Belden Hirschmann MICE MS20 Bedienungsanleitung

Installation MS20/MS30

Release

03/2023

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial ETHERNET Switch MICE

MS20/MS30

MICE MS20 MICE MS30

24.3.23 Installation MS20/MS30

Release

03/2023

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at:

https://www.doc.hirschmann.com

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Contents

Important information 5

Safety instructions 7

About this Manual 22

Key 23

1 Description 24

1.1 General device description 24

1.2 Device name and product code 26

1.3 Description of the device variants 27

1.3.1 Number of ports and connections 28

1.3.2 Media modules 32

1.3.3 Digital I/O Module MM24 36

1.3.4 MB20 extender module 36

1.3.5 SFP Transceiver 37

1.4 Ethernet ports 37

1.4.1 10/100/1000 Mbit/s twisted pair port 37

1.4.2 10/100 Mbit/s twisted pair port 37

1.4.3 10/100 Mbit/s PoE port 38

1.4.4 1000 Mbit/s F/O port 38

1.4.5 100 Mbit/s F/O port 38

1.4.6 Pin assignments 39

1.5 AUI port 40

1.6 Display elements 41

1.6.1 Device Status 42

1.6.2 Display status 43

1.6.3 Port status 44

2 Installation 46

2.1 Checking the package contents 46

2.2 Installing media modules 47

2.3 Filling out and attaching labels 47

2.4 Installing an SFP transceiver (optional) 49

4Installation MS20/MS30

Release

03/2023

2.5 Adjusting the DIP switch settings on the basic module (4-pin

DIP switch) 49

2.6 Adjusting the DIP switch settings on the MS20/MS30-...E...

basic module (3-pin DIP switch) 51

2.7 Adjusting the DIP switch settings on the

MM20-A8A89999SAHH media module 53

2.8 Connecting the MM22-T1T1T1T1 PoE media module 53

2.9 Terminal block for supply voltage and signal contact 54

2.9.1 Supply voltage 55

2.9.2 Signal contacts 55

2.10 Connecting the terminal blocks, start-up procedure 55

2.10.1 Terminal blocks on MS20/MS30-...A... and MS20/

MS30-...C... 56

2.10.2 Terminal block on MS20/MS30-...E... 57

2.10.3 Operating the device 57

2.11 Installing and grounding the device 58

2.11.1 Installing the device onto the DIN rail 58

2.11.2 Grounding the device 59

2.12 Connecting data cables 59

2.12.1 Twisted Pair ports 59

2.12.2 Optical fiber ports 60

2.13 Assembly of the MB20 extender module 60

2.14 Defining the meaning of the display LEDs 60

3 Making basic settings 61

3.1 First login (Password change) 63

4 Maintenance and service 64

5Disassembly 65

5.1 Removing the device 65

5.2 Removing an SFP transceiver (optional) 66

6 Technical data 67

A Further support 89

Installation MS20/MS30

Release

03/2023 5

Important information

Note: Read these instructions carefully, and familiarize yourself with the

device before trying to install, operate, or maintain it. The following notes may

appear throughout this documentation or on the device. These notes warn of

potential hazards or call attention to information that clarifies or simplifies a

procedure.

Symbol explanation

This is a general warning symbol. This symbol alerts you to

potential personal injury hazards. Observe all safety notes that

follow this symbol to avoid possible injury or death.

If this symbol is displayed in addition to a safety instruction of the

type “Danger” or “Warning”, it means that there is a danger of

electric shock and failure to observe the instructions will

inevitably result in injury.

This symbol indicates the danger of hot surfaces on the device.

In connection with safety instructions, non-observance of the

instructions will inevitably result in injuries.

DANGER

DANGER draws attention to an immediately dangerous situation, which will

inevitably result in a serious or fatal accident if not observed.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a possible danger which, if not avoided, may result in

minor injuries.

6Installation MS20/MS30

Release

03/2023

NOTICE

NOTICE provides information about procedures that do not involve the risk

of injury.

Installation MS20/MS30

Release

03/2023 7

Safety instructions

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

Supply voltage

The devices are designed for operation with Safety Extra-low Voltage

(SELV). Connect only SELV circuits with voltage restrictions according to

IEC 60950-1 or ES1 according to IEC/EN 62368-1 to the supply voltage

connections and to the signal contacts.

The supply voltage is electrically isolated from the housing.

Use undamaged parts.

For power supply via DC voltage: All following prerequisites are

fulfilled:

There are fuses suitable for DC voltage in the positive conductors

of the supply lines, or the voltage sources are appropriately current-

limited. Regarding the properties of this fuse: See “General

technical data” on page 67.

The negative conductors of the voltage inputs are on ground

potential.

For power supply via AC voltage: All following prerequisites are

fulfilled:

There are fuses in the supply lines, or the voltage sources are

appropriately current-limited. Regarding the properties of this fuse:

See “General technical data” on page 67.

The power sources are electrically isolated from the ground

potential.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

8Installation MS20/MS30

Release

03/2023

Relevant for North America:

The device may only be connected to a Class 2 supply voltage that

fulfills the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Relevant for North America: For use in Class 2 circuits.

Only use copper wire/conductors of class 1, 75 °C (167 °F).

Start connecting the electrical wires only if all the above safety

requirements are fulfilled.

Use in Hazardous Locations

Relevant for North America for modules certified for Hazardous

Locations:

This equipment is suitable for use in Class 1, Division 2, Groups A, B, C

and D or Non-Hazardous (unclassified) locations only.

Make sure that peripheral devices are suitable for the application

environment. The wiring for the voltage supply and for the inputs and

outputs (I/O) must adhere to the wiring regulations for Class 1, Division 2

[article 501(b) of the National Electrical Code (USA), NFPA 70] and to the

applicable statutory regulations.

Note: Observe the control drawing (document number 000160011DNR)

on the following pages.

Avertissement - Risque d'explosion - Ne pas débrancher tant que le

circuit est sous tension à moins que l'emplacement soit connu pour ne

contenir aucune concentration de gaz inflammable.

Avertissement - Risque d'explosion - La substitution de tout composant

peut rendre ce matériel incompatible pour une utilisation en classe I,

division 2.

Installation MS20/MS30

Release

03/2023 9

CONTROL DRAWING

for Industrial ETHERNET Rail Switch MS20 and MS30 devices 943-435-999

according to Class I Division 2 Hazardous Locations

Version: 4 Document No.: 000160011DNR Pa

e 1/3

Ordinary Location,

Non-Hazardous Area,

non-explosive atmosphere

WARNING! The USB connection and the V.24

Interface connection are for temporary

connection only, for maintenance use. Do not

use, connect or disconnect unless the area is

known to be non-hazardous. Connection or

disconnection in an explosive atmosphere could

result in an explosion!

Relay

Rela

The ground connector must be

at least the same wire size

(mm² or AWG) as the supply

conductors.

Power Supply range “C” (P1, P2 Redundant)

18 – 60 V DC;

4.0 – 1.2 A; max. 72 W

Relay contacts:

Equipment with non-incendive field wiring

parameters.

Polarity is not relevant.

THE RELAY TERMINALS ARE DEPENDENT

UPON THE FOLLOWING ENTITY

PARAMETERS: 1) 2)

Temperature Code: T4

Ambient Temperature rating:

Ta: 0 °C to +60 °C for “S” types

Ta: -40 °C to +70 °C for “T” or “E” types

– refer to the type designation on the device

(Position 10 of nomenclature: “Temperature range”).

MS20/30 switch basic module

with voltage range type “C”

Class I, Division 2,

Groups A, B, C, D

Hazardous Location

UiIiCiLi

30 V 90 mA 2 nF 1 µH

10 Installation MS20/MS30

Release

03/2023

CONTROL DRAWING

for Industrial ETHERNET Rail Switch MS20 and MS30 devices 943-435-999

according to Class I Division 2 Hazardous Locations

Version: 4 Document No.: 000160011DNR Pa

e 2/3

WARNING! The USB connection and the V.24

Interface connection are for temporary

connection only, for maintenance use. Do not

use, connect or disconnect unless the area is

known to be non-hazardous. Connection or

disconnection in an explosive atmosphere could

result in an explosion!

Relay

Power Supply range “A” (P1, P2 Redundant)

18 – 32 V DC;

4.0 – 2.25 A; max. 72 W

Temperature Code: T4

Ambient Temperature rating:

Ta: 0 °C to +60 °C for “S” types

Ta: -40 °C to +70 °C for “T” or “E” types

– refer to the type designation on the device

(Position 10 of nomenclature: “Temperature range”).

Class I Division 2

Groups A, B, C, D

Hazardous Location

Ordinary Location,

Non-Hazardous Area,

non-explosive atmosphere

The ground connector must be

at least the same wire size

(mm² or AWG) as the supply

conductors.

MS20/30 switch basic module

with voltage range type “A”

Relay contacts:

Equipment with non-incendive field wiring

parameters.

Polarity is not relevant.

THE RELAY TERMINALS ARE DEPENDENT

UPON THE FOLLOWING ENTITY

PARAMETERS: 1) 2)

UiIiCiLi

30 V 90 mA 2 nF 1 µH

Andere Handbücher für Hirschmann MICE MS20

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden grass valley KULA AV Bedienungsanleitung

Belden

Belden MAMMUTHUS MTM2800-PSU120 Bedienungsanleitung

Belden

Belden HIRSCHMANN HiOS-2A Bedienungsanleitung

Belden

Belden HIRSCHMANN EESX Series Kurzanleitung zur Einrichtung

Belden

Belden Thinklogical TLX48 Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 100 Series Bedienungsanleitung

Belden

Belden Hirschmann OCTOPUS 8TX PoE-EEC Bedienungsanleitung

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A Bedienungsanleitung

Belden

Belden HIRSCHMANN BRS20 Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH4002-48+4G Bedienungsanleitung

Belden

Belden grass valley SIRIUS 800 Series Benutzerhandbuch

Belden

Belden Grass Valley K-Frame Anleitung zur Verwendung

Belden

Belden Hirschmann HiOS-2S Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden ThinkLogical TLX12 Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Belden

Belden Hirschmann SPIDER 8TX EEC Bedienungsanleitung

Belden

Belden Hirschmann MACH4002 Series Bedienungsanleitung

Belden

Belden grass valley MASTERPIECE 12G-SDI Bedienungsanleitung

Belden

Belden HIRSCHMANN RSPE 30 Bedienungsanleitung

Belden

Belden HIRSCHMANN SPIDER II Bedienungsanleitung

Belden

Belden HIRSCHMANN MACH 4000 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung