Berner GEDORE 1.06 Bedienungsanleitung

Bedienungsanleitung

Zweiarmabzieher-Satz

Artikelnummer:

895342

Sprachen:

en, fr, de, es

BERNER_Bedienungsanleitung_Zweiarmabzieher-Satz_76720[PDF]_de.pdf 2016-11-10

11/2011

Operating instructions

Instrucciones de Manejo

Instructions d‘Emploi

Betriebsanleitung

Pullers 1.06, 1.07, 1.08

Extractores 1.06, 1.07, 1.08

Extracteurs 1.06, 1.07, 1.08

Abzieher 1.06, 1.07, 1.08 02 - 17

18 - 34

35 - 51

52 - 68

www.gedore.com

AVOID INJURY. You MUST read and understand these

Operating Instructions before using the pullers.

EVITE LESIONES. Usted TIENE que leer y entender este manual,

antes de usar los extractores.

EVITER TOUTE BLESSURE. Vous DEVEZ lire et comprendre ce

mode d‘emploi avant d‘utiliser les extracteurs.

VERMEIDE VERLETZUNGEN. Sie MÜSSEN diese Betriebsanleitung

lesen und verstehen, bevor Sie die Abzieher benutzen.

Table of Contents

1. Important Safety Information 3

1.1 Safety Warnings 3

Overload Hazard 3

Electrical Shock Hazard 4

1.2 Personal Protective Equipment 4

1.3 Intended Use 5

1.4 Handling 5

1.5 Work Environment 5

2. Product Description 6

3. Preparing the Puller for Use 7

3.1 Assembling the Spindle 7

3.2 Assembling Pulling Legs on the Traverse 7

3.3 Clamping Pulling Legs on the Traverse 9

4. Safe Use 11

4.1 Settings for Pulling 12

4.2 The Pulling Process 13

5. Removing the Puller 15

6. Care and Storage 16

7. Optional Accessories 16

8. Maintenance and Repair 16

9. Environmentally Friendly Disposal 16

10. Technical Data 17

1. Important Safety Information

Read and understand these Operating Instructions before using the puller.

SERIOUS INJURIES or DEATH can result from incorrect use. These Operating

Instructions are part of the puller. They must be kept in a safe place for later use

and be passed along with the puller if it is sold, loaned, or otherwise transferred.

The puller should be used only by TRAINED PERSONNEL who have been

taught how to safely use and handle the puller. Using the puller without proper

training may result in SERIOUS INJURIES or DEATH. If you are unsure of

which puller or attachment to select, or the proper use of the selected puller,

contact GEDORE.

Employers purchasing this puller MUST ensure employees using the puller have

read and understood these Operating Instructions prior to using the puller.

The Operating Instructions MUST be available to the employees for reference

at all times.

1.1 Safety Warnings

Throughout this manual WARNING, CAUTION, NOTICE, and the SAFETY

ALERT SYMBOL will be used.

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

Addresses practices not related to personal injury. Relates

to property damage or damage to the puller.

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

OVERLOAD HAZARD

The puller can break during use and cause SERIOUS INJURY or DEATH.

NEVER use electric or pneumatic torque multipliers, impact wrenches or

impact drivers.

NEVER lengthen the drive tool for the puller.

NEVER hit the drive tool with a hammer.

ELECTRICAL SHOCK HAZARD

Contact with live electrical parts or circuits could result in SERIOUS

INJURY or DEATH.

ALWAYS DISCONNECT electricity before using puller on or

near electrical parts or circuits.

1.2 Personal Protective Equipment

ALWAYS wear personal protective equipment when using the puller. The

puller can slip or break causing SERIOUS INJURIES.

EYE PROTECTION (see ANSI Z87.1) designed to protect you from FLYING

OBJECTS must be worn when using the puller.

•Particles may fly upward during work with the puller and cause

SERIOUS INJURY to your eyes.

SAFETY GLOVES must be worn when using the puller.

•The puller can slip or break during use causing SERIOUS INJURY to

your fingers and hands.

SAFETY SHOES with slip-resistant soles and steel toe caps (see ASTM

F2413-05) must be worn when using the puller.

•Falling parts can cause SERIOUS INJURY to your feet and toes.

PROTECTIVE SAFETY COVERS should be utilized when using the puller (see

Section 7, Optional Accessories).

•For added safety, GEDORE highly recommends the use of a Protective

Safety Cover when using the puller.

•High forces exerted on the part being pulled can cause breakage and flying

debris, resulting in SERIOUS INJURIES.

•Safety covers provide maximum active-safety protection from suddenly

detaching ball bearings, driving pinions, or other small parts.

1.3 Intended Use

The puller is designed to remove pulleys, ball bearings, gear wheels, and other

components from shafts and axles.

•DO NOT use the puller for any other purpose.

•MISUSE can lead to SERIOUS INJURY or DEATH.

•DO NOT allow children to use the puller.

1.4 Handling

ELECTRICAL SHOCK HAZARD. ALWAYS DISCONNECT electricity before

using the puller on or near electrical parts or circuits.

Take the following safety precautions to prevent injuries and damage caused by

improper handling and unsafe use of the puller:

Improper handling can result in SERIOUS INJURY or DEATH.

•ALWAYS check the puller for damage before use.

•ALWAYS replace damaged or worn parts before use.

•ALWAYS use only GEDORE original spare parts and accessories.

•NEVER use electric or pneumatic torque multipliers or impact wrenches.

•NEVER use electric, pneumatic, or percussion drivers.

•NEVER heat the puller.

•NEVER modify any parts of the puller, especially the pulling legs.

•NEVER bend over the part being pulled during the pulling process.

•DO NOT allow children to use the puller.

1.5 Work Environment

ALWAYS use the puller in a safe work environment.

•Keep the work area clean and tidy.

•Use the puller in a large and secured area.

2. Product Description

Type 1.06 (2-arm) and

Type 1.07 (3-arm)

A: Traverse

B: Spindle

C: Pulling legs

D: Clamps

E: Screw

F: Drive hex

G: Spindle point

H: Nut

Type 1.08

with quick adjustment

A: Traverse

B: Spindle

C: Pulling legs

D: Clamps

E: Gripping lever

F: Drive hex

G: Spindle point

H: Knurled nut

I: Unlock-lever for

quick adjustment

Diagram depicts Type 1.06.

3. Preparing the Puller for Use

ALWAYS assemble the pullers on a work bench. During the assembly of the

puller, parts can fall off and cause INJURIES.

3.1 Assembling the Spindle

Type 1.06 and 1.07

Screw the spindle (B) into the

traverse (A).

Type 1.08

See Section 4.2 for spindle assembly instructions.

3.2 Assembling Pulling Legs on the Traverse

PINCH HAZARD. Take the following precautions to prevent pinch injuries to your

fingers when sliding the pulling legs on the traverse:

•ALWAYS perform the assembly on a work bench.

•DO NOT grasp in between the pulling legs when sliding the pulling legs on

the traverse with your fingers.

•Hold the traverse horizontally so that the pulling legs cannot slip down.

The pulling legs can subsequently slip back off the traverse and fall on feet or

legs causing INJURIES.

NOTE: There are different pulling legs with various clamping methods. Each

clamping method is explained in the following instructions. Follow the instructions

for the model you have purchased.

Type 1.06 and 1.07 -

Pulling legs with screw clamp

Loosen the screw connection (E, H)

until you can push the pulling legs

onto the traverse easily.

Push the pulling legs (C) onto

the traverse (A).

Type 1.06/E, 1.07/E, 1.08

Pulling legs with gripping lever

Open the gripping lever (E) on the

pulling leg (C) to loosen the clamp (D).

Push the pulling legs (C) onto

the traverse (A).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Berner Werkzeuge Handbücher

Berner

Berner 419455 Bedienungsanleitung

Berner

Berner 407716 Bedienungsanleitung

Berner

Berner BPT-IW 1/2 PREMIUM HYBRID Bedienungsanleitung

Berner

Berner CoPrA 102012208176 Bedienungsanleitung

Berner

Berner Tornador BPT-TG B011 Bedienungsanleitung

Berner

Berner BACGG Bedienungsanleitung

Berner

Berner BPT-IW-3/4 HYBRID Bedienungsanleitung

Berner

Berner BPT-IW 1/2 PREMIUM HYBRID STUBBY Bedienungsanleitung

Berner

Berner 1000352 Bedienungsanleitung

Berner

Berner BPT-IW-1/2 HYBRID Bedienungsanleitung

Berner

Berner Mato Lube Shuttle BACGG Bedienungsanleitung

Berner

Berner S.F.2C Bedienungsanleitung

Berner

Berner BPT-RA 1/4 Bedienungsanleitung

Berner

Berner WINSHIELD REMOVER MONO Bedienungsanleitung

Berner

Berner 156014 Bedienungsanleitung

Berner

Berner 365906 Bedienungsanleitung

Berner

Berner BACAGXB 18V Bedienungsanleitung

Berner

Berner DL 5070 Bedienungsanleitung

Berner

Berner MATO BACGG Bedienungsanleitung

Berner

Berner BPT-IW 3/4 PREMIUM HYBRID SHORT Bedienungsanleitung

Berner

Berner 414705 Bedienungsanleitung

Berner

Berner BPT-IW 1 PREMIUM PISTOL Bedienungsanleitung

Berner

Berner 188013 Bedienungsanleitung

Berner

Berner X-Lux Wireless Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung