Bircher Reglomat EsGate 2 Bedienungsanleitung

When everything is connected correctly:

Status LED lights up green

Mode

Data

Original operating instructions (translation)

Safety an warning notices

EsGate 2, EsGate 2.LVAC

«Data» button

Version Operating vo tage safety edge safety edge Test input Output 1 Output 2 Signa output

EsGate 2

EsGate 2.LVAC

+/~

–/~

➔The electrical connection may only be set up by an electrician. ➔The arrangement of the components depends on the structural conditions and the

gate design. ➔Switch off the operating voltage before working on the system. ➔The switching device monitors pressure-sensitive protective devices

from Bircher Reglomat AG (proper use). ➔Use of components not supplied by Bircher-Reglomat (including safety edges) will render the guarantee and

liability null and void. ➔Connect all operating and switching voltages to the same fuse. ➔Connect the operating voltage to the same circuit as the indu-

strial door controller. ➔Disconnect device from mains in the event of a fault. ➔Protection max. 10 A

Switching device in combination with safety edges to

avoid dangers at crushing and shearing points in sliding gate systems

Electrical connection an terminal iagram

Operation Display

Dots

flash

Control buttons

on device:

Displays shown when safety edge is actuated: Status LED lights up orange

actuated: actuated:

«Mode» button

Stan ar operation

Please keep for futurereference!

ENGLISH

Diagnostic menu

Press the «Mode»and «Data»buttons simultaneously for 2 s ➔status LED flashes orange. Press «Mode»buttons briefly to change to the next

mode. Press the «Mode»button for 2 s to exit diagnostic menu.

Mode «r» Resistance

Error display mode

The 5 most recent errors

can be interrogated. Press

The resistances of the

safety edges are dis-

the «Data»key briefly in each

case, and the errors are dis-

played one after the other. End

appears when the «Data»button

is pressed for the 5th time. The

malfunctions are displayed in

chronological order (new ➔old)

played. Example:

8 = Resistance between

7 and 9 kohm.

1 = safety edge 

To access the next safety edge:

Press the «Data»button

CLOSE Output

OPEN Output

Mode

Data

Dots

Configuration mo e (for configuration before starting up, via diagnostic menu, after mode «h»)

Please read chapters 5.1 to 5.4 in full before attempting configuration.

Activating configuration menu

5.1

Status LED flashes orange,

press «Data» button

Press the «Mode» and «Data» buttons

simultaneously for 2 s.

Configuration menu is activated.

Configuration of safety edge inputs

5.2

Use the «Data» button to set the configuration

you want for the safety edge inputs

(according to Table 1).

The current setting for the safety

edge inputs is displayed.

Dysplay safety edge safety edge 

not configured

001* X X

002 X

003 X

UNC

*) Factory setting

Configuration menu can be exited at any time by pressing the «Mode» button (2 s).

«End» is displayed ➔Press «Data» button and release ➔Restart undertaken with new configuration.

Tab e 1

= Symbol for display flashes

Output 1: Press the

«Data»button

The Output 1

is deactivated

The Output 1 is

activated

Press the «Data»

button again

Mode «S» Output 1 Mode «S» Output 2

Both outputs: Press

the «Data» button

Both outputs are

deactivated

Both outputs are

activated

Press the «Data»

button again

Mode «I» Test input Mode «C» current

configuration

Mode «C» current configuration

test signal

Mode «h» current

fall-delay time

Modus «S» Simulation test

Display when

test input inactive

Display when

test input active

Displays current configu-

ration of safety edge

inputs, see configuration

table.

Displays current configura-

tion, test signal,

see test pulse table.

Displays current fall-delay

time, see fall-delay time

table.

Configuration ➔chapter 5 Configuration ➔chapter 5

Configuration ➔chapter 5

Active test input:

To access the config. mode:

Proess the «Mode» button

Output 2: Press the

«Data»button

The Output 2

is deactivated

The Output 2 is

activated

Press the «Data»

button again

Most important technical ata

Operating vo tage

EsGate 2 24 V AC/DC ± 15%,

EsGate 2.LVAC 100-240 V AC

50/60 z

Power consumption max. 3 VA

Safety edges 8,2 kOhm

Disp ay E001 E002 E006 E101/ E102

Error Safety edge malfunct.



Safety edge malfunct.



Mounting ≠config. mode Undervoltage/overvoltage

Remedy Check safety edge



Check safety edge



Check configuration Check supply

Error isplays

If an error is detected then the outputs are deactivated and symbols &and an error code are displayed. The status LED lights up red.

Should other fault messages appear, please contact your supplier.

Configuration fall- elay time

5.4

Display Fall-delay time

001 none

002 100 ms

003*200 ms

004 500 ms

005 1000 ms

Use the «Data» button to set the required fa -de ay time (according to Table 3).

Then briefly press the «Mode» button and End appears.

➔The system is configured.

➔Press «Data» button to restart.

*) Factory setting

Tab e 3

Error messages may occur when restarting

after configuration if the inputs do not match

the configuration.

Manufacturer: Bircher Reglomat AG, Wiesengasse 20, C -8222 Beringen

Employee responsible for documentation: Bircher Reglomat AG, Wiesengasse 20, C -8222 Beringen

Product: Switching device with inductive transmission system

Models: InTra6 2, InTra6 2.LVAC, InTra6 3, InTra6 3.LVAC; EsGate 2, EsGate 2.LVAC, EsGate 3, EsGate 2.LVAC (without transmiss.)

Serial numbers: 00240578[000000…900000], 00244423[000000…900000], 00263915[000000…900000],

00263916[000000…900000], 00263911[000000…900000], 00263912[000000…900000],

00263913[000000…900000], 00263914[000000…900000]

Notified Body: SUVA certificate authority, division: technics, EU-ID-number 1246

EC-type-examination certificates: E 6934 – E 6937

Following directives have been observed: Machinery directive 2006/42/EG, R&TTE Directive 1999/5/EG

Following standards have been taken

into account: EN ISO 13849-1, EN 12978

Signee: CEO, L. Oberholzer / Q SE, K. Kuhn, 18.8.2010, C -8222 Beringen

EC Declaration of conformity, ate of pro uction

260279D12/10

Configuration Test input

5.3

Use the «Data» button to set

the required test signa

(according to Table 2).

Display Test pulse

001

002*

Tab e 2 *) Factory setting

Outputs Semiconductor relay, 24 V DC, max. 50 mA

Test input 24 V DC ± 15% 2 mA

Not activated = Standard operation, activated = Test

Dimensions

(W x H x D) 22,5 x 94 x 88 mm

Signal output

Signal output closed when both outputs, 1 and 2, are closed. Actuation or fault ➔signal output open.

EC Declaration of conformity

9.1

Date of pro uction

9.2

See label ➔week/year, e.g. 12/10 = week 12, 2010

Manufacturer:

Bircher Reglomat AG

Wiesengasse 20

CH-8222 Beringen

Switzerlan

www.bircher-reglomat.com

Authorise representative:

Bircher Reglomat GmbH

Robert-Bosch-Strasse 3

D-71088 Holzgerlingen

Germany

www.bircher-reglomat.com

Contact ata

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bircher Reglomat Sicherheitssensor Handbücher

Bircher Reglomat

Bircher Reglomat MERKUR SE Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat ProLoop 2 Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat Herkules 2E Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat ProLoop Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat PrimeMotion C Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat Jupiter Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat ESM Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat ProxySwitch Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat ProLoop Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat PrimeScan B Beilage

Bircher Reglomat

Bircher Reglomat PrimeTec B Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat MERKUR Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat Merkur 2 Series Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat RK 31C-PWH Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat Reflex ES Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat Hercules 2 Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat ProLoop Lite Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat EasyMotion Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat Herkules 2 Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat PrimeTec B Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat US beam Beilage

Bircher Reglomat

Bircher Reglomat PrimeMotion B Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat RBM 2 Bedienungsanleitung

Bircher Reglomat

Bircher Reglomat DI1-Pro V2 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung