Belkin BITRONICS P72655 Bedienungsanleitung

Bitronics Switch Kit

User Manual

P72655

READ THIS MANUAL IN ITS ENTIRETY BEFORE

ATTEMPTING TO CONNECT DEVICES, THE

BITRONICS SWITCH, OR INSTALLING THE

SOFTWARE. IMPROPER SETTINGS OR

CONFIGURATIONS CAN CAUSE DATA

CORRUPTION.

Page 2

I. Introduction

Thank you for purchasing the Belkin Components Bitronics DualBus Switch Kit! Now, you and your colleague can share and select

between two different parallel devices from your desktop. Plus, if you are using Windows 95 or 98, you will take advantage of Virtual

Port Software, which allows you to print automatically!

The Bitronics DualBus Switch gives you and another computer the ability to communicate to two parallel devices at the same time.

Also, it allows you to switch so that either user can use either device through the switching software.

II. Package Contents

•Bitronics DualBus Switch, 2-2 F1U127

•Power Adapter, 9VDC, 600mA F1D065-PWR

•2 x IEEE 1284 compliant cables F2A047-06

•User manual P72655

•Registration card P72009

III. Product Detail

Connectors to Devices

Connectors to Computers

Device LEDs

Computer LEDs

Manual select buttons

DIP Switch Settings (ON is Down)

SW1 – RESET switch ON: Normal Operation

OFF: RESET the switch

SW2 and SW3 – Time Out setting.

Time Out is the amount of time the switch remains locked on a

computer after data transfer. Use a longer Time Out when

connecting to Scanners, Mass Storage Devices, or when printing

large print jobs.

SW2 SW3 Time Out Setting

ON ON 5 seconds

ON OFF 10 seconds

OFF ON 20 seconds

OFF OFF 40 seconds

SW4 – Not used

!Recommended

Optional DIP Switches

Power Jack

9VDC, 500mA,

Center positive

Page 3

Printer Button Computer Button

IV. Choose your Operating System

•Windows3.x "Continue below:

•Windows95/98 and NT "Continue to next page.

•MS-DOS "Continue below:

V. Manual Mode

In manual mode, you can select port manually through the buttons on the Bitronics switch.

•Press computer to select which computer port you wish to configure. For the computer connected to Port 1, press the

COMPUTER button until the LEDs on Port 1 are lit up either in red or green.

•When you have selected which computer you wish to configure, now press the PRINTER button until the LED of the

appropriate device port you wish to use is lit up.

•For example, if you want computer 2 to use the device on port A,

press the COMPUTER button until the LEDs on “2” are lit up. Then,

press the PRINTER button until LED “A” is lit up.

•To use File Transfer mode, press the printer button until the LEDs

on the computer ports turn green. That means that that port is

ready for file transfer mode. For file transfer mode to be successful

for both PCs, the both computer ports must be set file transfer

mode – which is evident when the LEDs next to “1” and “2” are

green. For more information on File Transfer, please see page 12.

VI. Windows



3.x

In Windows3.x, you will have to exit to MS-DOS first to make this easier:

1. At the C:\> prompt, type the following and press ENTER:

md c:\Belkin

2. Insert the floppy disk containing the Windows3.x software (part# P72736) into your a: drive.

3. At the next prompt, type the following and press ENTER:

copy a:\Win3.x\F1U125e.exe c:\Belkin

4. When you get the prompt back, restart your computer and go back into Windows.

5. Lastly, you will have to create a shortcut to the program. In the Program Manager, select the Start Up window by

clicking on WINDOW, then START UP.

6. Click on FILE, NEW, PROGRAM ITEM, then OK. The next window must be filled out like this:

When done, click OK.

In Windows3.x, there is no possibility in making the software automatic because of the limitations of the operating system. Hence,

you will need to use this software each time you need to switch ports. Since it is in the START UP program group, each time you

start Windows, the program will be running.

Page 4

VII. MS-DOS

In MS-DOS, there re two files which can be used, and both are in the first disk (part# P72735) in the DOS subdirectory. These files

are: •DOSSWTCH.com

•F1U125.com

DOSSWTCH.com is a directly executable program. You must follow the syntax in order to invoke the switch to change ports. For

example, entering the following,

DOSSWTCH LPT1 A

will cause the switch to set your current computer to connect to Port A.

F1U125.com is a TSR program. Once it is loaded, it stays in memory. You can access it in any non-protected DOS-mode program by

pressing both SHIFT keys simultaneously. The following window will pop-up:

To make a selection, hit ENTER, and to go back, hit ESC. You can also change the “Hot Key” from the default L_SHIFT and R_SHIFT,

to something else you prefer.

Page 5

VIII. Windows



95 / 98 and NT

BEFORE YOU INSTALL THE BELKIN BITRONICS SOFTWARE, YOU MUST FIRST MAKE SURE THAT EACH DEVICE WORKS

PROPERLY ON ITS OWN WITH EACH COMPUTER

1. Make sure that the printer port on your computer is set to ECP mode. To do this, you must go into your computer’s BIOS or

CMOS setup. Instructions on how to do this differ from one computer to the next. Please consult your computer manufacturer’s

manual, tech support, or website for information on how to do this. Please do not call Belkin Tech Support on this

because each computer’s BIOS setup routine is different.

2. Make sure that the software and drivers for the devices to be shared are properly installed on both computers. If you are

sharing two printers between two computers, make sure that the printer drivers for both printers are installed and working

properly on both computers. If you are sharing a Zipdrive and a scanner between two computers, make sure that the

software and drivers of each device are installed and working properly on both computers.

3. Connect the two computers, and the device to be shared to the Bitronics Switch as shown below. The cables from the

computers to the Bitronics switch are included in the package. Take note of which port each device is connected to:

The example shown has a Zipdrive connected to Port A and an InkJet printer on Port B of the switch.

4. In order for both computers to properly share the devices, the software must be installed on both computers.

4.1. Put the disk into your floppy drive. Click on START, then RUN. Enter a:\BITRONIX.exe, then click OK

4.2. You will see the following window. Click SETUP.

Device A connected to

Port A

Device B connected to

Port B

These two cables

included

Page 6

4.3. Close all other running applications so that the software installation can proceed quickly and smoothly. Click NEXT.

4.4. Select the model of Bitronics Switch you have, which is the F1U127 / F1U128. Click NEXT.

Page 7

4.5. Select destination folder. The default folder is recommended. Click NEXT.

4.6. Select Program Folder. The default is the recommended. Click NEXT.

Page 8

4.7. When done installing, the program will ask you to restart your computer. You must restart in order to activate the

software properly. Click FINISH.

5. Once your computer has rebooted, the Bitronics icon will appear in your system tray.

6. Double-click on the icon to open up the setup program:

Select the correct LPT

port the Bitronics

switch is connected

to. If you only have

ONE parallel port

(usually that is the

case), leave this in

LPT1.

Page 9

7. Click on SETTINGS. Here, we have to tell the software what devices are connect to which port:

Click OK when done.

8. If one or both of the devices being shared is a printer, you must follow the procedure below to reconfigure the port connected to

the printer. If both devices are printers, then this must be done for both printers.

8.1. Click on START, SETTINGS, PRINTERS.

8.2. Right-click on the printer installed on the Bitronics switch, and click on PROPERTIES:

DISPLAY NAME is a free text field. You can

enter any description here for the attached

devices. For instance, Port A has the Zip

drive connected and Port B has the InkJet

connected. You can rename these fields to say

“My Zip Drive” and “Color Printer #2”.

DEVICE TYPE gives you a pull-down menu showing the types of

printers installed on your computer and other parallel devices as

well.

Here, you must select the correct type for the device

connected to that port.

•If you are using a device which adds a drive letter to

your system (like a ZipDrive, CD-ROM, LS-120, etc...), use

MASS STORAGE DEVICE.

•If you are using a printer, use the printer driver used

for that particular printer on that port of the Bitronics switch.

If it does not show up in this menu, that means the printer

drivers have not been installed. (If not, reinstall the printer

drivers and repeat this step after rebooting your computer.)

If you have more than one printer installed, make sure that

the correct driver is used for the printer connected to that

port on the Bitronics switch.

•For any other parallel device, just use SCANNER, and

change the DISPLAY NAME accordingly. For example, if you

have a parallel tape drive, use SCANNER for DEVICE TYPE,

then enter “Tape Drive” in DISPLAY NAME.

Page 10

8.3. Click on the DETAILS tab. In the pull-down menu “Print to the following port:”, select the correct port this printer

is connected to on the Bitronics switch:

•LPx1 – PA (auto switch) "Select this if the printer is connected to Port A of the Bitronics switch

•LPx1 – PB (auto switch) "Select this if the printer is connected to Port B of the Bitronics switch

In the image below, the printer is connected to Port B of the Bitronics switch. Therefore, LPx1 – PB (auto switch) is

selected. When done, click OK.

8.4. Click on SPOOL SETTINGS and click on “Start printing after last page is spooled”.

8.5. If NOT grayed out, click on “Disable bi-directional support for this printer”. Otherwise, ignore.

8.6. Click OK in the Spool Settings window, and OK again in the main properties window.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Belkin Schalten Handbücher

Belkin

Belkin OmniViewIP 5216K Bedienungsanleitung

Belkin

Belkin F1DH104L Bedienungsanleitung

Belkin

Belkin OMNIVIEW F1DA104PEA Bedienungsanleitung

Belkin

Belkin F1DE101H Bedienungsanleitung

Belkin

Belkin F5D5131-16 - 10/100 Switch Bedienungsanleitung

Belkin

Belkin F1DE101H Bedienungsanleitung

Belkin

Belkin F1DK102PEA Bedienungsanleitung

Belkin

Belkin HI-SPEED USB 2.0 EXTERNAL DRIVE ENCLOSURE Bedienungsanleitung

Belkin

Belkin OmniView F1DE108C Bedienungsanleitung

Belkin

Belkin P75341ej Bedienungsanleitung

Belkin

Belkin OmniView Secure F1DN104U Bedienungsanleitung

Belkin

Belkin OmniView F1DP108G Bedienungsanleitung

Belkin

Belkin OMNIVIEW F1DA104PEA Bedienungsanleitung

Belkin

Belkin F5U302 - Wireless USB Hub Bedienungsanleitung

Belkin

Belkin OmniView PRO F1D104-OSD Bedienungsanleitung

Belkin

Belkin F5U021 Installationsanleitung

Belkin

Belkin F5D5130-5 Bedienungsanleitung

Belkin

Belkin F1DN104B-3 Bedienungsanleitung

Belkin

Belkin Bitronics AutoSwitch Kit Bedienungsanleitung

Belkin

Belkin F1DJ102PeaB Bedienungsanleitung

Belkin

Belkin F1U400 - 4x4 USB Peripheral Switch Sharing Bedienungsanleitung

Belkin

Belkin P75470ea Bedienungsanleitung

Belkin

Belkin OMNIVIEW F1DA104PEA Bedienungsanleitung

Belkin

Belkin F1U117 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung