Black Box MEG201AE Bedienungsanleitung

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

Manual

MEG201AE

VDSL2 Ethernet Extender Kit

VDSL2 Point to Point Solution

Consisting of 1xTransmitter and 1xReceiver

MEG201RAE

VDSL2 Receiver

Part of VDSL2 Point to Multipoint Solution

used with VDSL2 Switch MEG821AE

MEG201TAE

VDSL2 Transmitter

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

OVERVIEW

MEG201AE works as a transparent point to point Bridge for Ethernet and/or Telephony

connections using a Transmitter and a Receiver. When used with the VDSL2 switch

MEG821AE it is a Multipoint to Point solution. The MEG201AE uses new VDSL2

technology operating at different frequency bands with the feature to adapt its

performance to the characteristics of the copper medium used. The following cable

lengths and bandwidths are possible according to the band profile setup:

30a (Default band profile) 0-350m at 100Mbps down- and upstream

350-450m at 70-85/40Mbps downstream/upstream

450-600m at 40-60/10Mbps downstream/upstream

600-900m at 20-40/1-5Mbps downstream/upstream

Using Band profile 30a for distances

beyond 900m is not recommended

8d (Alternative band profile) 0-800m at 60-80/15 Mbps downstream/upstream

800-1200m at 30-50/5-10 Mbps downstream/upstream

1200-1500m at 30/2-5 Mbps downstream/upstream

Using Band profile 8a for distances

beyond 1500m is not recommended

Downstream: Traffic from Transmitter to Receiver

Upstream: Traffic from Receiver to Transmitter

For distances higher than those mentioned above, the MEG201AE is not the

recommended product. Other Black Box xDSL products should then be your

choice. Check MDS93x, MDS95x, MDE5xxx or MEG101 series products to get

distances of many many kilometers

These distances may and will vary depending on the quality of your wires. Keep in mind

that every intermediate connection of the cable will possibly increase losses and result in

less reach and/or bandwidth. Avoid cables that are not truly isolated, that may get wet or

are old and corroded. Running high power current nearby is also not recommended due

to the possibility of induced interference.

Avoid using telephony RJ11 ribbon cables. These cables are built with using very

low diameter stranded cables. Using them will mean that bandwidth is lower and

reach is shorter!

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

The front-panel provides LED indication of system and interface status. The in-built

POTS splitter allows a standard POTS phone to be connected at the Receiver. Full or

half duplex mode LAN operation is automatically sensed and configured. The

MEG201AE features an integrated 4 Port 10/100 Switch. Because of the switch please

consider that some non standard Ethernet Frames will not pass MEG201AE.

MEG201AE is configured by Web management. The serial port is intended to be used

by support staff with technical skills only. The standard IP addresses of the MEG201AE

set up are:

Transmitter MEG201TAE 192.168.16.249

Receiver MEG201RAE 192.168.16.250

Use the Webbrowser of your choice (older versions of Netscape or IE may not be able to

show you all options) to address MEG201AE. The default password is admin

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

The Modem

From Left To Right

1 Just a hole where in previous versions a RESET button was

2 4x10/100 LAN Ports

3 VDSL Link Port, middle Pins active (RJ11)

4 Phone POTS ab Port, middle Pins active (RJ11)

Transmitter side intended to use with a PBX (FXO)

Receiver side intended to use with a telephone or telefax (FXS)

5 Serial RS232 Port for use by authorized personnel only

6 Power Input (12VDC, max.1A)

From Left To Right

PWR Power LED

E1-E4 Link LED for the Ethernet Switch Ports

Blinking while ongoing Activity

LINK Link LED for the VDSL Port

Blinking while other side found and connection is being established

Steady On while VDSL Link valid

Note: Pictures in the manual mainly show the modem in white. Thanks to the features of digital photography.

Of course MEG201AE is black and is only available in black.

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

INSTALLATION

For most applications you just need to connect the Transmitter and Receiver and power

them up (Picture shows Transmitter on the Left, Receiver on the Right)

Since the Receiver and Transmitter have their own IP addresses please check that the

addresses 192.168.16.249 and 192.168.16.250 are not in use by any other of your

network equipment. Initially, it may be useful for you to just connect Transmitter and

Receiver to the VDSL Line without connecting any other network equipment.

When using the VDSL2 switch (MEG821AE) please do not forget that all Receivers have

the same default IP address. It is recommended to change the IP address of each

receiver on its own before connecting to the switch.

For wire lengths within the distance limits previously mentioned (<900m), the system will

automatically establish the Link and set itself up. The MEG201AE is built using a

switching chipset and so some special Ethernet Frames will not pass across the VDSL

Link. Standard TCP und UDP traffic will pass to the other side transparently. The

MEG201AE is optimised for TCP traffic. If you use UDP traffic for Video Transmission

with high Frame sizes you will experience non optimal results.

After the Link between the Transmitter and Receiver has been established successfully

the WAN/LINK LED will be in a steady on state. At this point you should set up

appropriate IP addresses for the Transmitter and Receiver. You do this by either using a

PC within the subnet of the default IP addresses (192.168.16.x) or by setting a

temporary IP address by RS232 connection. See the next chapters for more information.

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

CONFIGURING BY WEB

The MEG201AE can be configured by using a Web browser. The modems have default

IP addresses and to use the Web Configuration method you need a PC within the same

subnet as the default IP addresses of MEG201AE.

MEG201AE Transmitter 192.168.16.249

MEG201AE Receiver 192.168.16.250

You can for example set your PC up with IP address 192.168.16.1. Please consult the

manual of your operating system on how to do this. If you can not change the IP address

of your PC then choose the alternative method to configure the IP address of

MEG201AE by RS232 serial (see below).

By entering the IP address as the URL into your browser you can get access. A window

will appear asking you for login. The default password is admin.

(Transmitter on Left, Receiver on Right)

The Screen you will see looks very similar for both the Transmitter and Receiver. Click

on Advanced Setup to configure the modem. The next screen will show you:

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

As you can see the Receiver offers you more options to configure. This is because you

can use the Receiver as an ADSL2+ Modem to be used with your incoming Internet

Service Provider Line as well as a point to point solution. Since the purpose of this

manual is to describe setup for your VDSL2 link please leave the options for

WAN/NAT/Firewall/Route and uPnP unchanged!

SYSTEM

Administator Settings (Transmitter and Receiver)

Allows you to change the default password

Firmware Upgrade (Transmitter and Receiver)

Allows you to upgrade the firmware

Device Mode (Receiver only)

Allows you to change the Receiver from VDSL2 Extender Set to ADSL2+ Router. Leave

setting to Switch Mode for normal operation

(Switch Mode in Factory Default)

System Status

Information about the Device

Reboot

Lets you reboot the Device while leaving the settings unchanged

Reset System

Lets you reboot the Device while setting everything back to factory default

LAN

LAN Settings

Lets you configure IP Address and enable or disable the DHCP Server

(Disabled in Factory Default)

DHCP Client List

Lets you view the IP Addresses given to network devices by the DHCP Server

LAN Switch Port Setting

Lets you configure which Speed and Duplex Mode ALL 4 SWITCH PORTS do.

(Auto 10/100 Full/Half in Factory Default)

LAN Port Status

Lets you view the status of the four Switch Ports.

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

VDSL2

Channel Config

Lets you control the bandwidth passing across the Link.

(Factory Default is 64 kbps Minimum and 102400 kbps Maximum)

Also gives you the chance to set up Interleave. Higher Interleave values may give you a

more consistent latency.

(Factory Default is 1ms)

Line Config

Lets you configure the target SNR value for your Link that is acceptable. By lowering

that value you may get a link at a higher reach, but it will not be stable.

(Factory Default is 6 db)

Profile Config

Lets you configure the profile being used for your Link.

You can choose Profile, Band Plan, Filter and Tone Mode for the Transmitter.

You can choose Filter and Tone Mode for the Receiver.

Filter and Tone Mode of Transmitter and Receiver need to match.

(Factory Default for Filter is Off, for Tone Mode is V43)

The choosen Profile and Band Plan of the Transmitter are automatically

detected by the Receiver

The Profile and Band Plan tell the Modems which frequencies are being used and how

data is processed and transferred. The Filter and Tone Mode tells the modem

specialities about the line.

Optimal Setups:

Profile 30a, Annex C_8K, Filter Off and Tone Mode V43 for High Bandwidth

Profile 8d, Annex A M1_EU32, Filter Off and Tone Mode B43 for Long Distance

Bands Config

Let you configure special frequencies to be used.

Do not make any changes unless specifically advised by Black Box!

LoopBack

Enable LoopBack Functions for Testing

Users are not intended to use this function !

Activate Deactivate

Activate or Deactivate the Link

The Link needs to be activated on both sides to operate

LineStatus

For every Frequency section you can view the SNR values.

They should be positive and the higher, the better.

ChannelStatus

The Link performance

VersionInfo

Detailed Information about the software and hardware of MEG201AE

SNRGraph

Graphics showing you SNR values

BitsGraph

Graphics showing you where how much data is transferred.

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

CONFIGURING BY RS232

MEG201AE features a Serial RS232 Port. Use a straight through (1:1) cable to configure

the MEG201AE using Hyperterminal or any VT100 application of your choice.

You need to setup a bitrate of 115200bps with 8N1 without any handshaking.

If the MEG201AE has been powered up already you will see a prompt by hitting the

ENTER key:

/ #

If you have not powered up MEG201AE, please do so and wait until the boot process is

finished. The boot process finishes with the following (for the Transmitter, the Receiver

looks very similar):

MEG201AE VDSL Transmitter

Image V 2.0.12 (CO)

FW: v9.7.3.11.0.2

DSL-API: v2.0.12

DFE-Drv: v0.1.4.8

WEB-Interface: vD.2x

--------------------------------------------------------------

Addr: 1200007c, value: bfffffff

BusyBox v1.00 (2006.05.29-14:43+0000) Built-in shell (ash)

Enter 'help' for a list of built-in commands.

/ #

As you may identify from the commands above MEG201AE is a Linux based device.

Many of the common Linux commands can be used here. However, please consider that

you purchased a VDSL2 modem device, not a PC. And always keep in mind that Black

Box gives you support for configuring a standard VDSL2 modem. If you try to use the

MEG201AE as a Linux hardware platform and modify its internal software structure

there is no support or warranty on the unit.

Manual of VDSL2 Solution

http://www.black-box.eu

_____________________________________________________________________________

You can use the Serial Interface to configure an IP address by this command:

ifconfig adm0 <ipadress> netmask <subnetmask>

(Example: ifconfig adm0 192.168.16.240 netmask 255.255.255.0)

This configuration is activated immediately but is only temporary because not stored in

flash memory. We recommend you continue configuring by Web method.

Other commands very useful:

rawaccess –e (Factory Default)

reboot (RESET)

ping (check connectivity to an IP address)

The Serial Bootmenu

Sometimes it may be necessary to use the Serial Bootmenu. Please check with Black

Box Tech Support before you attempting to do so.

While powering up the MEG201AE you can stop the boot process while this message is

displayed. Press SPACE three times to enter the boot menu then:

Press <space> key tree times to enter boot menu..

Loader Menu

==================================

[1] Xmodem Download

[2] TFTP Client Download

[3] Print Boot Params

[4] Set Boot Params

[5] Update bootloader

[6] Exit

Please enter your number:

Option 1 enables you to upgrade the firmware by RS232 with Xmodem. This is a very

slow but very secure upgrade method.

Option 2 enables you to upgrade the firmware by TFTP.

Option 3 will give you information about the device

Option 4 enables you to change CO/CPE status

Option 5 enables you to upgrade the bootloader

It is not recommended to use any of these options without consulting Black Box or

unless specifically instructed by Black Box tech support to do so.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Extender Handbücher

Black Box

Black Box ME890A-R2 Bedienungsanleitung

Black Box

Black Box ACX300-R2 Bedienungsanleitung

Black Box

Black Box LBPS01A-KIT Bedienungsanleitung

Black Box

Black Box ACU5800A Wizard DP Montageanleitung

Black Box

Black Box ServSwitch ACU075A-PS2 Bedienungsanleitung

Black Box

Black Box IC502A-R2 Bedienungsanleitung

Black Box

Black Box AC1070A Bedienungsanleitung

Black Box

Black Box ServSwitch ACS253A-CT Bedienungsanleitung

Black Box

Black Box AVS-HDB-TX Bedienungsanleitung

Black Box

Black Box ServSwitch ACU5200A Bedienungsanleitung

Black Box

Black Box Ultra 2 Bedienungsanleitung

Black Box

Black Box LR0304A-KIT Bedienungsanleitung

Black Box

Black Box AVS-HDB-4TX Bedienungsanleitung

Black Box

Black Box ACU7017A Bedienungsanleitung

Black Box

Black Box ACI-2000A Bedienungsanleitung

Black Box

Black Box LB323A Bedienungsanleitung

Black Box

Black Box IC280A-R2 Bedienungsanleitung

Black Box

Black Box AC1080A Bedienungsanleitung

Black Box

Black Box ServSwitch ACU1004A Bedienungsanleitung

Black Box

Black Box Sync SHM-NPR MP Bedienungsanleitung

Black Box

Black Box EMD4000R Bedienungsanleitung

Black Box

Black Box ServSwitch ACU1022A Bedienungsanleitung

Black Box

Black Box ServSwitch ACU5002A Bedienungsanleitung

Black Box

Black Box ACS2001A-R3 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung