Behringer K-2 Bedienungsanleitung

page 1 of 2

985-40000-01088 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

Analog and Semi-Modular Synthesizer with

Dual VCOs, Ring Modulator, External

Signal Processor, 16-Voice Poly Chain and

Eurorack Format

Synthesizers and Samplers

K-2

User Support Bulletin

Calibration Procedure

Set the K-2 controls as shown.

Make sure your K-2 has been powered on for more than 30 minutes, and that it is in a place where the temperature will

not change drastically while performing the calibration.

Follow all steps in the order in which they are presented.

Introduction

The unit is carefully calibrated at the factory. The performance may change over time or due to environmental changes,

and the following recalibration procedures can be used to bring it back to its factory settings.

page 2 of 2

985-40000-01088 Rev.A

2021-02-03

Condential, for internal use only. Not to be reproduced.

page 2 of 2

Condential, for internal use only. Not to be reproduced.

Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.

Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik,

Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global

Synthesizers and Samplers

K-2

VCO PITCH Calibration

Press and hold “TRIG SW” while powering up to enter the testing mode. (In this mode, the ON LED will blink yellow).

The K-2 has an internal calibration routine to calibrate the pitch of the VCO.

Press and hold “TRIG SW,” and then set the “FILTER1/2” switch. The ON LED will light yellow, indicating that the

VCO calibration has begun.

Wait until the ON LED changes color:

- Green indicates that the calibration was successful.

- Red indicates calibration failure. If this occurs, turn o the power and repeat from Step1.

Restart the unit.

End of Procedure

Inhaltsverzeichnis

Andere Behringer Synthesizer Handbücher

Behringer

Behringer NEUTRON Referenzhandbuch

Behringer

Behringer MonoPoly Bedienungsanleitung

Behringer

Behringer PRO-1 Bedienungsanleitung

Behringer

Behringer 2600 Bedienungsanleitung

Behringer

Behringer SYSTEM 15 Bedienungsanleitung

Behringer

Behringer TD-3 Bedienungsanleitung

Behringer

Behringer POLY D Montageanleitung

Behringer

Behringer MODEL D Bedienungsanleitung

Behringer

Behringer MonoPoly Montageanleitung

Behringer

Behringer K-2 Bedienungsanleitung

Behringer

Behringer NEUTRON Bedienungs- und Wartungsanleitung

Behringer

Behringer CAT Referenzhandbuch

Behringer

Behringer CRAVE Montageanleitung

Behringer

Behringer 914 Fixed Filter Bank Bedienungsanleitung

Behringer

Behringer CRAVE Bedienungsanleitung

Behringer

Behringer PRO-VS MINI Bedienungsanleitung

Behringer

Behringer DEEPMIND 12 Bedienungsanleitung

Behringer

Behringer FILTAMP MODULE 1006 Bedienungsanleitung

Behringer

Behringer 962 SEQUENTIAL SWITCH Bedienungsanleitung

Behringer

Behringer SYSTEM 55 Bedienungsanleitung

Behringer

Behringer MODEL D Bedienungsanleitung

Behringer

Behringer PRO-800 Bedienungsanleitung

Behringer

Behringer PRO-1 Bedienungsanleitung

Behringer

Behringer UB-Xa Bedienungsanleitung

Beliebte Synthesizer Handbücher anderer Marken

Kawai

Kawai MP7 Technisches Handbuch

Joranalogue

Joranalogue Contour 1 Bedienungsanleitung

Full Bucket Music

Full Bucket Music Mono/Fury Bedienungsanleitung

Kawai

Kawai PH50 Bedienungsanleitung

IK Multimedia

IK Multimedia UNO Synth PRO X Bedienungsanleitung

Roland

Roland Gaia SH-01 Bedienungsanleitung

Roland

Roland GR-30 Bedienungsanleitung

Gotharman

Gotharman Gotharman's anAmoNo-box Bedienungsanleitung

Yamaha

Yamaha DX21 Bedienungsanleitung

QuStream

QuStream HDFS-550 Bedienungsanleitung

Modal Electronics

Modal Electronics ARGON8 Bedienungsanleitung

Roland

Roland GS-500 Bedienungsanleitung

Octave

Octave Cat SRM Bedienungsanleitung

Dreadbox

Dreadbox Murmux Initiate Bedienungsanleitung

neutral labs

neutral labs ELMYRA 2 Bedienungsanleitung

Waldorf

Waldorf KYRA Bedienungsanleitung

Tubbutec

Tubbutec Juno-66 Bedienungsanleitung

EFM

EFM VCADSR - 3510 Bedienungsanleitung