Black Box IC832A Bedienungsanleitung

IC832A & IC833A - 1008 page 1/x p/n 8024 Rev 001

Black Box Corporation - 1000 Park Drive - Lawrence, PA 15055-1018

Tech Support and Ordering: 724-746-5500 - Fax: 724-746-0746

To contact us about Black Box products or services: [email protected]

Specifications

Serial Technology

RS-485 2-Wire Data A(-), Data B(+), Ground

RS-485 4-Wire TDA(-), TDB(+), RDA(-), RDB(+), Ground

Connector Removable Terminal Block (28 to 16 AWG)

Data Rate Up to 460.8 Kbps

USB Technology

Connector USB Type B Female (High Retention)

Standard 2.0 (Backward Compatible)

Data Rate 12 Mbps Power

Source USB Port

Input Voltage 5 VDC

Consumption ~ 0.5 W (Low power device, draws less than

100 mA) Software

Driver CD Windows 98, ME, 2000, XP, Vista

Mechanical

Dimensions 2.6 x 1.3 x .6 in (6.5 x 3.2 x 1.6 cm)

Enclosure In-line mounted, plastic

Weight 0.23 lbs (104.3 g) with USB Cable

Environmental

Operating Temp 32 to 158°F (0 to70 °C)

Storage Temp -40 to 185 °F (-40 to 85 °C)

Op Humidity 0 to 95 % (Non-condensing)

MTBF 1869313 hours

MTBF Method Parts Count Reliability Prediction

Regulatory

Approvals FCC, CE

Ordering Information

IC832A USB to RS-485 Mini-Converter

IC833A USB to RS-485 Mini-Converter

IC832

& IC833

USB to RS-485 Mini-Converter

9Connect RS-485 Devices to your USB Port

9Perfect for Field Service Applications

9Small – Fits easily into any laptop bag

9USB Port Powered

9USB 2.0 (12 Mbps) Compatible

9RS-485 Data rates up to 921.6 Kbps

9Removable Terminal Block for Easy Wiring

9High Retention USB Connector

9Supports Windows 98, ME, 2000, XP, & Vista

Universal Serial Bus (USB) has become the

connectivity workhorse of today’s PCs, replacing the

familiar serial ports. However, many commercial

and industrial devices still use the RS-485 interface.

To connect these devices to modern PCs, you need

a simple and reliable conversion solution. The

IC832A and IC833A offer this solution in a space

saving, USB Port powered package. Simply plug

the converter into an available USB port on your

computer or USB hub and install the drivers

supplied on CD ROM. The device will show up as

an additional COM port in the Windows Device

Manager which is fully compatible with your

Windows applications. A one meter USB cable is

included. 

IC832A & IC833A - 1008 page 2/x p/n 8024 Rev 001

Black Box Corporation - 1000 Park Drive - Lawrence, PA 15055-1018

Tech Support and Ordering: 724-746-5500 - Fax: 724-746-0746

To contact us about Black Box products or services: [email protected]

Package Contents

•IC832A or IC833A USB to RS-485 Mini-Converter

•3ft (1m) USB Cable

•Datasheet

•CD with Drivers for Windows 98, ME, 2000, XP and

Vista



Terminal Block

IC832A

Position Signal

A(-) Data A (-)

B(+) Data B (+)

A(-) Data A (-)

B(+) Data B (+)

GND Ground IC833A

TDA(-) Transmit Data A (-)

TDB(+) Transmit Data B (+)

RDA(-) Receive Data A (-)

RDB(+) Receive Data B (+)

GND Ground

Driver Installation

Screen shots are from Windows XP

THE FOUND NEW HARDWARE WIZARD WILL

RUN TWICE. ONCE TO INSTALL THE USB

DEVICE AND ONCE TO INSTALL THE SERIAL

COM PORT.

•Connect the converter to your PCs USB port with

the supplied cable.

•The Found New Hardware wizard will start.

•When prompted to connect to Windows Update

to search for the driver, select “No, not at this

time” and click on Next >

•

Select Install the software automatically and click

Next>

•

A warning concerning Windows logo testing will

be displayed. Click on Continue Anyway >

•

The Completing the Found New Hardware Wizard

will be displayed. Click on Finish >

THE FOUND NEW HARDWARE WIZARD WILL

RUN TWICE. ONCE TO INSTALL THE USB

DEVICE AND ONCE TO INSTALL THE SERIAL

COM PORT.

IC832A & IC833A - 1008 page 3/x p/n 8024 Rev 001

Black Box Corporation - 1000 Park Drive - Lawrence, PA 15055-1018

Tech Support and Ordering: 724-746-5500 - Fax: 724-746-0746

To contact us about Black Box products or services: [email protected]

Check Drivers

Screen shots are from Windows XP

•Right click on My Computer. Select the Hardware

tab.

•Expand the USB Controllers tree. The USB Serial

Converter will be listed.

•Expand the Ports (COM & LPT) tree. The USB

Serial Port will be listed as the next available

COM Port.

Installation Notes

•

When the driver is installed, the converter is associated

to that PC. If you plug in a different converter, the driver

must be installed again. Another COM port will also be

created with the driver installation.

•Instructions for uninstalling the driver are located on the

CD ROM.

IC832A Wiring

•

This converter is used for RS-485 2-Wire Systems.

•Loosen the screws to open the Terminal Block lead

clamps for the A(-), B(+), and GND terminals.

•Insert the RS-485 2-Wire signal leads in accordance

with the diagram above. The TB will accept 28 to 16

AWG wire.

•Tighten the screws to close the TB lead clamps. Ensure

the clamps hold the leads securely. However, do not

over tighten.

•Bias is provided by 4.7KΩpull-up and pull-down

resistors.

•If termination is required, it must be installed externally.

In most cases, termination is not required.

•During operation, the receiver toggles with the transmit

data.

IC832A & IC833A - 1008 page 4/x p/n 8024 Rev 001

Black Box Corporation - 1000 Park Drive - Lawrence, PA 15055-1018

Tech Support and Ordering: 724-746-5500 - Fax: 724-746-0746

To contact us about Black Box products or services: [email protected]



485USBTB-4W Wiring IC832A Loop Back Test

IC832A Back to Back

Test

•

Loopback TDA(-) to RDA(-) and TDB(+) to

RDB(+) as shown in the diagram above.

•Using Hyper Terminal or similar program,

connect to the appropriate COM port. Set the

desired baud rate. Ensure Hyper Terminal local

echo is OFF.

•Transmit data. If the same character string is

returned, the test is good.

•This converter is used for RS-485 4-Wire Systems.

•Loosen the screws to open the Terminal Block lead

clamps for the TDA(-), TDB(+), RDA(-), RDB(+), and

GND terminals.

•Insert the RS-485 2-Wire signal leads in accordance

with the diagram above. The TB will accept 28 to 16

AWG wire.

•Tighten the screws to close the TB lead clamps. Ensure

the clamps hold the leads securely. However, do not

over tighten.

•Bias is provided by 4.7KΩpull-up and pull-down

resistors.

•If termination is required, it must be installed externally.

In most cases, termination is not required.

•During operation, the receiver is always active.

•

Due to the circuit configuration, a loop back test

is not possible with this model. However, two

converters can be used in a back to back

configuration.

•Wire the converters as shown above.

•Using Hyper Terminal or similar program,

connect to the appropriate COM ports. Set the

desired baud rate.

•Transmit data. If the same string is received on

the distant end, the test is good.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Box Medienkonverter Handbücher

Black Box

Black Box 232<->488 Converter IC026A-R3 Bedienungsanleitung

Black Box

Black Box MCX S9 Series Gebrauchsanweisung

Black Box

Black Box IC456A-R5 Bedienungsanleitung

Black Box

Black Box LE2122A-R4 Bedienungsanleitung

Black Box

Black Box AC1056A-2 Bedienungsanleitung

Black Box

Black Box IC700A Bedienungsanleitung

Black Box

Black Box VSC-HDMI-SDI Bedienungsanleitung

Black Box

Black Box AC425A Bedienungsanleitung

Black Box

Black Box IC199A-R3 Bedienungsanleitung

Black Box

Black Box LGC5150A Bedienungsanleitung

Black Box

Black Box AC217A Bedienungsanleitung

Black Box

Black Box IC830A Bedienungsanleitung

Black Box

Black Box PI125A-R2 Bedienungsanleitung

Black Box

Black Box LGC1713A-SX Bedienungsanleitung

Black Box

Black Box ServSensor JR EME102A Bedienungsanleitung

Black Box

Black Box LE1500-BNC Bedienungsanleitung

Black Box

Black Box IC940A-F Bedienungsanleitung

Black Box

Black Box LE1510A-R2 Bedienungsanleitung

Black Box

Black Box AC138A Bedienungsanleitung

Black Box

Black Box ICD114A Bedienungsanleitung

Black Box

Black Box ServSwitch ACL8500A Bedienungsanleitung

Black Box

Black Box LPD401A Bedienungsanleitung

Black Box

Black Box LE2120A-R4 Bedienungsanleitung

Black Box

Black Box HP Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung