button to enter the sub menu.

Tip:

You can only calibrate one channel at a time. Ignore the other channels if you don't want to change them.

Sub Calibration Menu

(Channel) Buttons Function Button LEDs VCO LEDs

1MONO UNISON PITCH WHEEL MAX/MIN indicates PITCH WHEEL position VCO1 LED on

2POLY UNISON PITCH WHEEL dead zone indicates PITCH WHEEL dead zone VCO2 LED on

3POLYPOLY MOD WHEEL MAX/MIN indicates MOD WHEEL position VCO3 LED on

page 3 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 3 of 6

Synthesizers and Samplers

MONOPOLY

Calibration Procedure

Follow all steps in the order they are presented.

Start BEND WHEEL Calibration

Press button MONO UNISON, then VCO1 LED will illuminate.

Calibrate BEND WHEEL maximum position

Move the BEND WHEEL to its maximum position.

page 4 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 4 of 6

Synthesizers and Samplers

MONOPOLY

Calibrate BEND WHEEL minimum position

Move the BEND WHEEL to its minimum position.

Start BEND WHEEL dead zone calibration

This step is to ensure that no bend information is sent while bend wheel is not being touched.

1. Make sure the BEND WHEEL is released and returned to its center position before further operation.

2. Press button POLY UNISON, then VCO2 LED will light up.

page 5 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 5 of 6

Synthesizers and Samplers

MONOPOLY

Start MG1 WHEEL Calibration

Press button POLY POLY, then VCO3 LED will illuminate.

Calibrate MG1 WHEEL maximum position

Move the MG1 WHEEL to its maximum position.

Calibrate BEND WHEEL dead zone

Move the BEND WHEEL within the dead zone where you don't feel the tension of the spring.

page 6 of 6

985-40000-01200 Rev.A

2022-04-21

Condential, for internal use only. Not to be reproduced.

page 6 of 6

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of

Synthesizers and Samplers

MONOPOLY

End of Procedure

Complete calibration

Short press HOLD + EFFECTS will conrm and save all calibration result. If successful, all BUTTON LEDs will blink at the

same time for a while. Otherwise, it may be a failed calibration.

NOTE: Press HOLD + MONO CHORD will cancel all calibration and return back to normal mode.

Calibrate MG1 WHEEL minimum position

Move the MG1 WHEEL to its minimum position.

Andere Handbücher für MonoPoly

Inhaltsverzeichnis

Andere Behringer Synthesizer Handbücher

Behringer

Behringer PRO-VS MINI Bedienungsanleitung

Behringer

Behringer 962 SEQUENTIAL SWITCH Bedienungsanleitung

Behringer

Behringer MS-1-BK Handbuch

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer Victor Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer CRAVE Bedienungsanleitung

Behringer

Behringer PRO-800 Bedienungsanleitung

Behringer

Behringer NEUTRON Referenzhandbuch

Behringer

Behringer SYSTEM 15 Bedienungsanleitung

Behringer

Behringer CRAVE Montageanleitung

Behringer

Behringer NEUTRON Bedienungsanleitung

Behringer

Behringer 112 DUAL VCO Bedienungsanleitung

Behringer

Behringer DeepMind 6 Bedienungsanleitung

Behringer

Behringer SYSTEM 55 Bedienungsanleitung

Behringer

Behringer CAT Referenzhandbuch

Behringer

Behringer MonoPoly Montageanleitung

Behringer

Behringer VOCODER VC340 Bedienungsanleitung

Behringer

Behringer NEUTRON Bedienungsanleitung

Behringer

Behringer FILTAMP MODULE 1006 Bedienungsanleitung

Behringer

Behringer PRO-1 Bedienerhandbuch

Behringer

Behringer TORO Bedienungsanleitung

Behringer

Behringer UB-Xa Bedienungsanleitung

Behringer

Behringer SYSTEM 100 172 PHASE SHIFTER/DELAY/LFO Bedienungsanleitung

Beliebte Synthesizer Handbücher anderer Marken

Kawai

Kawai MP7 Technisches Handbuch

Joranalogue

Joranalogue Contour 1 Bedienungsanleitung

Full Bucket Music

Full Bucket Music Mono/Fury Bedienungsanleitung

Kawai

Kawai PH50 Bedienungsanleitung

IK Multimedia

IK Multimedia UNO Synth PRO X Bedienungsanleitung

Roland

Roland Gaia SH-01 Bedienungsanleitung

Roland

Roland GR-30 Bedienungsanleitung

Gotharman

Gotharman Gotharman's anAmoNo-box Bedienungsanleitung

Yamaha

Yamaha DX21 Bedienungsanleitung

QuStream

QuStream HDFS-550 Bedienungsanleitung

Modal Electronics

Modal Electronics ARGON8 Bedienungsanleitung

Roland

Roland GS-500 Bedienungsanleitung

Octave

Octave Cat SRM Bedienungsanleitung

Dreadbox

Dreadbox Murmux Initiate Bedienungsanleitung

neutral labs

neutral labs ELMYRA 2 Bedienungsanleitung

Waldorf

Waldorf KYRA Bedienungsanleitung

Tubbutec

Tubbutec Juno-66 Bedienungsanleitung

EFM

EFM VCADSR - 3510 Bedienungsanleitung