Black Box LB303A Bedienungsanleitung

May, 2008

Hardened VDSL Ethernet Extender

LB303A

Order toll-free in the U.S. Call : 877-877-BBOX ( Outside U. S. call 724-746-5500 )

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax

724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]m

CUSTOMER

SUPPORT

INFORMATION

Hardened VDSL Ethernet Extender

FEDERAL COMMUNICATIONS COMMISSION AND

CANADIAN DEPARTMENT OF COMMUNICATIONS

RADIO FREQUENCY INTERFERENCE STATEMENT

Class B Digital Device. This equipment has been tested and found to comply with the limits for a

Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. However,

there is no guarantee that interference will not occur in a particular installation. This equipment

generates, uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. If this

equipment does cause harmful interference to radio or telephone reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult an experienced radio/TV technician for help.

Caution:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

To meet FCC requirements, shielded cables and power cords are required to connect this device

to a personal computer or other Class B certified device.

This digital apparatus does not exceed the Class B limits for radio noise emission from digital

apparatus set out in the Radio Interference Regulation of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le

brouillage radioélectrique publié par le ministère des Communications du Canada.

Normas Oficiales Mexicanas (NOM)

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el

aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben

ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina de

baño, lavabo, sótano mojado o cerca de una alberca, etc.

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean

recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea recomendado

por el fabricante.

Hardened VDSL Ethernet Extender

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo

descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a

personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La

colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede

bloquea la ventilación, no se debe colocar en libreros o gabinetes que impidan el flujo de

aire por los orificios de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como

radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores) que

producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en

el instructivo de operación, o como se indique en el aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo

no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni

pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los

contactos y receptáculos donde salen del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del

fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un

largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre

la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

Hardened VDSL Ethernet Extender

Preface

This manual describes how to install and use the Hardened VDSL Ethernet Extender.

The Hardened VDSL Ethernet Extender introduced here provides one channel for

Ethernet over VDSL.

The Hardened VDSL Ethernet Extender fully complies with IEEE802.3 10Base-T and

IEEE802.3u 100Base-TX/FX standards.

In this manual, you will find:

yProduct overview

yFEATURES ON THE HARDENED VDSL ETHERNET EXTENDER

yIllustrative LED functions

yInstallation instructions

ySpecifications

Hardened VDSL Ethernet Extender

Table of Contents

Preface 4

Table of Contents5

Introduction 6

Product Overview 6

Product Features 6

Packing List 6

One-Channel Hardened VDSL Ethernet Extender 8

Ports8

VDSL Mode Settings8

DIP switch8

Front Panel & LEDs 9

Installation 10

Selecting a Site for the Equipment 10

DIN Rail Mounting 10

Connecting to Power 11

Specifications12

Hardened VDSL Ethernet Extender

Introduction

The Hardened VDSL Ethernet Extender provides one channel for Ethernet over VDSL.

This Hardened VDSL Ethernet Extender solution is perfectly fitted in the industrial

applications or rugged environment.

Product Overview

Product Features

yMeets NEMA TS1/TS2 Environmental requirements such as temperature, shock,

and vibration for traffic control equipment

yMeets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment

yOperates transparent to higher layer protocols such as TCP/IP

yEthernet Port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,

full/half-duplex; Auto MDI/MDIX

yVDSL port: Symmetrical on the VDSL, high-speed full-duplex 50Mbps

communications link over existing copper telephone line

yOne DIP switch for configuring Local (Loc) and Remote (Rmt)

yTen speeds with speed indicator LEDs on front panel of unit, up to 50Mbps @

about 300meters (984ft.), down to 1Mbps @ about 1,900meters (6,233ft.)

yOperating voltage and Max. current consumption: 0.225A @ 12VDC, 0.113A @

24VDC. Power consumption: 2.7W Max.

yPower Supply: Redundant 12-30VDC Terminal Block power inputs and 12VDC

DC JACK with 100-240VAC external power supply

yOperating temperature ranges from -34 to 74

ySupports Din-Rail, Panel, or Rack Mounting installation

Packing List

When you unpack this product package, you will find the items listed below. Please

inspect the contents, and report any apparent damage or missing items immediately to

our authorized reseller.

Hardened VDSL Ethernet Extender

The Hardened VDSL Ethernet Extender

USER’S MANUAL

AC to DC Power Adaptor and Power Cable (optional)

Hardened VDSL Ethernet Extender

One-Channel Hardened VDSL Ethernet Extender

Ports

The Hardened VDSL Ethernet Extender provides one TX port and one VDSL port.

For the TX port, it uses RJ-45 connector and auto senses the speed of 10/100Mbps.

For the VDSL port, it uses RJ-11 and Terminal Block connectors and auto senses the

speed of 1/3/5/10/15/20/25/30/40/50Mbps.

VDSL Mode Settings

VDSL mode settings are made very simple by means of a DIP (Dual Inline Package)

switch on the top panel of the Hardened VDSL Ethernet Extender.

DIP switch

There is one pin on the DIP switch for VDSL mode settings. Refer to the table below

for more details.

Loc Rmt

The device operates in local

mode

The device operates in remote

mode

Hardened VDSL Ethernet Extender

Front Panel & LEDs

LED Indicators

The LED indicators give you instant feedback on status of the Hardened VDSL

Ethernet Extender:

LEDs State Indication

Power1

Power2

Power3

Steady Power on

Off Power off

Ethernet

Link/ACT

Steady A valid Ethernet connection established

Flashing Transmitting or receiving Ethernet data

ACT stands for ACTIVITY

Off Neither valid Ethernet connection established nor

transmitting/receiving Ethernet data

FDX Steady Ethernet Connection in full-duplex mode

FDX stands for FULL-DUPLEX

Off Ethernet Connection in half-duplex mode

Ethernet over VDSL

1 Green The VDSL port transmitting/receiving at 1Mbps, up to 1900M

Amber The VDSL port transmitting/receiving at 3Mbps, up to 1800M

2 Green The VDSL port transmitting/receiving at 5Mbps, up to 1600M

Amber The VDSL port transmitting/receiving at 10Mbps, up to 1400M

3 Green The VDSL port transmitting/receiving at 15Mbps, up to 1200M

Amber The VDSL port transmitting/receiving at 20Mbps, up to 1000M

4 Green The VDSL port transmitting/receiving at 25Mbps, up to 800M

Amber The VDSL port transmitting/receiving at 30Mbps, up to 700M

5 Green The VDSL port transmitting/receiving at 40Mbps, up to 600M

Amber The VDSL port transmitting/receiving at 50Mbps, up to 300M

Remote Steady The device operates in remote mode

Local Steady The device operates in local mode

Error Steady Error occurred

Link Steady A valid VDSL connection established

Hardened VDSL Ethernet Extender

Installation

This chapter gives step-by-step installation instructions for the Hardened VDSL

Ethernet Extender.

Selecting a Site for the Equipment

As with any electric device, you should place the equipment where it will not be

subjected to extreme temperatures, humidity, or electromagnetic interference.

Specifically, the site you select should meet the following requirements:

•The ambient temperature should be between -34 to 74 degrees

Celsius.

•The relative humidity should be less than 95 percent, non-condensing.

•Surrounding electrical devices should not exceed the electromagnetic

field (RFC) standards.

•Make sure that the equipment receives adequate ventilation. Do not

block the ventilation holes of the equipment.

•The power outlet should be within 1.8 meters of the product.

DIN Rail Mounting

Fix the DIN rail attachment plate to the back panel of the Hardened VDSL Ethernet

Extender.

Installation: Place the Hardened VDSL Ethernet Extender on the DIN rail from above

using the slot. Push the front of the Hardened VDSL Ethernet Extender toward the

mounting surface until it audibly snaps into place.

Removal: Pull out the lower edge and then remove the Hardened VDSL Ethernet

Extender from the DIN rail.

Inhaltsverzeichnis

Andere Black Box Extender Handbücher

Black Box

Black Box SDSL Network Extender 2000 Bedienungsanleitung

Black Box

Black Box ACU7001A Bedienungsanleitung

Black Box

Black Box IC568A Bedienungsanleitung

Black Box

Black Box ACS4422A-R2 Bedienungsanleitung

Black Box

Black Box ServSwitch ACS253A-CT Bedienungsanleitung

Black Box

Black Box 4KDPKVMXT-100M-R2 Bedienungsanleitung

Black Box

Black Box ACU7017A Bedienungsanleitung

Black Box

Black Box LS900A Bedienungsanleitung

Black Box

Black Box IC280A-R2 Bedienungsanleitung

Black Box

Black Box USB Director RS-232 Bedienungsanleitung

Black Box

Black Box ServSwitch ACU5000A Bedienungsanleitung

Black Box

Black Box MTU9230 Bedienungsanleitung

Black Box

Black Box ServSwitch ACU5010A Bedienungsanleitung

Black Box

Black Box ACU1500A-R3 Bedienungsanleitung

Black Box

Black Box VX-HDMI-FO Bedienungsanleitung

Black Box

Black Box ServReach KVMCube Bedienungsanleitung

Black Box

Black Box EMD4000R Bedienungsanleitung

Black Box

Black Box LWE121A Bedienungsanleitung

Black Box

Black Box ACU1700A Bedienungsanleitung

Black Box

Black Box ACI-2000A Bedienungsanleitung

Black Box

Black Box LB200A Bedienungsanleitung

Black Box

Black Box LR0025A-KIT Bedienungsanleitung

Black Box

Black Box ACS1009A-xx Bedienungsanleitung

Black Box

Black Box IC443A Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung