Besam PowerSwing Bedienungsanleitung

Andere Handbücher für PowerSwing

1

Inhaltsverzeichnis

Andere Besam Türöffnungssystem Handbücher

Besam

Besam SW200i Bedienungsanleitung

Besam

Besam SW 100 Handbuch

Besam

Besam AAE977 Bedienungsanleitung

Besam

Besam ASSA ABLOY Swingmaster 900 Bedienungsanleitung

Besam

Besam PowerSwing Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

Besam

Besam OPB Bedienungsanleitung

Besam

Besam SW200i Handbuch

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung

AAE320

The New Besam Swing door operator

PowerSwing

Standard cover Special cover

Door leaf-mounted Double door operators

Main models of the PowerSwing operator

• The operator works electro-hydraulically.

• Closing power from a coil spring

• The open position is kept by a hydraulic valve.

• ”Lock kick” to overcome the resistance of a striking plate

• Dimension standard cover LxHxD 716x110x110 mm

1. Mounting plate

2. Motor/ Pump

3. Valve

4. Hydraulic unit

5. Drive shaft

10. Extension unit, EXA (option)

11. End plate

12. Programme selector, PS-3 (option)

13. Cover

14. Bearing sleeve

15. Cable holder

16. Lid

Identification PowerSwing

6. Spring tube

7. Cable inlet

8. Mains connection

9. Control unit, CSDA

Arm systems

PUSH Arm system PULL Arm system

Wall mounted operator, arm system PUSH

• Decide X

• Draw a line on the wall for the underside of the mounting plate

• Door adaptor should

not be mounted on

glass bead

• Extension has to be

used if operator must

be mounted higher up

on the wall

* Min. 31 mm to

enable drive arm to

pass underneath

Note!

Wall mounted operator, arm system PUSH

• Cut out the appropriate template from the card board box

• Ensure that the template aligns with the drawn line (X) and the L1.

• Use the stickers in the mounting kit to fix the template to the wall

• Punch where to drill

C

Wall mounted operator, arm system PUSH

1. Drill the four mounting holes and the two holes for the door fitting.

2. Remove the template.

3. Tap, plug, or reinforce with rivnuts and screw the drive unit tight.

Mounting the PUSH drive arm

1. Adaptor

2. Drive arm

1. Remove the door fitting from the arm system.

2. Screw the door fitting to the door leaf tight.

3. Mount the drive arm and adaptor on the operator drive shaft at an

angle of 90° to the wall.

4. Ensure that the teeth of the adaptor engage fully with the operator

shaft. Tighten the screw to a torque of 25 Nm. (19 lbf.ft)