Billy Goat AET60 Bedienungsanleitung

Part No. 100384

AET60 Owner’s Manual

Original Instructions

IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE

AERATOR 60” Owner's Manual

AET60

Beginning Serial #: 022417472

NOT FOR REPRODUCTION

Part No. 100384

Table of Contents

Specications, Intended Use, Replacement Parts & Safety

Instruction Labels, Packing Checklist, & Assembly

Operation

Maintenance and Troubleshooting

Illustrated Parts and Part Lists

Tine Replacement Kit Information

5-6

7-8

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

Specications

Total Unit Weight 443lb (201kg)

Width 37”-48”-60”

Maximum Operating Slope 15 °

Intended Use

Replacement Parts

Table 1: Specications

Your Billy Goat®Aerator

This machine is designed for aerating established lawns and large grass covered areas.

The machine should not be used for any other purpose than that stated above.

DO NOT OPERATE IF EXCESSIVE VIBRATION OCCURS!

If excessive vibration occurs, stop use of the unit immediately and check for damaged

or worn reel, loose hardware, or lodged debris.

Handling and Transporting

Always use four or more people to lift this machine. Lift holding on either side of the

machine, using the handles and the frame. Secure in place during transportation. See

specications for unit weight.

For safety use gloves when lifting.

P/N 360100

Replacement tip for

aerating tines.

TINE REPLACEMENT

Safety

PROPOSITION 65 STATEMENT

WARNING

This product can expose you to chemicals including gasoline engine exhaust, which is known to the State of

California to cause cancer, and carbon monoxide, which is known to the State of California to cause birth de-

fects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

Instruction Labels

The labels shown below were installed on your Billy Goat® Aerator. If any labels are

damaged or missing, replace them before operating this equipment. Part numbers from the

Illustrated Parts List are provided for convenience in ordering replacement labels. The correct

position for each label may be determined by referring to the part numbers shown.

LABEL DANGER CLEAR

P/N 100311

LABEL MAX LOAD

P/N 100356

LABEL HARD SOIL

P/N 100372

LABEL HITCH MOUNT

P/N 100374

Packing Checklist

Your Billy Goat® AET60 is shipped from the factory in one carton, completely assembled.

Read all safety instructions before assembling unit.

Take caution when removing the unit from the box.

Boxing Parts Checklist

Owner’s Manual

P/N 100384

Assembly

1. The machine is fully assembled; you will need to attach to a vehicle in the desired conguration (see

operation section for details).

Parts Bag and Literature Assembly

• Warranty Card P/N - 400972

• Owner’s Manual P/N - 100384

• General Safety and Warranty

Renovation Manual P/N - 100295

• General Safety and Warranty

Manual P/N - 100295

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

Operation

Item numbers in parentheses can be referenced in the Parts Illustration and Parts List on pages 7-9.

Operating Instructions

The AET60 is a combination of a tow-behind aerator and a 3-point aerator with two wings for

adjustable aeration widths. When used behind a tractor in the 3-point application, there are pins on

each tine assembly that can be removed to allow tines to swivel, enabling the tractor to turn while still

aerating with the tines in the ground. When being towed, the tine assemblies must be locked in place

for proper tracking.

Aerating Operation

NEVER PARK THIS UNIT ON A SLOPE OF ANY KIND. Always keep tines in the up position when

parking the unit.

Using as a Tow-Behind

When using this machine as a towable aerator, the tow link should be in the down position and

attached to the frame of the aerator using the two clevis pins (item 19). The tow behind is telescoping

so that it can be extended to accommodate various vehicles. Make sure all ve lock pins (item 21) are

in place on the axle assembly to prevent the assembly from swiveling. When operating, the wings can

either be up or down depending on the width of aeration desired. In normal conditions, there will be

adequate weight for proper penetration when the wings are up; when the wings are down, additional

weight may be required.

Using in a 3-Point Application

When used with a tractor and a 3-point hook up, the inner and outer tow link should slide together and

be in the upright position holding it to the frame with the two clevis pins (item 19). The two table on the

outer tow link are for the center link on the 3-point. Remove the ve lock pins (item 21) from the tine

axle to allow the assembly to swivel.

Raising and Lowering Tines

The tines are raised or lowered into the ground by operating the crank on the cylinder to raise or lower

the tines to the desired depth. Tine penetration is very dependent on surface preparation. READ the

entire operation section before aerating.

•Set Tine Depth: With the aerator in the work area, lower the tines into the ground by rotating the

crank at the rear.

•Transport: Be sure to raise tines out of the ground before transporting away from the work area.

Caster Raising/Lowering

The caster can be raised or lowered by removing the pin and rotating the caster then reinserting the

pin to lock it into position. DO NOT transport with the caster in the down position so that it comes into

contact with the ground. DO NOT unhitch the unit on uneven terrain with the caster down as the unit

may roll. To prevent unwanted roll, chock the wheels.

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

Operation Continued

Tips

• Mow - Mow the lawn to its normal cut height.

• Water - For the best performance and maximum tine penetration the lawn should be thoroughly watered

the day before aeration.

• Inspect - Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can

present a hazard during work prior to starting

• Identify - Mark all xed objects to be avoided during work, such as sprinkler heads, water valves, buried

cables, or clothes line anchors, etc.

• Slopes - Do not operate the aerator on steep slopes (any slope exceeding 15°). Use extreme caution

when operating on any sloped surface. For lesser sloped areas operate the unit, traversing up and down at

a 45° angle to the slope rather than straight across. Extended operation on steep slopes can cause engine

damage.

Maintenance

Item numbers in parentheses can be referenced in the Parts Illustration and Parts List on pages 7-9.

Periodic Maintenance

Periodic maintenance should be performed at the following intervals:

Maintenance Operation* Every Use (or daily) Every 10 hrs Every 50 hrs

Inspect for loose, worn, or

damaged parts •

Thoroughly clean all debris

from unit and tines •

Grease wheel bearings and

tine hubs •

Table 2: Maintenance

Troubleshooting

Problem Possible Cause Solution

Abnormal Vibration Damaged or missing tines. Loose

bolts.

Stop work immediately. Replace any

damaged or missing tines. Tighten all

loose nuts and bolts.

Table 3: Troubleshooting

*Engine must be level when checking or lling oil

Individual Tine Replacement

1. Remove the bolt and nut (Items 46 and 43, respectively).

2. Replace the tine and then secure it in place with hardware previously removed.

Note: Tines are a normal wear item and should be inspected regularly for signs of wear or damage.

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

AET60 Parts Drawing

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

AET60 Parts List

Item No. Part No. Description Quantity

1 381556 BASE FRAME WELDMENT 1

2 381557 LEFT WING FRAME WELDMENT 1

3 381558 RIGHT WING FRAME WELDMENT 5

4 380237 TINE ARM WA AET60 GEN 2 5

5 381560 WHEEL ASSEMBLY 1

6 381561 JACK ASSEMBLY 1

7 381562 OUTER TOW LINK 1

8 381563 INNER TOW LINK 1

9 380234 HUB, EIGHT TINE 10

10 440153 WASHER 1.5 OD X 0.453 ID X 0.25 THK 10

11 381566 ARM SWIVEL STOP 5

12 381567 WING HANDLE 2

13 381568 BASE LOAD PAN 1

14 381569 WING LOAD PAN 2

15 373280 BEARING, 6205 25mm BORE ARMORED SEALS 20

16 8181011 WSHR-STL, BLV, 0.402 X 0.877 X 0.63 CN MZ 10

17 8041050 SCREWCAP 3/8”-16 X 1” HCS ZP 10

18 381573 TINE ARM SHOULDER BUSHING 10

19 381574 CLEVIS PIN 7/16” X 3.5” 2

20 500267 GRIP HANDLE 1” X 5.5” 2

21 381576 LOCK PIN 3/8” X 2.5” 6

22 381577 CLEVIS PIN 3/4” X 3.5” 1

23 381578 CLEVIS PIN 7/8” X 3” 2

24 381579 CLEVIS PIN 5/8” X 1.75” 2

25 8041175 SCREWCAP 3/4”-10 X 5 1/2” HCS ZP 2

26 381581 NUT JAM 3/4”-10 2

27 381582 CLEVIS PIN 5/8” X 5” 1

28 381583 CLEVIS PIN 5/8” X 3.5” 1

29 281584 COTTER HAIR PIN 1/8" FOR 3/4 TO 7/8" 3

30 281585 HITCH PIN 5/8” X 4” W/LYNCH PIN 3

31 381586 COTTER HAIR PIN 1/8” FOR 7/16 TO 5/8 8

32 381587 CLEVIS PIN 7/16” X 2.5” 2

33 360100 TINE CORING 3/4” 80

34 381589 CLEVIS PIN 5/8” X 4” 4

35 381590 RUBBER BUMPER 1.5” X .75” THK 4

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

AET60 Parts List Continued

Item No. Part No. Description Quantity

36 381591 RUBBER BUMPER 1.0” X 1.0” THK 8

37 80150057 SHCS 10-32 X 1/2” 14

38 8171008 WASHER 3/4” SAE 8

39 381158 SHCS 10-32 X 1.25” 8

40 381595 RUBBER BUMPER 1.5” X 1.5” THK 2

41 381596 SHCS 1/4”-20 X 1.5” 2

42 381597 SHCS 1/4”-20 X .75” 4

43 8165003 NUT-HEX-NYLK, FLG 0.375” - 16 ZP 85

44 8041058 SCREWCAP 3/8”-16 X 3” HCS ZP 5

45 381440 WHEEL 13” 2

46 8041052 SCREWCAP 3/8”-16 X 1 1/2” HCS-ZP 80

47 8160002 NUTLOCK 5/16”-18 4

49 816003 NUTLOCK 3/8”-16 HEX ZP 5

50 8041010 SCREWCAP 1/4”-20 X 2” HCS ZP 2

51 8160001 NUTLOCK 1/4”-20 HEX ZP 4

52 8197031 COTTER PIN 1/8” X 1” 4

53 8172020 WASHER FENDER 5/16” 8

54 380134 TRANSPORT WHEEL STAND 1

55 610101 CASTER 5” DIA X 2” 1

56 8171003 WASHER 5/16” FLAT 8

57 8041028 SCREWCAP 5/16”-18 X 1” GR 5 HCS ZP 4

58 8041057 SCREWCAP 3/18”-16 X 2 3/4” ZP 5

59 380235 AXLE TINE ARM GEN 2 5

60 380236 SPACER, SPINDLE BEARING AET60 10

NOT FOR REPRODUCTION

100384_A_LO

Part No. 100384

Item No. Part No. Description Quantity

4 380237 TINE ARM WA AET60 GEN 2 1

9 380234 HUB, EIGHT TINE 2

10 440153 WASHER 1.5 OD X 0.453 ID X 0.25 THK 2

11 381566 ARM SWIVEL STOP 1

15 373280 BEARING, 6205 25mm BORE ARMORED SEALS 4

16 8181011 WSHR-STL, BLV, 0.402 X 0.877 X 0.63 CN MZ 2

17 8041050 SCREWCAP 3/8”-16 X 1” HCS ZP 2

21 381576 LOCK PIN 3/8” X 2.5” 1

33 360100 TINE CORING 3/4” 16

43 8165003 NUT-HEX-NYLK, FLG 0.375” - 16 ZP 16

44 8041058 SCREWCAP 3/8”-16 X 3” HCS ZP 1

46 8041052 SCREWCAP 3/8”-16 X 1 1/2” HCS-ZP 16

49 8160003 NUTLOCK 3/8”-16 HEX ZP 1

58 8041057 SCREWCAP 3/18”-16 X 2 3/4” ZP 1

59 380235 AXLE TINE ARM GEN 2 1

Tine Replacement Kit Information

The new Billy Goat® AET60 is built with newly designed tines. Owners of previous Billy Goat AET60 models

can purchase new tines in the form of a service kit (Part No. 380238). New owners can replace old or worn

tines with the same service kit.

To order a service kit, please visit www.billygoat.com or contact Billy Goat customer service at (816) 524-9666.

Your Billy Goat® Tine Replacement Kit will include the necessary instructions/literature

and the following parts:

NOT FOR REPRODUCTION

100384_A_LO

Inhaltsverzeichnis

Andere Billy Goat Rasen- und Gartengeräte Handbücher

Billy Goat

Billy Goat KD505SPQ Montageanleitung

Billy Goat

Billy Goat SC180HEU Bedienungsanleitung

Billy Goat

Billy Goat GZ401H Bedienungsanleitung

Billy Goat

Billy Goat 440140 Bedienungsanleitung

Billy Goat

Billy Goat LB351 Bedienungsanleitung

Billy Goat

Billy Goat TR1204L Bedienungsanleitung

Billy Goat

Billy Goat BG1002 Montageanleitung

Billy Goat

Billy Goat KD502SPQ Montageanleitung

Billy Goat

Billy Goat QV550HSP Bedienungsanleitung

Billy Goat

Billy Goat MV650SPHEU Bedienungsanleitung

Billy Goat

Billy Goat CR550HC Bedienungsanleitung

Billy Goat

Billy Goat OS900SPS Bedienungsanleitung

Billy Goat

Billy Goat CR550HC Montageanleitung

Billy Goat

Billy Goat PL25SPH Bedienungsanleitung

Billy Goat

Billy Goat HTR1602V Montageanleitung

Billy Goat

Billy Goat OS901SPS Bedienungsanleitung

Billy Goat

Billy Goat SC181H Bedienungsanleitung

Billy Goat

Billy Goat MV600SPE Bedienungsanleitung

Billy Goat

Billy Goat PL2500SPH Bedienungsanleitung

Billy Goat

Billy Goat PR550 Montageanleitung

Billy Goat

Billy Goat KV600SP Bedienungsanleitung

Billy Goat

Billy Goat QL2000VE Montageanleitung

Billy Goat

Billy Goat OS900SPS Bedienungsanleitung

Billy Goat

Billy Goat PL1802V Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung