Binatone Acura 3000 Bedienungsanleitung

Acura 3000

If you need help …

The Binatone Help Line is available

0845 345 9677

from 9.00 am to 5.00 pm, Monday

to Friday, on

Calls are charged at Local Call rate.

Or visit our website:

www.binatonetelecom.com

Unpacking your Acura 3000

Wall mount bracket

1. Where to find it

- When the instructions simply say 'press' a button, this means you should

- When the instructions say 'press and hold' a button, this means you should

Important:

- Turns ON when the TAM

is on. Flashes when you

MESSAGE light

have new TAM messages.

- Press to play back

messages and memos.

Press to pause playing of

a memo or message.

PLAY/PAUSE Button

- In standby, press to

access the caller display

CALLS (Caller Display)

Button

records.

- In standby, press and

hold to record a memo.

- During message

Button

SPEAKERPHONE Button

- Press to make, answer,

or end a call using the

speakerphone.

- In standby, press to access

- During dialling, press to

REDIAL/PAUSE Button

Microphone - For

speakerphone use and

answering machine

OGM & Memo recording.

Button

- During recording or

playback, press to stop.

hold to switch the

answering machine ON or

OFF, and when the TAM

is on press to select

OGM1 or OGM2.

(ON/OFF)

- In standby, press to play

your current OGM, or press

and hold to record a new

outgoing message.

- During playback, press

once to repeat the current

message or press twice

to skip back to the previous

message.

OGM Button

- Press to access the

Phonebook records.

(PHONEBOOK)

- In standby, press to enter the

OK / MENU Button

- You may need the Recall

function if your phone is

- When in menus or pre- dialling,

press to exit from the function.

R (Recall / Exit) Button

- Press to delete individual

messages, memos, stored

numbers or Caller Display

records.

DEL (Delete) Button

connected to a PBX, or if

you use BT Calling Features.

Time and other phone/TAM

- When setting options,

- During a call, press to

- In standby, press and

- This flashes when the phone is

ringing for an incoming call.

Ringer light

Options Menu to set the Date,

- During speakerphone or

- In lists, press to step

VOL+ , VOL-

through options.

Button

(UP/DOWN) Buttons

the Redial list.

press it briefly then release it.

keep it pressed until the display changes or you hear a tone.

mouthpiece.

mute the microphone or

TAM operation, press to

adjust the volume.

playback, press to skip

to the next message.

MUTE Button

insert a pause

settings.

press to confirm a choice.

SPEAKERPHONE light

- Turns on when the

speakerphone is on.

Phone You are connected to the telephone line - your

Handset is ‘offhook’.

Time Displays the time.

Date/Month Displays the date and month.

Speakerphone Appears when the speakerphone function is

turned ON.

Message Appears when viewing a Caller display entry

where an answering machine message was

NEW records.

Caller Display

Record

Shows the position in the Caller Display list of

being received or

viewed.

mute the mouthpiece or microphone.

Appears when viewing New Caller Display

recorded.

Indicates the total number of answering machine

messages recorded (XX from 00 to 59) and the

total number of caller display records saved (YY

from 00 to 99) .

Flashing alternately with the screen above,

indicates the number of new answering machine

messages recorded and the number of new

MESSAGES CALLS

XX YY

NEW NEW caller display records received.

the caller display record

It shows theNumber field:

telephone number and the

number of messages.

It shows the name

and the status of a call/message.

Letter field:

Flashes when you press the MUTE button to

2. Plug the coiled handset cord into the Handset. Plug the other end into

the socket on the side of the Base unit.

3. Place the Handset on

the Base unit.

4. Plug the telephone line cord into

the PHONE LINE socket at the

end into your telephone line socket 5. Plug the power supply cord into

the POWER jack at the back of

into a 230V AC, 50Hz mains

socket, with the switch on the

socket set to OFF

6.Switch ON the mains power at

the socket. Wait while the

7.Lift the Handset and check

or extension socket.

display shows INITIALISATION,

standby screen.

back of the Base unit. Plug the other

forDial tone in the earpiece.

the Base unit. Plug the other end

then the announcement

2. Installation

Make sure the plugs

click into place.

1. Locating the Base unit

The Base unit should be placed on a level surface, in a position where:

the mains adapter plug will reach an easily accessible 230-V AC

extension socket.

might get wet.

machines, microwave ovens, TVs, fluorescent lights, etc.

cable.

the telephone line cable will reach your telephone line socket or

it is not close to a sink, bath or shower, or anywhere else where it

switched mains supply socket - never try to lengthen the mains power

it is not close to other electrical equipment - fridges, washing

“Answering machine on.

Announcement one”

before the display changes to the

Base unit must be used only

with the AC power adapter

Shen Zhen G.EREDIT Electronics Co.,Ltd.

5E-AD070042-B.

Note: The base unit doesn't require a battery.

Always use the telephone line

cord supplied with your Phone.

Other telephone line cords may

not work.

to Telephone

line socket

RINGER

HI/LOW

switch

Note: The Acura 3000

If you have a Broadband line

If you connect your telephone to

a line with a broadband

connection, you will need to

insert a micro-filter between the

telephone and the telephone line,

otherwise you may get

interference between the telephone and the broadband, which could cause

problems.

In a home with broadband, every telephone must have a micro-filter connected,

not just the one at the telephone point that your modem is connected to.

If you need more broadband micro-filters, contact your broadband supplier.

To place the Acura 3000 on a wall, connect the

wall mount bracket to the bottom of the phone in

Wall Mount

3. Wall mount installation

Insert the rigid clips of the bracket into the slots on the

bottom of the phone (nearer the front of the base).

Press down firmly until the flexible clips click into place

in the slots nearer the centre of the base.

To remove the bracket, (1)

(2) (3)

forward as shown below. slide up and

the slots near the front of the base as shown

below.

pinch the flexible clips,

pull back the bracket, and then

Wall mounting continue...

Mark two points on the wall that are 80 mm

apart to lay the fixing centres as shown below.

BE CAREFUL to check that there are no pipes or

Fix two screws (7mm head screws required, not

supplied) at the marked locations, leaving

approximately 7mm between the wall and the

screw head.

Hang the telephone on the screws using the wall

mount slots.

Place the Handset on the cradle with

parking recess

so that the Telephone is securely fixed and does

not wobble.

parking hookthe on the cradle arranged to fit in

the under the earpiece on the

Handset.

80 mm

electrical wires hidden in the wall.

You may need to adjust the screws

Binatone Help Line - 0845 345 9677

Calls are charged at Local Call rate.

The following section details how to set up your telephone.

Note: The system will time out if you leave more than

10 seconds between key presses.

With the phone in standby mode;

OPTIONS MENUOPTIONS MENU

OPTIONS MENU

SET

LANGUAGE

EXIT OPTIONS

ÖTo set the Answering Machine

Setting up the Acura 3000

Press the OK/MENU button to enter the Options menu and

then use the UP or DOWN buttons to cycle through the

following options:

recording quality / total recording time. (ON gives up

minutes of lower quality.)

to 20 minutes of higher quality, OFF gives up to 40

Press the OK/MENU button.

ÖThe display shows

SET LANGUAGESET LANGUAGE

SET LANGUAGE

Continue with programming, or press the /

button to return to standby mode.

Press the OK/MENU button to confirm.

Press the UP button to go to the language setting.

The display shows

Press the UP or DOWN button to select ENGLISH

(default), FRANCAIS, or DEUTSCH.

Press the OK/MENU button to confirm.

SET LANGUAGE

SET TIME/DATE

SET FLASH TIME

LCD CONTRAST

MESSAGE LENGTH

RINGS TO ANSWER

REMOTE ACCESS

TAM HD: ON/OFF

Binatone Help Line - 0845 345 9677

Calls are charged at Local Call rate.

SET TIME/

DATE

Setting up continue...

1ÖThe display shows

OPTIONS MENUOPTIONS MENU

OPTIONS MENU

SET TIME/DATESET TIME/DATE

SET TIME/DATE

5Press the OK/MENU button to confirm.

Press the UP or DOWN button to set the year.

Press the UP or DOWN button to set the month.6

Press the OK/MENU button to confirm.

Press the UP or DOWN button to set the date.8

Press the UP or DOWN button to set the hour.10

Press the OK/MENU button to confirm.11

Press the UP or DOWN button to set the minutes.12

Press the OK/MENU button to confirm the TIME13

14 Continue with programming, or press the /

button to return to standby mode.

(see section 9) the time and date will be set

automatically, but the year may still need to be

Note: If you subscribe to the caller display service

stamp gives the correct day.

adjusted to ensure the answering machine time

Press the OK/MENU button.

Press the UP or DOWN button until the display

shows

and DATE setting.

The 'minutes' will be blinking.

When setting the 'hour it is in 24 hour

mode only.

Press the OK/MENU button to confirm.

The 'hour' will be blinking.

Press the OK/MENU button to confirm.

The 'date' will be blinking.

The 'year' will be blinking.

The 'month' will be blinking.

Binatone Help Line - 0845 345 9677

Calls are charged at Local Call rate.

Press the OK/MENU button.

ÖThe display shows

OPTIONS MENUOPTIONS MENU

OPTIONS MENU

Press the UP or DOWN button until the display

shows

SET FLASH TIMESET FLASH TIME

SET FLASH TIME

3Press the OK/MENU button to confirm.

SET FLASH

TIME

4Press the UP or DOWN button to select 100MS

(default), 300MS, 600MS or 1000MS.

Setting up continue...

5Press the OK/MENU button to confirm.

6Continue with programming, or press the /

button to return to standby mode.

1Press the OK/MENU button.

ÖThe display shows

OPTIONS MENUOPTIONS MENU

OPTIONS MENU

2Press the UP or DOWN button until the display

shows

LCD CONTRASTLCD CONTRAST

LCD CONTRAST

3Press the OK/MENU button to confirm.

4 Press the UP or DOWN button to select your

comfortable display viewing level (1-5). The

default setting is 3.

5 Press the OK/MENU button to confirm.

6 Continue with programming, or press the /

button to return to standby mode.

LCD

CONTRAST

You may need the Recall function if your phone is

connected to a PBX, or if you use BT Calling

Features.

Flash is another name for the R (Recall) button,

and the normal UK requirement is for 100ms, but

some PBX may need a longer time, in which case

you can change the setting from the Options Menu.

Andere Handbücher für Acura 3000

Inhaltsverzeichnis

Andere Binatone Telefon Handbücher

Binatone

Binatone LYRIS 110 Bedienungsanleitung

Binatone

Binatone Speakeasy 6 Bedienungsanleitung

Binatone

Binatone 3488 Bedienungsanleitung

Binatone

Binatone Veva 1210 Bedienungsanleitung

Binatone

Binatone CAPRICE CAPRICE 600 Bedienungsanleitung

Binatone

Binatone Speakeasy 17 Bedienungsanleitung

Binatone

Binatone Oval Twin XD1220 Bedienungsanleitung

Binatone

Binatone CAPRICE 500 Bedienungsanleitung

Binatone

Binatone 2102 Bedienungsanleitung

Binatone

Binatone Caprice 670 Bedienungsanleitung

Binatone

Binatone iDECT M3i Bedienungsanleitung

Binatone

Binatone IHOME PHONE - Bedienungsanleitung

Binatone

Binatone SPEAKEASY 5 Bedienungsanleitung

Binatone

Binatone Caprice 670 Bedienungsanleitung

Binatone

Binatone PB10 Bedienungsanleitung

Binatone

Binatone Speakeasy Combo 3865 Triple Bedienungsanleitung

Binatone

Binatone Speakeasy Combo 3410 Bedienungsanleitung

Binatone

Binatone 5502 Bedienungsanleitung

Binatone

Binatone Acura 3000 Bedienungsanleitung

Binatone

Binatone Spirit 410 Bedienungsanleitung

Binatone

Binatone iDECT Freedom Twin Bedienungsanleitung

Binatone

Binatone ACTIVE XA2020 Bedienungsanleitung

Binatone

Binatone LYRIS 310 Bedienungsanleitung

Binatone

Binatone LYRIS 410 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung