Beta 1760 PA/AC Bedienungsanleitung
ENFRAIT
AMPEROMETRIC CLAMP
MOD. 1760 PA/AC
PINZAAMPEROMETRICA
MOD. 1760 PA/AC
PINCE AMPEREMETRIQUE
MOD. 1760 PA/AC
ZANGENSTROMMESSER
MOD. 1760 PA/AC
PINZAAMPERIMÉTRICA
MOD. 1760 PA/AC
ESDE
EN
2
AMPEROMETRIC CLAMP
MOD. 1760 PA/AC
SAFETY NOTES
Do not exceed the maximum allowable input range of any function
Do not apply voltage to meter when resistance function is selected.
Set the function switch OFF when the meter is not in use.
WARNINGS
Set function switch to the appropriate position before measuring.
When measuring volts do not switch to current/resistance modes.
Do not measure current on a circuit whose voltage exceeds 240V.
•
•
•
•
•
•
This symbol, adjacent to another symbol or terminal, indicates the user must refer to this
manual for further information.
This symbol, adjacent to a terminal indicates that under normal use hazardous voltages
may be present
Double insulation
EN
3
CAUTIONS
Improper use of this meter can cause damage, shock, injury or death. Read and understand this
user manual before operating the meter.
Always remove the test leads before replacing the battery.
Inspect the condition of the test leads and the meter itself for any damage before operating
the meter. Repair or replace any damage before use.
Use great care when making measurements if the voltages are greater than 25 V AC rms or
35 V DC. These voltages are considered a shock hazard.
Remove the battery if the meter is to be stored for long periods.
Always discharge capacitors and remove power from the device under test before
performing Diode, Resistance or Continuity tests.
Voltage checks on electrical outlets can be difcult and misleading because of the uncertainty
of connection to the recessed electrical contacts. Other means should be used to ensure that the
terminals are not “live”.
If the equipment is used in a manner not specied by the manufacturer, the protection provided
by the equipment may be impaired.
•
•
When changing ranges using the selector switch always disconnect the test leads from the circuit
under test.
Do not exceed the maximum rated input limits.
•
•
EN
4
Inputs limits
Function Maximum input
A AC 1000 A
V DC, V AC 600 V DC/AC
Resistance, diode, continuity, Capacitance,
Frequency, Duty cycle, test 250 V DC/AC
Temperature 60 V DC/24 V AC
EN
5
1. Current clamp
2. Clamp trigger
3. Data hold and backlight
button
4. Mode select button
5. LCD display
6. COM input jack
7. Rotary function switch
8. Range select button
9. Hz/% duty button
10. V- - °C/F jack
11. Battery cover
AC (alternating current) and DC (direct currrent)
Minus sign
4 digits (0 to 3999) measurement reading
Auto Range mode
Diode test mode
Audible Continuity
Data Hold mode
°C, °F, µm,V, A,K, M, - units of measure list
1
2
3
4
5
6
7
8
METER DESCRIPTION
1
2
3
4 5 6 7 8
EN
6
Functions Range and resolution Accuracy (% of reading)
40.00 AAC ± (2,5% +10 digits)
AC Current 400.0 AAC ± (2,5% +5 digits)
1000 AAC ± (3.0% +4 digits)
400.0 mV DC ± (0.8% +3 digits)
4.000 V DC
DC Voltage 40.00 V DC ± (1.5% +3 digits)
400.0 V DC
600 V DC ± (2.0% +3 digits)
400.0 mV AC ± (0.8% +20 digits)
4.000 V AC
AC Voltage 40.00 V AC ± (1.8% +5 digits)
400.0 V AC
600.0 V AC ± (2.5% +5 digits)
400.0 ± (1.0% +4 digits)
4.000 K
Resistence 40.00 K ± (1.5% +2 digits)
400.0 K
4.000 M ± (2,5% +3 digits)
40.00 M ± (3,5% +5 digits)
SPECIFICATIONS
EN
7
40.00 nF ± (5.0% reading +100 digits)
400.0 nF ± (3.0% reading +5 digits)
Capacitance 4.000 µF ± (3.5% reading +5 digits)
40.00 µF
100.0 µF ± (5.0% +5 digits)
5.000 Hz ± (1,5% +5 digits)
50.00 Hz
500.0 Hz ± (1,2% +2 digits)
Frequency 5.000 KHz Sensivity: 10mV rms min
50.00 KHz
500.0 KHz
5 MHz ± (1.5% reading +10 digits)
10.00 MHz
Duty Cycle 0.5 a 99.0% ± (1.2% reading + 2 digits)
Pulse width: 100us – 100ms
Temperature -50.0 to 400.0°C ± (3.0% reading +5°C)
(Type K probe) 400 to 1000°C
(probe accuracy -58.0 a 400.0°F ± (3.0% reading +7°F)
not included) 400 to 1832 °F
Note: no autoranging and 400mV AC Voltage range
EN
8
Clamp size Opening 1.2” (30mm) approx
Diode Test Test current of 0.3 mA typical - Open circuit voltage 1.5V DC typical
Continuity Check Threshold <1000; Test current < 1mA
Low Battery Indication “ “ is displayed
Overrange Indication “OL” is displayed
Measurements Rate 2 per second, nominal
Input Impedance 7.8 Mohm (VDC and VAC)
Display LCD 4 digits backlighted
AC Current 50/60Hz (AAC)
AC Voltage bandwidth 50/60HZ (VAC)
Operating Temperature 14 to 122°F (-10 to 50°C))
Storage Temperature -14 to 140°F (-30 to 60°C))
Relative Humidity 90% (0°C to 30°C); 75% (30°C to 40°C); 45% (40°C to 50°C)
Altitude Operating: 3000 m; Storage 10.000 m
Over voltage Category III 600 V
Battery One “9V” battery
Auto OFF Approx. 30 minutes
Dimensions/Weight 229 x 80 x 49 mm / 303 g
Safety For indoor use and in accordance with Overvoltage Category II,
Pollution Degree 2 - Category II includes local level, appliance,
portable equipment, etc., with transient overvoltages less than
Overvoltage Cat. Ill
EN
9
OPERATION
Notices: Read and understand all warning and precaution statements listed in the safety
section of this operation manual prior to using this meter. Set the function select switch to
the OFF position when the meter is not in use.
AC Current Measurements
Warning: Ensure that the test leads are disconnected from the meter before making current
clamp measurements.
Set the Function switch to the 1000A or 400A ‘or 40A range. If the range of the measured is
not known, select the higher range rst then move to the lower range if necessary.
Press the trigger to open jaw. Fully enclose one conductor to be measured
The clamp meter LCD will display the reading
DC/AC Voltage Measurements
Insert the black test lead into the negative COM terminal
and the red test lead into the positive V terminal.
Set the function switch to the V position.
Select AC or DC with the MODE button
Connect the test leads in parallel to the circuit under test.
Read the voltage measurement on the LCD display.
1
2
3
1
2
3
4
5
NO YES
EN
10
Resistance and Continuity Measurements
Insert the black test lead into the negative COM terminal and the red test lead into the
positive terminal.
Set the function switch to the position.
Use the multifunction MODE button to select resistance.
Touch the test probe tips across the circuit or component under test. It is best to disconnect
one side of the device under test so the rest of the circuit will not interferewith the resistance
reading.
For Resistance tests, read the resistance on the LCD display.
For Continuity tests, if the resistance is < 100 , a tone will sound.
Diode Measurements
Insert the black test lead banana plug into the negative COM jack and the red test lead banana
plug into the positive diode jack.
Turn the rotary switch to the position.
Press the MODE button until appears in the display.
Touch the test probes to the diode under test. Forward voltage will indicate 0.4V to 0.7V.
Reverse voltage will indicate “OL”. Shorted devices will indicate near OmV and an open
device will indicate “OL” in both polarities.
1
2
3
4
5
6
1
2
3
4
Red probe Red probe
Black
probe
Black
probe
Inhaltsverzeichnis
Sprachen:
Andere Beta Messgerät Handbücher
Beta
Beta 1658DGT25 Bedienungsanleitung
Beta
Beta 1759M Bedienungsanleitung
Beta
Beta 1693L Bedienungsanleitung
Beta
Beta 15-H05 Bedienungsanleitung
Beta
Beta 1654DGT Bedienungsanleitung
Beta
Beta 1760PA/AC-DC Bedienungsanleitung
Beta
Beta 1760WM Beilage
Beta
Beta 1651DGT Bedienungsanleitung
Beta
Beta 1760PA/80 Bedienungsanleitung
Beta
Beta 588 Bedienungsanleitung
Beta
Beta 961 P6 Bedienungsanleitung
Beta
Beta 1843 15-H05 Bedienungsanleitung
Beta
Beta 961D Bedienungsanleitung
Beta
Beta D3000 Bedienungsanleitung
Beta
Beta 1662DGT Bedienungsanleitung
Beta
Beta 971 TSP Bedienungsanleitung
Beta
Beta 601C Bedienungsanleitung
Beta
Beta 1760/TC2 Bedienungsanleitung
Beta
Beta 1651DGT/IP Bedienungsanleitung
Beta
Beta 1899A Bedienungsanleitung
