Billy Goat PL1802V Bedienungsanleitung

382514_B_HI

PL1802V Owner’s Manual

Original Instructions

IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE

PL1802V Owner's Manual

NOT FOR REPRODUCTION

382514_B_HI

Table of Contents

Specications

Intended Use

Labels

Throttle Controls

Packing Checklist

Initial Set-Up Assembly

Operation

Maintenance

Troubleshooting

Spare Parts List

Warranty Information

Part Illustrations and Lists

6-7

7-17

20-33

NOT FOR REPRODUCTION

382514_B_HI

Specications

Engine: B&S VANGUARD 6.5HP w/6:1

Engine Model No. 12V3520006F1

Engine Fuel Capacity 3.7 qt. (3.1 L)

Engine Oil Capacity 0.63 qt. (0.59 L)

Total Unit Weight 242 lb (109.8 kg)

Length 57” (1.45 m)

Width 24”( .61 m)

Height 40” (1 m)

Maximum Operating Slope 15o

Intended Use

PL1802V

AERATOR

This machine is designed for aerating established lawns and large grass covered areas. The machine should

not be used for any other purpose than that stated above.

DO NOT OPERATE IF EXCESSIVE VIBRATION OCCURS!

If excessive vibration occurs, shut engine off immediately and check for damaged or worn reel, loose reel

bearing, loose engine or lodged debris. To remove debris from the machine, see the machine specic trouble

shooting section. Note: See parts list for proper bolt torque specications.

HANDLING & TRANSPORTING

Always use two or more people to lift these machines. Lift holding on either side of the machine, using the han-

dles and the frame. Secure in place during transportation. See specications for unit weight.

For safety, use gloves when lifting.

Never lift any machine while the engine is running.

NOT FOR REPRODUCTION

382514_B_HI

Warning Labels

The labels shown below were installed on your BILLY GOAT® Aerator. If any labels are damaged or

missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part

numbers are provided for convenience in ordering replacement labels. The correct position for each label may

be determined by referring to the Figure and Item numbers shown.

Fig. 1

DANGER KEEP HANDS

AND FEET AWAY

P/N 440424

DANGER

PINCH

POINT

100355

Fig. 2

LABEL PINCH POINT PLP/N

100355

Fig. 3

DECAL, WARNING, HAND IN BELT,

ENG. ONLY P/N 5103184

CHECK OIL BEFORE EACH USE.

GREASE ALL FITTINGS EVERY 10 HOURS OF OPERATION.

WE RECOMMEND ALMAGARD #3752 GREASE FROM

LUBRICATION ENGINEERS INC.

TO AERATE

1. Retract Tines With Center Control Lever.

2. Begin Forward Motion of Aerator Manually.

3. Engage Drive Lever With Aerator Already in Motion.

100354

Fig. 4

LABEL AERATING INST PL

Instruction Labels

PULL TO ENGAGE TINES

JALE HACIA ARRIBA PARA ENGRANAR LOS DIENTES

100356

Fig. 5

LABEL TINE ENGAGE PL

FORWARD TO LOWER TINES

BACK TO RAISE TINES

AVANCE PARA BAJAR LOS DIENTES

100357

Fig. 6

LABEL LOWER TINES PL

NOT FOR REPRODUCTION

382514_B_HI

Throttle Controls- Vanguard

RUNCHOKE

STOP

Set lever to choke when starting cold.

Set lever to dictate engine speed. To stop

the engine, move the lever completely to

the left.

Packing Checklist

Your Billy Goat aerator is shipped from the factory in one carton, completely assembled with the cables de-

tached.

READ all safety instructions before assembling unit.

TAKE CAUTION when removing the unit from its box or crate.

PUT OIL IN ENGINE BEFORE STARTING.

Boxing Parts Checklist

Operator’s Manual (382514)

Engine Manual (Briggs and

Stratton)

Figure A

NOT FOR REPRODUCTION

382514_B_HI

Operation

Initial Set-Up Assembly

Refer to Figure X in the Packing Checklist section to identify parts in Initial Set-Up Assembly.

1. UNFOLD the upper handle (A, Figure A) and slide handle lock loops (B, Figure A) into place to secure the

upper handle to the lower.

2. ATTACH the tine lift cable (C, Figure A) to the tine lever (D, Figure A) in the center of the handle by inserting

the pin into it. Then attach the bail cable (E, Figure A) to the bail (F, Figure A). Check to make sure the cables

are functioning properly before operation and not binding.

3. CHECK engine oil level and ll to proper level. Also check oil in gear reduction reservoir and ll if necessary.

See engine owner’s manual for type and amount of oil to use.

4. CONNECT spark plug wire. Set the engine stop switch (G, Figure A) to the ON position.

STARTING THE ENGINE

See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine must be level

when checking and lling oil and gasoline.

ENGINE SPEED: Controlled by lever on the engine. Under normal conditions, operate at the minimum

throttle speed to accomplish your task.

ON/OFF: Set the on/off switch to ON

FUEL VALVE: Move fuel valve to “ON” position.

CHOKE: Engage the choke when starting a cold engine.

THROTTLE: Move the throttle control lever on the engine to fast position. Pull starting rope to start engine.

If your unit fails to start, check trouble shooting section in operator’s manual and also see engine

manual.

AERATING OPERATION

Note: Never park this unit on a slope of any kind. Always keep tines in the up position when parking the unit.

TINES RAISING/LOWERING: The tines are raised or lowered into the ground by operating the tine en-

gagement lever on the upper handle. Tine penetration is very dependent on surface preparation. READ the

entire operation section before aerating.

ENGAGE TINES: With the aerator in the work area, lower the tines by releasing the center lever on the

handle. When the lever is in the forward position, pull up on the bail to engage the tines.

AERATE: Push the machine with the tines engaged. NOTE: In cold temperatures engage the tines in the

up position for two minutes to warm the cam grease. For maximum tine penetration apply downward pres-

sure on the handle.

NOT FOR REPRODUCTION

382514_B_HI

Operation

TURNING: At the end of an aerating run, release the bail and raise the tines out of the ground. Then repo-

sition the unit for another pass and lower the tines to begin another run.

TRANSPORT: Be sure to raise tines out of the ground (disengaging the bail and then raising the tines with

the center lever) before transporting away from the work area.

TIPS

MOW: Mow the lawn to its normal cut height.

WATER: For the best performance and maximum tine penetration the lawn should be thoroughly watered

the day before aeration.

INSPECT: Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can

present a hazard during work prior to starting.

IDENTIFY: Mark all xed objects to be avoided during work, such as sprinkler heads, water valves, buried

cables, or clothes line anchors, etc.

SLOPES: Do not operate the aerator on steep slopes (exceeding 15o). Use extreme caution when operat-

ing on any sloped surface. For lesser sloped areas operate the unit, traversing up and down at a 45o angle

to the slope rather than straight across. Extended operation on steep slopes can cause engine damage.

Maintenance

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation Every

Use

Every 10

Hrs

Every 50

Hrs

Every 100

Hrs

Inspect for loose, worn or damaged parts •

Check engine oil* •

Clean debris from unit and tines •

Grease cam bearings •

Inspect belt for wear •

Replace tine bushings •

Grease shaft bearings •

*Engine must be level when checking or lling oil. Refer to your Briggs and Stratton engine manual for proper

engine maintenance procedures.

NOT FOR REPRODUCTION

382514_B_HI

Maintenance

COMMON MAINTENANCE PROCEDURES

Note: Refer to Figure B for tools needed for common maintenance procedures outlined in this section.

Figure B

Letter Identication Tool

AImpact Wrench

B1/2” socket

C9/16” socket

D1/2” wrench

E9/16” wrench

F1/8” Allen wrench

G1/4” curved Allen wrench

HPliers

NOT FOR REPRODUCTION

382514_B_HI

Maintenance

ADJUSTING BELT TENSION

1. Loosen the mounting bolts for the engine and then slide it to apply or relieve tension on the belt.

Note: Sliding the engine forward (away from the operator) increases belt tension. Sliding the engine rear-

ward (towards the operator) relieves tension. Check and adjust belt tension after the rst 10 hours of use.

REPLACING THE DRIVE BELT

1. Lower the tines on the PL1802 unit and remove its hood. Use your hands to pull down on the rubber

latches (4 latches total; 2 in the rear of machine, 1 on each side of machine). See Figure C for latched posi-

tion and Figure D for unlatched position.

Figure C Figure D

2. Locate the wave spring attached to the tineshaft and inner pillow block bearing. See Figure E. Loosen

the set screws with an 1/8” Allen wrench. Compress the wave spring by pressing against the end plate on

the tinshaft. Once the wave spring is compressed, re-tighten the set screws. This will allow you to more

easily move the tineshaft to remove the old or worn drive belt. See Figure F.

Note: If set-screws are missing, use a 0.250”-28 sized bolt.

Figure E Figure F

NOT FOR REPRODUCTION

382514_B_HI

Maintenance

3. Loosen the inner pillow block bearings on each side of the tineshaft. Simultaneously, use the impact

wrench tted with the 9/16” socket and the 9/16” wrench to remove the hardware from each pillow block

bearing. See Figures G-J. Note the heavy weight of the tineshaft.

Figure G Figure H

Figure I Figure J

4. Use the 1/4” curved Allen wrench to remove the top belt-guide-bolt. Do not remove the bottom belt-

guide-bolt. See Figure K. Note how the belt is positioned around the pulleys in the machine.

Figure K

NOT FOR REPRODUCTION

Inhaltsverzeichnis

Andere Billy Goat Rasen- und Gartengeräte Handbücher

Billy Goat

Billy Goat CR550HC Bedienungsanleitung

Billy Goat

Billy Goat F012507A Bedienungsanleitung

Billy Goat

Billy Goat MV650SPH Bedienungsanleitung

Billy Goat

Billy Goat SC120H Kurzanleitung

Billy Goat

Billy Goat KVSP Bedienungsanleitung

Billy Goat

Billy Goat SC18OH Bedienungsanleitung

Billy Goat

Billy Goat PL25SPH Bedienungsanleitung

Billy Goat

Billy Goat QL2000VE Montageanleitung

Billy Goat

Billy Goat SC181HGEU Bedienungsanleitung

Billy Goat

Billy Goat KV600SP Bedienungsanleitung

Billy Goat

Billy Goat HTR1602V Montageanleitung

Billy Goat

Billy Goat AE403 Bedienungsanleitung

Billy Goat

Billy Goat KV600SPFB Bedienungsanleitung

Billy Goat

Billy Goat F1002SPV Bedienungsanleitung

Billy Goat

Billy Goat HTR1803VEU Montageanleitung

Billy Goat

Billy Goat SC181HEU Bedienungsanleitung

Billy Goat

Billy Goat KD502SPQ Montageanleitung

Billy Goat

Billy Goat OS900SPS Bedienungsanleitung

Billy Goat

Billy Goat MV650SPHEU Bedienungsanleitung

Billy Goat

Billy Goat PR550 Montageanleitung

Billy Goat

Billy Goat QV550HSP Bedienungsanleitung

Billy Goat

Billy Goat AET60 Bedienungsanleitung

Billy Goat

Billy Goat SV50 Montageanleitung

Billy Goat

Billy Goat MV600SPE Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung