Black Box Emerald EMD4000T Bedienungsanleitung
STEP X - Name of Step
24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM
EMD4000T, EMD4000R
EMERALD
KVM 4K
QUICK START GUIDE
STEP 1A - Transmitter Diagrams
1
2 3 6
5
487 79
Front panel
Back panel
STEP 1B - Transmitter Components
TABLE 1. EMD4000T COMPONENTS
NUMBER IN DIAGRAM AT LEFT DESCRIPTION DESCRIPTION
1 Power LED LED indicates power status
2 12-VDC, 3-A Power In connector Connect to supplied power adapter
3DB9 connector Connects to serial console port
4 USB Type B connector Connect to PC/workstation USB
connector
5 RJ-45 connector Connects to LAN
6DisplayPort 1.2 video connector Connect to PC Video
7 (2) SFP+ ports Dual 10G network ports
8Audio Line In Connect to PC Line Out
9 Audio Line Out Connect to PC Line In
STEP 2A - Receiver Diagrams
1234
6
510
9
8
710
Front panel
Back panel
STEP 2B - Receiver Components
TABLE 2. EMD4000R COMPONENTS
NUMBER IN DIAGRAM AT LEFT DESCRIPTION DESCRIPTION
1On/Off button Powers on and off unit. LED
indicates power status.
2 Audio LIne Out Connects to speakers
3 Audio Microphone In Connects to microphone
4 (2) USB Type A connectors Connect to USB peripherals
5 12-VDC, 3-A Power In connector Connect to supplied power adapter
6DB9 connector Connects to serial console port
7 (2) USB Type A connectors Connect to USB peripherals
8 RJ-45 port Connect to network
9DisplayPort 1.2 Video connector Connect to monitor
10 (2) SFP+ connectors Dual 10G network ports
STEP 3 - Connect Power
CONNECT POWER TO TRANSMITTER
1. Locate the power supply adapter and the AC
line cord.
2. Plug the DC connector of the power supply
into the matching socket on the rear of the
transmitter.
3. Attach the AC line cord to the power supply
adapter.
CONNECT POWER TO RECEIVER
1. Locate the power supply adapter and the AC
line cord.
2. Plug the DC connector of the power supply
into the matching socket on the rear of the
receiver.
3. Attach the AC line cord to the power supply
adapter.
STEP 4 - Connect the Peripherals
CONNECT THE TRANSMITTER
1. Attach the Emerald Transmitter to the target
PC/workstation using DisplayPort and USB
Type B cables.
2. Connect the SFP+ transceiver appropriate
for the cable type and distance you are running
over the fiber to the SFP+1.
3. Connect from this transceiver to your
10G network switch or directly to a receiver.
Emerald does support direct attach SFP+,
typically this will be the most cost efficient
option for a relatively short distance (less than
22.9 feet [7 meters]).
NOTE: SFP+1 must be used as the primary
network connection on the Emerald 4K
Transmitters.
CONNECT THE RECEIVER
1. Attach the monitor, keyboard, mouse, USB
and audio devices to the Emerald Receiver.
2. Connect the SFP+ transceiver appropriate
for the fiber cable type and distance you are
running over fiber to SFP+1.
3. Connect from this transceiver to your 10G
network switch or directly to the receiver.
NOTE: SFP+1 must be used as the primary
network connection on the Emerald 4K
Receivers.
STEP 5 - Starting Up and Default Settings for IP
STARTING UP
1. Once everything is connected, press the
Power button on the front of the Emerald
Receiver.
2. The On-Screen Display (OSD) will appear on
the screen.
3. Enter the default administrator user name
and password.
4. The default network setting for the Emerald
Receiver uses a preconfigured static IP
address.
DE FAULT SETTINGS
Default Settings:
Transmitter IP Address: 192.168.1.22
Receiver IP Address: 192.168.1.21
Type: Static
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
Admin username: admin
Admin password: no password, it is blank by
default
Ports Used: 3389
IMPORTANT: Do not lose the admin password
once configured; there is no way to reset or
retrieve it. The Emerald receiver has the option
to create a second administrator account as a
backup.
STEP 6 - Point-to-Point Installation for IP
POINT-TO-POINT INSTALLATION
In a point-to-point configuration, no
administrator setup of the Emerald
Transmitter or the Emerald receiver is
required. This enables you to install the
system quickly, directly out of the box. In the
point-to-point configuration, you can install
only one transmitter and receiver pair on a
subnet and both must be on the same subnet
unless a router is present in the network
to span subnets. To span across different
subnets, you will need to have admin rights to
both routers on either side of the installation
and setup port forwarding for Port 9020, 9030
and 3389 for KVM; Port 3389 for RDP for
Remote Desktop.
STEP 7 - Matrix Installation and Getting Started for IP
MATRIX INSTALLATION
In an IP installation, every Emerald transmitter
and receiver requires its own IP address.
The network setting is set to static, so the
addresses will need to be configured manually:
1. Always configure the transmitter first by
connecting the transmitter to the receiver, then
connect a keyboard, monitor, and mouse to the
receiver unit (receiver is on at this time).
2. Once the transmitter is configured, you can
now configure the receiver.
3. A transmitter out of the box must be
configured on the same subnet.
GETTING STARTED
Once the IP addresses have been configured,
each receiver will need to be configured for
users, user passwords, user access rights
and default video resolutions. You can access
these settings from the receiver’s OSD (reboot
the receiver and login as admin) and begin
configuring these parameters.
NOTE: Each receiver can support a maximum
of 32 users and a maximum of 32 targets
(virtualized or transmitter).
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Black Box Matrix-Umschalter Handbücher
Black Box
Black Box Boxilla Bedienungsanleitung
Black Box
Black Box AVS-3200-R2 Bedienungsanleitung
Black Box
Black Box VSDDVI Series Bedienungsanleitung
Black Box
Black Box SW540A-R3 Bedienungsanleitung
Black Box
Black Box VSW-HDMI2X2-4K Bedienungsanleitung
Black Box
Black Box AC1051A Bedienungsanleitung
Black Box
Black Box IS290A Bedienungsanleitung
Black Box
Black Box AC1120A Bedienungsanleitung
Black Box
Black Box VSW-DVI8x8 Bedienungsanleitung
Black Box
Black Box ACX048 Bedienungsanleitung
Black Box
Black Box ServSwitch DKM FX Bedienungsanleitung
Black Box
Black Box VSW-HDMI4X4-B Bedienungsanleitung
Black Box
Black Box AVS-HDMI2-4X4 Bedienungsanleitung
Black Box
Black Box DCX1000 Bedienungsanleitung
Black Box
Black Box AVS800 Bedienungsanleitung
Black Box
Black Box AVS-1600-R2 Bedienungsanleitung
Black Box
Black Box AVS1600 Bedienungsanleitung
Black Box
Black Box AC180A Bedienungsanleitung
Black Box
Black Box AVS-HDMI2-8X8-R2 Bedienungsanleitung
Black Box
Black Box EMERALD SE DUAL-HEAD Bedienungsanleitung
