Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Installing MAMMUTHUS SWITCH

Published on 01 01/2020

Technical Support

https://hirschmann-it.support.belden.com

User Manual

Installation

MAMMUTHUS CORE LAYER SWITCH –

MTS2948X-6Q-A

MAMMUTHUS POWER MODULE – MTM2900-PSU250

MAMMUTHUS FAN MODULE – MTM2900-FAN

MAMMUTHUS SWITCH

Even if not specifically stated, the copyrighted trademark names in this manual shall not be deemed free of

charge in the sense of the trademark and trade name protection act and thus freely available to anyone.

be prohibited from being reproduced, copied, translated or converted into any electronic media or

machine-scannable form, except in the case that you make a copy of the software for your own use.

The performance characteristics described herein shall be binding only upon the express consent of the parties

at the time of signing the contract. This paper is produced by Belden within its capacity. Belden reserves the right

to change the contents of this manual without prior notice. Belden does not guarantee the correctness or

accuracy of the information in this manual.

Belden shall not be liable for damages caused by the use of network components or related operating software.

And the conditions of use specified in the license contract are referred to in this manual.

You may access the latest version of this manual at the product website of Hirschmann IT:

Hirschmann-it.support.belden.com.

Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

Contents

Safety guidelines 5

About the manual 12

Figure 13

1 Description 14

1.1 General equipment description 14

1.2 Equipment name and product code 16

1.2.1 Basic device 16

1.2.2 Power module 16

1.2.3 Fan module 16

1.3 Equipment view 17

1.3.1 MTS2948X-6Q-A 17

1.3.2 Power module 19

1.3.3 Fan module 20

1.4 Power supply 21

1.5 Ethernet port 22

1.5.1 10 Gbit/s F/O port 22

1.5.2 40 Gbit/s F/O port 22

1.5.3 Out-of-band management port 23

1.6 Display unit 24

1.6.1 Equipment state 24

1.6.2 Port Status 26

1.7 Management interface 27

1.7.1 DC0 interface (external management) 27

1.7.2 USB interface 27

2 Installation 28

2.1 Unpack the box for inspection 28

2.2 Install power module (optional) 28

2.3 Install equipment and ground 29

4 Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

2.4 Install SFP transceiver (optional) 30

2.5 Operate equipment 32

2.6 Connect data cable 32

2.7 Fill in the Device Label 32

3 Make basic settings 33

4 Monitor ambient air temperature 34

5 Maintenance and repair 35

6 Remove 36

6.1 Remove power module 36

6.2 Remove fan module 36

6.3 Remove SFP transceiver 37

6.4 Remove device 38

7 Technical data 39

7.1 General technical data 39

7.2 Size diagram 41

7.3 EMC and immunity 44

7.4 Network range 47

7.5 Power consumption / power output 47

8 Delivery item, order number and accessories 48

9 Basic technical standards 49

A More support 51

Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

Safety guidelines

Warning

Uncontrolled machine action

To avoid uncontrolled machine action due to data loss, configure all data transfer

devices separately.

Before starting any machine controlled by data transfer, be sure to complete the

configuration of all data transfer devices.

Failure to comply with t

hese guidelines may result in death, serious injury or

equipment damage.

 General safety guidelines

Hot-line work is required for the equipment. Improper use of the equipment

may result in personal injury or great destruction of property. The proper and

safe operation of the equipment depends on proper handling during

transportation, reasonable storage and installation, as well as careful

establishment and strict adherence to the operation and maintenance

procedures.

 Please read this manual as well as safety guidelines and warnings before

connecting any cable.

 Only operate the equipment without any damaged components.

 Make sure there is no component to be repaired in the equipment. In case

of any damage or failure to the equipment, switch off the power and return

the equipment to Belden for inspection.

 Qualification requirements for operators

 Only qualified personnel are allowed to operate the equipment.

Qualified personnel have the following characteristics:

 They shall receive appropriate training. Training and required practical

knowledge and experience are prerequisites to be qualified for product

operation. Only when these prerequisites are met can operators perform

grounding and labeling operations on circuits, equipment and systems in

accordance with current safety technical standards.

 Qualified personnel shall be aware that there is danger in their work.

 Qualified personnel shall know well how to deal with these hazards to

reduce risks posed to themselves and others.

 Qualified personnel shall receive training on a regular basis.

6 Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

 Correct use

Use the equipment only for the purposes specified in the catalog and

technical instructions. Only external devices and components recommended

and permitted by the manufacturer can be used to operate the equipment.

The correct and safe operation of this product depends on the correct

operation, storage, assembly and installation during transport, as well as

careful operation and maintenance procedures.

 National and international safety regulations

Carry out validation to ensure that electrical installations comply with

applicable local or national safety regulations.

 Wire connection requirements

Always make sure that all requirements listed are met before connecting the

wires.

The requirements bel

ow shall apply without limitation:

 The wires are voltage free.



The cables used meet the temperature range required for a particular purpose.

 First, connect the ground screw on the back of the equipment to the protective conductor before setting up

other connections. When to remove connections, the protective conductor shall be the last to be removed.

 Do not power up the equipment during installation.

 Requirements for North America:

Use 60 / 75 ° C (140 / 167 ° F) or 75 ° C (167 ° F) c

opper (Cu) wires only.

Table 1: Wire connection requirements

 Power voltage connection requirements

Device Model

The requirements below shall apply without limitation:

All Models

Meet

all

of the following requirements

 The supply voltage shall be consistent with the specified value on the equipment

nameplate.

 The power supply shall conform to overvoltage category I or II.

 The power supply shall be equipped with an easy-to-operate disconnector (such as a

switch or plug).

 The disconnector shall be clearly marked, so that in an emergency, the operator knows

at a glance the correspondence between the disconnector and the power cable.



When to connect a power supply voltage with a protective conductor: first connect the

protective conductor, and then the power supply voltage. If the equipment contains such

a second power supply voltage connection module: first connect the protective

conductor, and then the power supply voltage.

 Supply with DC voltage:

Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

 Power cord diameter at the power supply voltage input shall be at least 1mm² (North

America: AWG16). Supply with AC voltage:

 Power cord diameter at the power supply voltage input shall be at least 0.75 mm² (North

America: AWG18).

 The cross section of the grounding conductor shall be the same as or larger than that of

the power cord.

 Power cables suitable for voltage, current and physical loads shall be used.

 The external fuse shall be installed in the conductor at the non-spot position.

Table 2: Power voltage connection requirements

8 Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

Special conditions for safe use

 Install the basic equipment and modules in a suitable enclosure based on

specific environmental conditions to provide at least IP54 protection

according to the requirements of EN 60529.

 Take measures to prevent instantaneous interference from exceeding

140% of the rated voltage at the voltage input.

 Shield grounding

The shield grounding module of the twisted-pair cable shall be connected to

the front panel as a conductor.

When connecting a cable segment with a conductive shield braid, pay

attention to the possible short circuit.

 ESD guide

These modules are equipped with electrostatic sensitive components.

If the connection is touched, these sensitive components may be damaged or

their service life shortened by electric field or charge balance effects.

You may find information about electrostatic hazard components in DIN EN

61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).

Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

 Equipment enclosure

Only technicians authorized by the manufacturer are allowed to open the

enclosure.

 Keep vents open to ensure good air circulation.

 Ensure a minimum of 3.94 inches (10 cm) of space in front of the

enclosure vent.

 Do not touch the enclosure during operation or shortly after shutting down

the equipment. Hot surfaces may cause injury.

 Install the equipment horizontally in the cabinet or vertically on a flat

surface.

Do not place the equipment on the desktop for operation. See Page 30 for

details of “Equipment installation and grounding”.

 Operate the equipment at the maximum ambient air temperature and in

stacking: when to install the equipment, make sure that there is at least

one available rack space (approx. 5 cm) above the equipment to allow

heat to escape through the enclosure of the equipment.

 If you operate the equipment in 19” switch cabinet: install the slide / rails

to support the weight of the equipment.

 Installation site requirements

The equipment can only be operated at the specified ambient temperature -

the ambient air temperature at a distance of 2 inches (5 cm) from the

equipment - with relative humidity.

 When selecting the installation position, be sure to comply with the

climate thresholds set forth in the technical data.

 Please use the equipment in the environment where the maximum

pollution level conforms to the technical data.

10 Installing MAMMUTHUS

SWITCH

Published on 01

01/2020

 CE mark

Marked equipment shall comply with the European directives below:

Device Model Instruction

All Models

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction of the use of

certain hazardous substances in electrical and electron.

All Models 2014/30/EU (EMC)

Directive of the European Parliament and of the Council on electromagnetic

compatibility among standardization members.

Please submit the EU compliance statement to the authorities at the following

address in accordance with the above EU directives:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.belden.com

Warning! As Class A equipment, it may cause interference to the living area. In

such case, the operator may need to take appropriate actions.

Warning! When Ethernet cables are used in industrial environments, they must

be shielded.

Note: It is required to strictly comply with the assembly guidelines provided in

these guidelines to observe EMC thresholds.

Andere Handbücher für HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden Hirschmann MACH4002 Series Bedienungsanleitung

Belden

Belden Hirschmann RED25 Series Bedienungsanleitung

Belden

Belden Hirschmann MACH1000 Series Bedienungsanleitung

Belden

Belden Hirschmann MACH1040 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH4002-48+4G Bedienungsanleitung

Belden

Belden HIRSCHMANN SPIDER II Bedienungsanleitung

Belden

Belden HIRSCHMANN MSP30 Bedienungsanleitung

Belden

Belden Hirschmann SPIDER II 8TX Bedienungsanleitung

Belden

Belden MAMMUTHUS MTM2800-PSU120 Bedienungsanleitung

Belden

Belden HIRSCHMANN OCTOPUS OS3 Bedienungsanleitung

Belden

Belden HIRSCHMANN OCTOPUS OS20 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Bedienungsanleitung

Belden

Belden lumberg automation 0960 IOL 3816-001 Bedienungsanleitung

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden Grass Valley Kayenne Beilage

Belden

Belden HIRSCHMANN HiOS-2A Bedienungsanleitung

Belden

Belden Hirschmann DRAGON MACH Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 100 Series Bedienungsanleitung

Belden

Belden Grass Valley K-Frame Anleitung zur Verwendung

Belden

Belden HIRSCHMANN PTN-CSM310-A Bedienungsanleitung

Belden

Belden HIRSCHMANN RSP20 Bedienungsanleitung

Belden

Belden Telecast Fiber Systems THOR-SLG Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden Hirschmann RS20 U Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch