Belden HIRSCHMANN RSPE 30 Bedienungsanleitung

Installation RSPE 30/32/35/37

Release

08/2014

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Rail Switch Power Enhanced

RSPE 30/32/35/37

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Installation RSPE 30/32/35/37 040 045-001-08-0814 - 29.07.2014

Installation RSPE 30/32/35/37

Release

08/2014 3

Contents

Safety instructions 5

About this manual 11

Key 11

1 Description 12

1.1 General description 12

1.2 Device name and product code 13

1.3 Combination options 17

1.4 Device views 18

1.4.1 Front view 18

1.4.2 Rear view 19

1.5 Power supply 20

1.5.1 Working voltage characteristic value K9 20

1.5.2 Working voltage with the characteristic value KK 20

1.5.3 Working voltage characteristic value CC 20

1.5.4 Working voltage with the characteristic value PP 20

1.6 Ethernet ports 21

1.6.1 Gigabit combo port 22

1.6.2 10/100 Mbit/s twisted pair port 23

1.6.3 100 Mbit/s F/O port (optional) 24

1.6.4 Support of PoE and PoE+ 25

1.7 Display elements 26

1.7.1 Device state 26

1.7.2 Media module status 27

1.7.3 Port state 28

1.8 Management interfaces 30

1.8.1 V.24 interface (external management) 30

1.8.2 SD card interface 30

1.8.3 USB interface 31

1.9 Signal contact 31

2 Installation 32

2.1 Unpacking and checking the content of the package 32

2.2 Installing the SD card (optional) 32

2.3 Mounting a dummy panel or a media module 33

2.3.1 Mounting a dummy panel 33

2.3.2 Mounting a media module 33

4Installation RSPE 30/32/35/37

Release

08/2014

2.4 Installing and grounding the device 34

2.4.1 Installing the device onto the DIN rail 34

2.4.2 Grounding the device 35

2.5 Installing an SFP transceiver (optional) 36

2.6 Connecting the terminal blocks 36

2.6.1 Working voltage characteristic value K9 37

2.6.2 Working voltage with the characteristic value KK 38

2.6.3 Working voltage characteristic value CC 39

2.6.4 Working voltage with the characteristic value PP 40

2.6.5 Signal contact 41

2.7 Operating the device 42

2.8 Connecting data cables 42

2.9 Filling out the inscription label 42

3 Making basic settings 43

4 Upgrading Software 44

5 Monitoring the ambient air temperature 45

6 Maintenance and service 46

7Disassembly 47

7.1 Removing the device 47

7.2 Removing an SFP transceiver (optional) 48

7.3 Removing a media module (optional) 48

8 Technical data 49

A Further Support 61

Installation RSPE 30/32/35/37

Release

08/2014 5

Safety instructions

General safety instructions

You operate this device with electricity. The proper and safe operation of

this device depends on proper handling during transportation, proper

storage and assembly, and conscientious operation and maintenance

procedures. Improper use of this device is associated with the risk of

personal injury or property damage.

Read this documentation as well as the safety instructions and

warnings before connecting any cables.

Never start operation with damaged components.

The device does not contain any service components. If the device is

not functioning correctly, or if it is damaged, turn off the power supply

and return the device to Hirschmann for inspection.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

See “Technical data” on page 49.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RSPE 30/32/35/37

Release

08/2014

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected

to the ground connector on the front panel as a conductor.

Working voltage

The working voltage is connected to the chassis through protective

elements exclusively.

Connect only a working voltage that corresponds to the type plate of

your device.

Only for device variants featuring working voltage with the

characteristic value K9 or KK:

See “Device name and product code” on page 13.

Every time you connect the electrical conductors, make sure that the

following requirements are met:

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

The electrical wires are voltage-free.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse: See “General technical data”

on page 49.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential. Otherwise, a fuse is

also located in the neutral conductor.

Regarding the properties of this fuse: See “General technical data”

on page 49.

Supply with AC voltage:

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the working voltage input.

Installation RSPE 30/32/35/37

Release

08/2014 7

Supply with DC voltage:

The wire diameter of the power supply cable is at least 1 mm²

(North America: AWG16) on the working voltage input.

The cross-section of the protective conductor is the same size as

or bigger than the cross-section of the power supply cables.

The power supply cables used are permitted for the temperature

range required by the application case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires only if all the above safety

requirements are fulfilled.

Only for device variants featuring working voltage with the

characteristic value C or PP:

See “Device name and product code” on page 13.

Every time you connect the electrical conductors, make sure that the

following requirements are met:

Solely for device variants with the characteristic value CC for the

working voltage:

The power supply is Class 2 compliant.

The power supply conforms to overvoltage category I or II.

The working voltage inputs are designed for operation with safety

extra-low voltage. Connect only SELV circuits with voltage

restrictions in line with IEC/EN 60950-1 to the working voltage

connections.

The power supply has an easily accessible disconnecting device

(e.g., a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

The electrical wires are voltage-free.

A fuse suitable for DC voltage is located in the plus conductor of the

power supply.

The minus conductor is on ground potential. Otherwise, a fuse is

also located in the minus conductor.

Regarding the properties of this fuse: See “General technical data”

on page 49.

The wire diameter of the power supply cable is at least 1 mm²

(North America: AWG16) on the working voltage input.

The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

8Installation RSPE 30/32/35/37

Release

08/2014

The power supply cables used are permitted for the temperature

range required by the application case.

Relevant for North America:

The power cords are suitable for ambient air temperatures of at

least 167 °F (75 °C). The power cord wires are made of copper.

Start connecting the electrical wires only if all the above safety

requirements are fulfilled.

Internal fuses are triggered solely in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

working voltage and return the device to the plant for inspection.

For operating voltage connections with a protective conductor

connection: connect the protective conductor before connecting the

conductors for the operating voltage.

Only switch on the operating voltage for the device when the following

requirements are fulfilled:

The housing is closed

The terminal blocks are wired correctly

The terminal blocks for the operating supply are connected

Signal contact

For the signal contact to be connected, make sure the following

requirements are met:

The device is grounded.

The signal contact connection wires are voltage-free.

The connected voltage is limited by a current limitation device or a

fuse.

Observe the electrical threshold values for the signal contact.

See “General technical data” on page 49.

Start connecting the signal contact solely if all the above requirements are

fulfilled.

Installation site requirements

Install the device in a fire protected enclosure according to

EN 60950-1.

Only for device variants featuring working voltage with the

characteristic value K9 or KK:

See “Device name and product code” on page 13.

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

Installation RSPE 30/32/35/37

Release

08/2014 9

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

Install the device in the vertical position.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

The product can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55022

Reliability: EN 60950-1

You find more information on technical and industry standards here:

“Technical data” on page 49

Device variant Directive

All variants 2004/108/EC (EMC)

Directive of the European Parliament and the council for stan-

dardizing the regulations of member states with regard to elec-

tromagnetic compatibility.

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the

restriction of the use of certain hazardous substances in elec-

trical and electronic equipment.

Only for device variants featur-

ing working voltage with the

characteristic value K9 or KK:

2006/95/EC

Directive of the European Parliament and the council for stan-

dardizing the regulations of member states with regard to elec-

trical equipment to be used within specific voltage ranges.

10 Installation RSPE 30/32/35/37

Release

08/2014

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

LED or laser components

LED or LASER components according to IEC 60825-1 (2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Note: You will find additional warning and safety information in the “User

Manual Installation RSPE 30/32/35/37” supplied with every RSPE

30/32/35/37 device.

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belden Schalten Handbücher

Belden

Belden HIRSCHMANN EESX Series Kurzanleitung zur Einrichtung

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Bedienungsanleitung

Belden

Belden Hirschmann SPIDER 8TX EEC Handbuch

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden Telecast Fiber Systems THOR-SLG Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Belden

Belden grass valley MASTERPIECE 12G-SDI Bedienungsanleitung

Belden

Belden MAMMUTHUS MTM2800-PSU120 Bedienungsanleitung

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Bedienungsanleitung

Belden

Belden Hirschmann MACH102 Series Bedienungsanleitung

Belden

Belden Grass Valley Kayenne Beilage

Belden

Belden Hirschmann SPIDER-SL-20-08T1999999SY9HHHH Bedienungsanleitung

Belden

Belden HIRSCHMANN RSP20 Bedienungsanleitung

Belden

Belden grass valley SIRIUS 800 Series Benutzerhandbuch

Belden

Belden Hirschmann MACH104 Series Benutzerhandbuch

Belden

Belden Hirschmann MICE MS20 Bedienungsanleitung

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Bedienungsanleitung

Belden

Belden Thinklogical TLX48 Bedienungsanleitung

Belden

Belden HIRSCHMANN OCTOPUS OS24 Series Bedienungsanleitung

Belden

Belden ThinkLogical TLX12 Bedienungsanleitung

Belden

Belden Hirschmann MACH4002 Series Bedienungsanleitung

Belden

Belden HIRSCHMANN Octopus II Bedienungsanleitung

Belden

Belden grass valley KULA AV Bedienungsanleitung

Belden

Belden Hirschmann RS20 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung