Black & Decker Surge Xpress F855 Montageanleitung

Surge ™

Iron

SAVE THIS USE AND CARE BOOK

1-800-231-9786

QUESTIONS? Please call us TOLL FREE!

MODEL F855/F855S

When using your iron, basic safety precautions should always be followed,

including the following:

■Read all instructions.

■Use iron only for its intended use.

■To protect against a risk of electric shock, do not immerse the iron in

water or other liquid.

■The iron should always be turned to No Heat/Fill before plugging into or

unplugging from an outlet. Never yank cord to disconnect from outlet;

instead, grasp plug and pull to disconnect.

■Do not allow cord to touch hot surfaces. Let iron cool completely

before putting away. Loop cord around cordwrap when storing.

■Always disconnect iron from electrical outlet when filling with or

emptying water and when not in use. Be careful to avoid spilling water

over iron when filling.

■Do not press the Self Clean button while ironing.

■Do not operate iron with a damaged cord or plug or if the iron has been

dropped or damaged. To avoid the risk of electric shock, do not

disassemble the iron; instead, take it to an authorized service center for

examination and repair. Incorrect reassembly can cause a risk of

electric shock when the iron is used.

■Close supervision is necessary for any appliance being used by or near

children. While connected, do not leave iron unattended or on an

ironing board. Always position iron carefully to prevent it from falling if

ironing board is accidentally moved or cord is pulled. Always use heel

rest.

■Burns can occur from touching hot metal parts, hot water, or steam.

Use caution when you turn a steam iron upside down — there may be

hot water in the water tank. Avoid rapid movement of iron to minimize

hot water spillage.

■Do not operate in the presence of explosive and/or flammable fumes.

■The use of attachments not recommended or sold by the appliance

manufacturer may cause fire, electric shock, or injury.

■Do not use iron outdoors.

■This product is for household use only.

IMPORTANT SAFEGUARDS

SPECIAL INSTRUCTIONS

■To avoid a circuit overload, do not operate another high-wattage

appliance on the same circuit.

■If an extension cord is necessary, use a 10-ampere rated cord with a

polarized plug and Underwriters Laboratories listing. Cords rated for

less amperage may overheat. Care should be taken to arrange the cord

so that it cannot be pulled on or tripped over.

POLARIZED This appliance has a polarized plug — one

PLUG blade is wider than the other. To reduce

the risk of electric shock, this plug will fit

into a polarized outlet only one way. If the

plug does not fit fully into the outlet,

reverse it. If it still does not fit, contact a

qualified electrician. Do not attempt to

defeat this safety feature by modifying the

plug in any way.

This appliance is equipped with a tamper-

resistant screw to prevent removal of the

outer cover. To reduce the risk of fire or

electric shock, do not attempt to remove

the outer cover. There are no user

serviceable parts inside. Repair should be

done only by authorized service personnel

(see pages 14 & 15 for a list of Black &

Decker Company-Owned Service Centers).

SAVE THESE INSTRUCTIONS

TAMPER-

RESISTANT

SCREW

1. Water Fill - see page 6

2. Push to Clean Setting - see page 10

3. Adjustable Steam Control - see page 7

4. Surge of Steam Control - see page 7

5. Heat/Fabric Dial - see page 6

6. ON/OFF Control and Power On Light

- see page 6

7. Cordset and Cordwrap - see page 8

8. Heat/Fabric Setting Indicator - see page 6

9. Water Tank - see page 6

10. Soleplate - see page 10

PREPARING IMPORTANT: Follow this procedure to clean the

YOUR IRON iron and to become familiar with its features.

1. Remove any labels, stickers, or tags which

may be attached to the body or soleplate of

the iron.

2. Fill Water Tank about 1/3full with water.

(See “Filling With Water,” page 6.)

3. Plug iron into a standard polarized electrical

outlet.

4. Set the Heat/Fabric Dial to the Cotton/Linen

setting and preheat for about 2 minutes.

(See “Starting The Iron,” page 6.)

5. Iron on an old cotton terry cloth towel for

about two minutes, and use each of the

iron’s features.

Surge of Steam: Pump the Surge of Steam

Button every 5 seconds to see the amount of

steam that will be generated.

Steam Settings: Turn the Steam Control to

the (light), (medium), and

(heavy) settings to become familiar with the

different amounts of steam at each setting.

6. Use the Self-Cleaning feature as described

on page 10.

7. Plug the iron in and place on its Heel Rest.

Heat for about 2 minutes to dry out any

remaining water after Self-Cleaning.

How To Use

FILLING WITH WATER

1. Using a clean cup, pour water

into the Water Fill until the

water level reaches the top of

the Water Tank (Figure A). Do

not overfill. Refill as necessary.

2. Ordinary tap water can usually

be used for ironing. However,

do not use water processed

through a home softening

system.

3. In extremely hard water areas

(over 180 parts per million),

consider using distilled or

demineralized water. If using

distilled or demineralized water,

tap water should be used the

first time you use the iron and

once per month thereafter to

maintain steam performance.

STARTING THE IRON

1. Plug in the iron.

2. Press the ON/OFF Button

(Figure B).

3. Select the heat setting for the

fabric to be ironed. (See Fabric

Ironing Chart on page 9 or the

Heat Fabric Guide on the iron.)

4. Turn the Heat/Fabric Dial to the

Setting Indicator (Figure C).

Allow approximately 45 seconds

for the iron to preheat.

5. Unless the Power On Light is

already on, you must press the

ON/OFF Control to start the iron.

6. The iron will automatically shut

off after one hour. (Figure D).

Figure A

Figure B

Figure C

Fill

To Here ●

ONE-HOUR AUTO OFF FEATURE

1. This iron will shut off

automatically after one hour

whether you are using it or

have left it plugged in

unattended.

2. If you have ironed for less than

an hour and would like to

manually shut the iron off, push

the ON/OFF button or simply

unplug the cord. Otherwise, the

iron will shut off automatically

after it has been on for an hour.

DRY IRONING

1. Turn the Adjustable Steam

Control to DRY to iron without

steam.

STEAM IRONING

USING MOISTURE

1. Make sure the Heat/Fabric Dial

is set within the Steam area.

2. Turn the Adjustable Steam

Control (Figure E) to the

(light), (medium), and

(heavy) steam setting as

indicated in the band over the

fabric setting (See Figure C).

3. If water spotting occurs,

reduce the steam level. If

necessary, increase the heat

setting by turning the Heat/

Fabric Dial to a slightly higher

setting if the fabric will allow it.

SURGE OF STEAM

1. Pump the Surge of Steam

Control (Figure F) several times

Figure E

Figure D

1 Hour Auto-Off

Figure F

to get an extra heavy surge of

steam through the soleplate

steam vents.

2. Use Surge of Steam only when

the Heat/Fabric Dial is set in

the steam range.

3. To avoid water spotting, wait a

few seconds between

repeated use of the Surge of

Steam.

STORING THE IRON

1. Turn the Adjustable Steam

Control to DRY.

2. Turn the Heat/Fabric Dial to Fill.

3. Unplug the iron.

4. Allow the iron to cool and wrap

the cord. (Figure G).

5. It is not necessary to empty the

water if the iron is used

frequently.

6. The iron must be stored on its

heel rest to prevent water

leaking from the soleplate.

FABRIC IRONING Refer to the chart on the next page for

CHART recommended Heat/Fabric and Steam

Settings and ironing instructions for

various fabrics. Always read garment labels

and follow manufacturer’s ironing

instructions.

NOTE: Steam and Surge of Steam should only

be used in steam area of the Heat/Fabric Dial.

Water spotting may occur if the setting is too

low.

Figure G

Care Of The Iron

EMPTYING THE IRON

1. Turn the Heat/Fabric Dial to Fill.

2. Set the Adjustable Steam Control

to the Dry position, and unplug

the iron.

3. Empty the water by holding the

iron over a sink with the tip

pointing downward (Figure H).

Water will empty out of the

Water Fill.

4. If all the water has not drained,

repeat the emptying process.

HEAT/FABRIC ADJUSTABLE STEAM

SETTING SETTING INSTRUCTIONS

No Heat

Fill

Acrylic Dry iron on wrong side of fabric.

Acetate Press washables while damp.

Dry

Silk Dry Iron on wrong side of fabric to prevent shine.

Nylon Press washables while damp.

Polyester Dry Iron washables while fabric is damp.

Rayon Iron Iron rayon fabrics on the wrong side.

At Light Steam iron if fabric manufacturer directs.

Any

Cotton Setting Check care label and follow the manu-

Blends facturer’s instructions for blends; use

Medium the setting for the fiber requiring the

Wool lowest heat.

Blends Use a press cloth to prevent shine.

Wool Steam iron on the wrong side of fabric to prevent

shine, or use a press cloth on right side.

Do not press completely dry.

Cotton Heavy Dry iron washables while damp. Use steam

Linen as needed. Iron dark fabrics on wrong side of

fabric to avoid shine.

Figure H

CLEANING 1. Allow the iron to cool completely.

THE OUTSIDE 2. For model F855, clean the Soleplate with a

paste of mild scouring powder and a little

water. Apply a small amount of paste to the

Soleplate with a damp cloth. Rub the soiled

area and wipe clean with a damp cloth.

3. For model F855S, wipe the non-stick coated

Soleplate with a cloth dampened in water

and a mild detergent. Never use abrasives,

heavy-duty cleansers, or scouring pads.

4. After cleaning, steam iron over an old cotton

terry cloth towel for approximately 2 minutes.

SELF CLEANING

1. About once a month, use the

Self-Clean and Surge of Steam

features to flush out water,

minerals, and lint. If lint is

allowed to accumulate in the

vents, it can scorch and cause

troublesome brown spotting.

Do not be alarmed if hissing and

spitting occurs while self

cleaning. This is normal.

2. Be sure the Water Tank is about

1/3full (filled to the Setting

Indicator).

3. Set the iron on its heel rest.

Then heat at the highest

temperature setting for about

2 minutes.

4. Turn the Adjustable Steam

Control to Dry and use the

Surge feature 2 to 3 times.

5. Unplug the iron.

6. Hold the iron in the ironing

position over a sink or basin.

7. Turn the Adjustable Steam

Control to the Push to Clean

setting. (Figure I).

Figure I

SURFACES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black & Decker Eisen Handbücher

Black & Decker

Black & Decker X815 Bedienungsanleitung

Black & Decker

Black & Decker The Classic F63D Series Montageanleitung

Black & Decker

Black & Decker X2150 Bedienungsanleitung

Black & Decker

Black & Decker SteamXpress AS675 Montageanleitung

Black & Decker

Black & Decker F150 Bedienungsanleitung

Black & Decker

Black & Decker Avant Steam F990 Montageanleitung

Black & Decker

Black & Decker STEAMADVANTAGE IR1070S Bedienungsanleitung

Black & Decker

Black & Decker SteamXpress AS200 Montageanleitung

Black & Decker

Black & Decker XT2000 Bedienungsanleitung

Black & Decker

Black & Decker F200 Bedienungsanleitung

Black & Decker

Black & Decker The Classic F63D Series Montageanleitung

Black & Decker

Black & Decker Light 'n Easy F495SA Montageanleitung

Black & Decker

Black & Decker Elite Digital Pro Series Bedienungsanleitung

Black & Decker

Black & Decker The Classic F63E Montageanleitung

Black & Decker

Black & Decker D2000 Series Montageanleitung

Black & Decker

Black & Decker X850 Bedienungsanleitung

Black & Decker

Black & Decker IR04VC Bedienungsanleitung

Black & Decker

Black & Decker QUICK 'N EASY IM200 Montageanleitung

Black & Decker

Black & Decker Quick 'N Easy IM310 Montageanleitung

Black & Decker

Black & Decker BXSS2400E Bedienungsanleitung

Black & Decker

Black & Decker SteamAdvantage F2000 Montageanleitung

Black & Decker

Black & Decker Light 'N Easy F975 Montageanleitung

Black & Decker

Black & Decker X300 Montageanleitung

Black & Decker

Black & Decker IR34V Firmware-Update

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung

dyras

dyras ESI-2400AC Bedienungsanleitung

Philips

Philips PerfectCare PSG71 Series Bedienungsanleitung

GE 169061 Bedienungsanleitung