Bircher Reglomat ProLoop Lite Bedienungsanleitung
1
85
22.5
92
ProLoop Lite
Loop detector for industrial doors and gates and car parks
Translation of the original instruction
General
1Safety instructions
3Connect electrical equipment
2Mechanical mounting in the switch cabinet
ENGLISH
354822B
06/16
i
Information – light emitting diode
LCD display
“Mode” key
“Data” key
Connecting terminals
Type plate
– These devices and their accessories may only be operated in accordance
with the operating instructions (intended use).
– These devices and their accessories may only be placed in operation by
trained and qualied personnel.
– These devices may only be operated with the operating voltages and
parameters intended for them.
– If malfunctions occur that cannot be eliminated, place the device out of
operation and send it in for repair.
– These devices may only be repaired by the manufacturer. Tampering and
alterations are not permitted. This will invalidate all guarantee and war-
ranty claims.
The ProLoop Lite is mounted in the switch cabinet on a 35 mm H-rail in accordance with EN 50022. The terminals can be plugged in and coded.
The loop connection wiring to a loop detector must be twisted at least 20 times per meter.
Please wire the device according to the wiring diagram.
Ensure correct assignment of the terminals and that the power supply is right in accordance with the type plate on the device.
Power supply Loop connection
1-channel device
Loop connection
2-channel device
Output 1 Output 2
˜⁄
+
˜⁄
−
A1
A2
L3
L4
L3
L4
L5
L6
1
2
14
11
12
no
nc
common
24
21
22
no
nc
common
4Value and parameter setting options
General
The settings of the ProLoop Lite devices in this chapter are depicted and explained using the 1-loop device.
The settings for loop 2 of a 2-loop device should be made using the corresponding method.
3.1 Terminal connection diagram
2
4.1 Value and parameter setting options
4.2 Basic functions of output relay status 0(setting, see table 4.8)
4.3 Time functions 1, time unit 2and time factor 3 (settings, see table 4.8)
4.4 Sensitivity 4(setting, see table 4.8)
4.5 Automatic sensitivity boost ASB S(setting, see table 4.8)
4.6 Frequency 6(setting, see table 4.8)
4.7 Switching from operating to conguration mode
Standard display
1-loop device
Standard display
2-loop device
112
Explanation of the LEDs
Info
Red + Green Start-up phase
conguration
Green Operation
Green ashing Output 1 or / and
2 activated
Flashing red Error
Explanation of the LCD display
Loop 2
Loop 1
Function
Example:
Time
function set
12
Example:
Parameter
“h” set
Parameter Loop unactivated Loop activated Fault
1Door and gate
2Barrier
3Quiescent
current
Activation of the
loop pulls the relay
on; the relay drops
off when the loop
is exited. t = typically ms or s
Switch-on delay:
When the loop is
activated, the relay is
pulled on after the time t
and drops off when the
loop is exited.
t
t = typically ms or s
Switch-o delay:
When the loop is
activated, the relay is
pulled on drops off after
time t tafter the loop is
exited.
t
t = typically ms or s
Activation pulse:
When the loop is
activated, the relay
is pulled on and
drops back off
after time t.
t
t = typically ms or s
Exit pulse:
When the loop is exited,
the relay is pulled on and
drops back off after time
t.
t
t = typically ms or s
Maximum presence:
When the loop is
activated, the relay is
pulled on and drops back
off when exited, but not
later than after time t.
t
t = typically ms or s
The sensitivity Sof the loop detector can be adjusted in 9 steps:
S1 = lowest sensitivity
(➝much metal, low recognition distance)
S9 = highest sensitivity
(➝ little metal, large recognition distance)
S4 = factory setting
ASB (= Automatic Sensitivity Boost).
ASB is required in order to be able to detect trailer drawbars after activation.
Four different frequencies F1, F2, F3 and F4 can be set. This helps to prevent crosstalk with adjacent loops. Factory setting: F4.
1-loop device
Display after
start-up:
1Touch the «Mode» button
once to change to configura-
tion mode
Mode 1
2-loop device
Display after
start-up:
12Touch the «Mode» button
once to change to configura-
tion mode
Mode 1
Loop 1 is
selected
Mode 2
Loop 2 is selected
(Back to automatic mode: Press and hold Mode button > 1 second)
Loop
Relay
Loop
Relay
Loop
Relay
Loop
Relay
Loop
Relay
Loop
Relay
3
Table Settings Button
operation
parameter
Data Data Data Data Data Data
Function LCD
Display
Button operation
functions
AOperating
mode
1
Mode
Operating mode 1
0Basic function 1
Mode
Door and gate* 1Barrier
1
Quiescent current 1
1Time function 1
Mode
∞* 1Switch-on delay
t
1
Switch-off delay
t
1Loop activation
pulse
t
1Loop exit pulse
t
1Maximum
presence
t
1
2Time unit
1
Mode
With time
function th (∞),
this display
does not appear
0.1 second 11 second*
1
1 minute 11 hour 1
Note:
Time unit multiplied by time factor
gives the set time.
3Time factor 1
Mode
With time
functionth(∞),
this display
does not appear
1 * 1
Set value between 1 and 99 by touching or holding the «Data» button
4Sensitivity 1
Mode
S
Sensitivity =
responsiveness
4 * 1
Set value between 1 (lowest ) and 9 (highest sensitivity) by touching or holding the “Data” button
5Automatic
sensitivity
boost ASB
1
Mode
ASB stands for
Automatic
Sensitivity
Boost
Switched off* 1Switched on 1
6Frequency 1
Mode
Frequency F1
1
Frequency F2
1
Frequency F3 1Frequency F4* 1
*Factory setting
Loop
Relay
Loop
Relay
Loop
Relay
Loop
Relay
Loop
Relay
Loop
Relay
4.8 Conguration mode
Note on 2-loop device: For each function after Loop 1 is set, the parameters of Loop 2 are set (perform settings similarly).
4
5Error display
6Reset
7Technical data
8EC Declaration of Conformity
9Contact
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen
Following directives have been observed: RoHS 2011/65/EU, RED 2014/53/EU
Product variants: ProLoop Lite 1.x, ProLoop Lite 2.x
Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
www.bircher-reglomat.com
When an error occurs, the operating mode “A” and the error display “E” are shown alternatingly.
The LED changes to ashing red.
Mode
2 seconds Reset 1 (recalibration)
The loop(s) is/are recalibrated.
Power supply
voltage/
power consumption
24 VDC 24 VDC -10% to +20%,
max. 1.5 W
230 VAC 230 VAC ± 10%, 50 Hz,
max. 2.9 VA
Loop inductiveness Max. 20 to 1000 µH
Ideally 80 to 300 µH
Loop power line For 20-40 µH: max. 100 m with 1.5 mm2
For >40 µH max. 200 m with 1.5 mm2
Min. twisting 20 times per metre
Loop resistance < 8 ohms with connection wire
Output relay (loop) Max. 240 VAC; 2 A / 30 VDC; 1 A; AC-1
Dimensions 22.5 x 92 x 85 mm (W x H x D)
Housing mounting Direct DIN rail mounting
Connection type Screw-in terminals
Protection class IP 20
Operating
temperature
-20°C to +60°C
Storage
temperature
-40°C to +70°C
Air humidity < 95% non-condensing
Danish seller:
Swissdoor ApS
Stenhuggervej 2
DK-5471 Soendersoe
Denmark
Tel.: +45 86 28 00 00
www.swissdoor.dk
Andere Bircher Reglomat Sicherheitssensor Handbücher
Bircher Reglomat
Bircher Reglomat PrimeMotion C Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat PrimeTec B Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat PrimeMotion B Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat RBM 2 Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat DI1-Pro V2 Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat MERKUR Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat Jupiter Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat RK 31C-PWH Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat Hercules 2 Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat ProLoop Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat Herkules 2E Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat ProxySwitch Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat Swissdoor PrimeMotion B Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat PrimeScan B Beilage
Bircher Reglomat
Bircher Reglomat EasyMotion Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat PrimeTec B Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat ProLoop Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat Reflex ES Bedienungsanleitung
Bircher Reglomat
Bircher Reglomat US beam Beilage
Bircher Reglomat
Bircher Reglomat ProLoop 2 Bedienungsanleitung
