BLACK DECKER BW13 Bedienungsanleitung
BW13
BW16
BW14, BW15
BW17
English
简体中文
한국어
07
14
20
ภาษาไทย
BAHASA INDONESIA
TIẾNG VIỆT
26
32
39
High Pressure Washer | 高压清洗机 | 고압 세척기 |
| Mesin Pencuci Bertekanan |
Máy phun rửa áp lực
WARNING: READ INSTRUCTIONS MANUAL BEFORE USING PRODUCT.
警告！未经阅读本说明书请勿使用本器具。
경고: 제품을 사용하기 전에 사용 설명서를 읽으십시오.
PERINGATAN: BACA PANDUAN PENGGUNAAN SEBELUM MENGGUNAKAN PRODUK.
CẢNH BÁO: VUI LÒNG ĐỌC KỸ HƯỚNG DẪN NÀY TRƯỚC KHI SỬ DỤNG SẢN PHẨM
13
13
13
13
14
14
8
8
16 15
17 18
12
2121 21 21
21
12 12 12
219
20
20
2
1
1
34
9
10
11
5
7
6
BW13
BW13,
BW14,
BW15
BW16,
BW17
BW14,
BW15 BW16 BW17
8 8 8 8
14
FIG. A / 图 A / 그림 A / A / GBR. A / HÌNH A
fFor house hold use only
f仅供居家使用
f하우스홀드전용
f
fHanya untuk digunakan di rumah
fChỉ dành cho các thiết bị gia dụng
34
1 2 2
3 3
5 6 6
Ø13
OK! KO!
8
8
15
3
3
3
33
6
OK!
814
13
13
14 8
11 x 2
11x 2
11x 2
11x 2
BW14,
BW15
BW16,
BW17
BW13
BW17
BW13, BW14,
BW15 BW16,
BW17
BW14, BW15,
BW16
BW16,
BW17
KO!
6
22
FIG. B / 图 B / 그림 B / B / GBR. B / HÌNH B
87 7
Nr.
1 2 4
5 6
0I
3
1
22
4
4
11
55
12
1
BW13, BW14,
BW15
BW13, BW14,
BW15
BW16,
BW17
BW16,
BW17
4
21
19
19
19
19
20
20
19
20
20
9
2
BW13,
BW14,
BW15
BW16,
BW17
BW16,
BW17
BW13,
BW14,
BW15
BW13, BW14,
BW15 BW16, BW17
BW13 BW14, BW15,
BW16, BW17
7
6
10 10
4 5
BW13,
BW14,
BW15,
BW16
BW13,
BW14,
BW15
BW16,
BW17
BW17
FIG. E / 图 E / 그림 E / E / GBR. E / HÌNH E
FIG. F / 图 F / 그림 F / F / GBR. F / HÌNH F
Note: The diagrams are for reference, the product may change in appearance or specifications without notice.
注：图表仅供参考。产品的外观或规格可能会出现变动。恕不另行通知。
참고:다이어그램은참조용이며제품의외관이나사양이예고없이변경될수있습니다.
Perhatian: Diagram ini hanya untuk referensi, penampilan atau spesifikasi produk dapat berubah tanpa pemberitahuan.
Lưu ý: Hình vẽ chỉ mang tính tham khảo, hình dáng và thông số sản phẩm có thể thay đổi
mà không có thông báo trước.
ENGLISH • 7
SAVE THESE INSTRUCTIONS
The appliance you have purchased is a technologically
advanced product designed by one of the leading
manufacturers of high pressure pumps. To obtain the best
performance from your unit, read this booklet carefully and
follow the instructions each time you use it. We congratulate
you on your choice and wish you successful operation.
GENERAL SAFETY RULES
SAFETY INSTRUCTIONS
General power tool safety warnings.
Warning! Read all safety warnings and
all instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term in all of the warnings listed below refers to your
mains operated (corded) power tool or battery operated
(cordless) power tool.
1. Safety “Must Nots”
a. Explosion or poisoning hazard. Do not use the
appliance with inammable or toxic liquids, or any
products which are not compatible with the correct
operation of the appliance.
b. Injury hazard.Do not direct the water jet towards
people or animals.
c. Electric shock hazard. Do not direct the water jet
towards the unit itself, electrical parts or towards other
electrical equipment
d. Short circuit hazard. Do not use the appliance
outdoors in case of rain.
e. Injury hazard. This machine is not intended for use
by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge. Children should be supervised to
ensure that they do not play with the appliance.
f. Electric shock hazard. Do not touch the plug and/or
socket with wet hands.
g. Electric shock and short circuit hazard. Do not use
the appliance if the electrical cable is damaged.
h. Explosion hazard. Do not use the appliance if the
high pressure hose is damaged.
i. Accident hazard. Do not jam the trigger in the
operating position.
j. Accident hazard. Check that the data plates are
axed to the appliance, if not, inform your dealer.
Units without plates must not be used as they are
unidentiable and potentially dangerous.
k. Explosion hazard. Do not tamper with or alter the
calibration of the safety valve.
l. Hazardous alteration of operating performance.
Do not alter the original diameter of the spray
head nozzle.
m. Accident hazard. Do not leave the appliance
unattended.
n. Short circuit hazard. Do not move the appliance
by pulling on the electrical cable.
o. Make sure that cars do not drive over the high pressure
hose.
2. Safety “Musts”
a. Short circuit hazard. All electrical conductors must
be protected against the water jet.
b. Electric shock hazard. The appliance must only be
connected to an adequate power supply in compliance
with all applicable regulations.
fUse of a safety residual current circuit-breaker
(R.C.C.B.) will provide additional protection
for the operator (30mA).
c. Injury hazard. The high pressure may cause
materials to bounce of surfaces at speed; therefore
protective clothing and safety goggles, safety boots,
safety gloves, safety helmets with visors, hearing
protection must be worn.
d. Accidental start-up hazard. Before doing work on
the appliance, remove the plug.
e. Injury hazard. Before pressing the trigger, grip the
gun firmly to counteract the recoil.
f. Contamination hazard. Comply with the requirements
of the local water supply company. According to DIN
1988, the appliance may only be connected to the
mains drinking water supply if a backow preventer
valve with drain facility is installed in the supply hose.
Water that has flowed through backflow preventers
is considered to be non-potable.
g. Accident hazard. Maintenance and/or repair of
electrical components must be carried out by qualified
and Authorized BLACK+DECKER staff for the warranty
to take effect. If the supply cord is damaged, it must
be replaced by the manufacturer, an Authorized
BLACK+DECKER service centre or an equally qualified
person in order to avoid a hazard. If the supply cord
is replaced by an equally qualified person, but not
Authorized by BLACK+DECKER, the warranty will
lose effect.
h. Injury hazard. Discharge residual pressure before
disconnecting the unit hose.
i. Accident hazard. Before using the appliance, check
every time that the screws are fully tightened and that
there are no broken or worn parts.
j. Explosion and electric shock hazard. Only use
detergents which will not corrode the coating
materials of the high pressure hose/electrical cable.
8 • ENGLISH
k. Injury hazard. Ensure that all people or animals keep
a minimum distance of 16yd. (15M) away.
3. Improper use
fUse by unskilled persons or those who have not read
and understood the instructions in the manual is forbidden.
fThe equipment is not designed to be used by people
(including children) with physical, sensory or mental
capabilities reduced or no experience or knowledge,
unless they are supervised or instructed in the use by
a person responsible for their safety.
fIt will be monitored to ensure that children do not play
with the appliance.
fThe introduction of inflammable, explosive and toxic
liquids into the appliance is prohibited.
fUse of the appliance in a potentially inflammable or
explosive atmosphere is forbidden.
fThe use of non-original spare parts and any other
spare parts not specifically intended for the model in
question is prohibited.
Warning! All modifications to the appliance are prohibited.
Any modifications made to the appliance shall render the
Declaration of Conformity null and void and relieve the
manufacturer of all liability under civil and criminal law.
Warning! Inadequate extension cords can be dangerous. If
an extension cord is used, it shall be suitable for outdoor use,
and the connection has to be kept dry and off the ground. It is
recommended that this is accomplished by means of a cord
reel which keeps the socket at least 60mm above the ground.
Warning! This machine has been designed for use
with the cleaning agent supplied or recommended by
the manufacturer. The use of other cleaning agents or
chemicals may adversely affect the safety of the machine.
Warning! High pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
live electrical equipment or the machine itself.
Warning! Do not use the machine within range of
persons unless they wear protective clothing.
Warning! Do not direct the jet against yourself or others
in order to clean clothes or foot-wear.
Warning! Risk of explosion – Do not spray flammable liquids.
Warning! High pressure cleaners shall not be used by
children or untrained personnel.
Warning! High pressure hoses, fittings and couplings
are important for the safety of the machine. Use only hoses,
fittings and couplings recommended by the manufacturer.
Warning! To ensure machine safety, use only original spare
parts from the manufacturer or approved by the manufacturer.
Warning! Water that has flowed through backflow
preventers is considered to be nonpotable.
Warning! Do not use the machine if a supply cord or
important parts of the machine are damaged, e.g. safety
devices, high pressure hoses, trigger gun.
Warning! Incorrect fuels shall not be used as they may
prove hazardous.
Warning! Do not use near people except that they use
protective clothing.
Warning! Hearing protection must be used when using
this equipment.
4. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
5. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or injury.
If the power cord is replaced by an equally qualified
person, but not authorized by BLACK+DECKER,
the warranty will not be valid.
Warning! Always switch off the mains disconnecting
switch when leaving the machine unattended.
6. Labels on tool
The label on your tool may include the following symbols:
Danger sign, warns users not to direct the water jet at people,
animals, elec- trical equipment or the product itself.
Not connect to potable water.
Read
instructions
manual
Poisoning
hazard
Injury
hazard
Explosion
hazard
Electric shock
and short
circuit hazard
Short circuit
hazard
Danger of
being beaten
by objects that
bounce
Use eye
protection
Wear proper
clothing
...... Class II
Construction
.... Safety Alert
Symbol
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
ENGLISH • 9
Warning! Safety signs. Comply with the instructions
provided by the safety signs ted to the appliance. Check
that they are present and legible; otherwise, replacements
in the original positions.
TECHNICAL INFORMATION
ENVISAGED USE
This appliance has been designed for individual use for
the cleaning of vehicles, machines, boats, masonry, etc, to
remove stubborn dirt using clean water and biodegradable
chemical detergents.
Vehicle engines may be washed only if the dirty water is
disposed of as per regulations in force.
fIntake water temperature: See data plate on
the appliance.
fIntake water pressure: Below 10 bar.
fOperating ambient temperature: Above 0 °C.
The machine complies with the IEC.
OPERATOR
The symbol on the front cover identifies the appliance’s
intended operator (professional or non-professional).
MAIN COMPONENTS (Fig. A)
The machine is delivered partially disassembled
in a carton.
1. Lance
2. Gun with safety catch
3. High pressure hose
4. Nozzle
5. Rotating nozzle
6. Adapter
7. Water filter
8. Brackets
9. Detergent kit
10. Nozzle cleaning tool
11. Screws
12. Electric cable with plug
13. Handle
14. Wheels
15. Lever
16. Hose reel
Caution! Safety devices:
fStarter device (21): The starter device prevents
accidental use of the appliance.
Do not tamper with or adjust the safety valve setting.
fSafety valve and/or pressure limiting valve:
The safety valve is also a pressure limiting valve.
When the gun trigger is released, the valve opens
and the water recirculates through the pump inlet or is
discharged onto the ground.
fThermostat valve (where fitted):
If the water temperature exceeds the temperature
set by the manufacturer, the thermostat valve
discharges the hot water and draws in an amount of
cold water equal to the amount of water discharged,
until the correct temperature is restored.
fSafety catch (20): Prevents accidental spraying of water
fOverload cutout: stops the appliance in case of overload.
INSTALLATION (Fig. B)
ASSEMBLY
Caution! All installation and assembly operations must
be performed with the appliance disconnected from the
mains power supply.
The assembly sequence is illustrated in Fig. B.
Assembling the rotating nozzle
The rotating nozzle kit delivers greater washing power.
Use of the rotating nozzle may cause of reduction in pressure
of 25% compared to the pressure obtained with the adjustable
nozzle. However, the rotating nozzle kit delivers greater
washing power due to the rotation of the water jet.
Electrical connection
Caution! Check that the electrical supply voltage
and frequency (V/Hz) correspond to those on the
appliance data plate (Fig. B8).
The appliance should only be connected to a mains power
supply equipped with an adequate earth connection and a
differential security breaker (30mA) to cut off the electricity
supply in the instance of a short circuit.
Use of extension cables: Use cables featuring “IPX5”
protection level. The cross-section of the extension cable
should be proportionate to its length; the longer it is, the
greater its cross-section should be.
Water supply connection
Caution! Only clean or filtered water should be used for
intake. The delivery of the water intake tap should be equal
to that of pump capacity. Place the appliance as close to
the water supply system as possible.
Connection points:
Water outlet (OUTLET)
Water inlet with filter (INLET)
Connection to the mains water supply
The appliance can be connected directly to the mains drinking
water supply only if the supply hose is fitted with a backflow
preventer valve as per current regulations in force. Make sure
that the hose is at least Ø 13mm and that it is reinforced.
10 • ENGLISH
ADJUSTMENT INFORMATION (Fig. C)
fAdjusting the spray nozzle: Water flow is adjusted
by regulating the nozzle (4).
fAdjusting the detergent: To deliver detergent at the
correct pressure, set the nozzle (4) (where fitted) on
“ ” or fit the detergent kit (9) as shown.
fAdjusting the pressur: The regulator is used
to adjust the working pressure. The pressure is shown
on the pressure gauge (where fitted).
USE OF THE APPLIANCE (Fig. D)
CONTROLS
Starter device (21)
Set the starter switch on (ON/I) to:
a) start the motor (in models without TSS device);
b) set the motor ready to start (in models with TSS
device). If there is a pilot light on the starter device, it
should light up. Set the starter device switch on
(OFF/0) to stop the appliance. If there is a pilot light
on the starter device, it should go out.
fWater jet control lever (19).
Warning! - Danger!
During operation the appliance must be positioned as
shown in Fig. D. on a firm, stable surface.
Start-up (Fig D)
1. Turn on the water supply tap fully.
2. Release the safety catch (20).
3. Depress the gun trigger for a few seconds and start up
the appliance using the starter device (ON/I).
Warning! - Danger!
Before starting up the appliance check that it is receiving water
correctly; use of the appliance without water will damage it. Do
not cover the ventilation grilles when the appliance is in use.
TSS models - In TSS models
(with automatic delivery flow cut-off system):
fwhen the gun trigger is released the dynamic
pressure automatically cuts out the motor;
fwhen the gun trigger is depressed the automatic
drop in pressure starts the motor and the pressure is
restored after a very slight delay;
fif the TSS is to function correctly, all gun trigger
releasing and depressing operations must be at
least 4-5 seconds apart.
To prevent damage to the appliance, do not allow it to
operate dry and check that it is properly supplied with
water. For models without TSS, to prevent damage to
the appliance due to an increase in water temperature,
do not cut off the jet of water for more than 5 minutes
with the appliance running. Beware of kickback force
when opening the trigger gun.
Stopping the appliance
1. Set the starter device switch on (OFF/0).
2. Depress the gun trigger and discharge the residual
pressure inside the hoses.
3. Engage the gun safety catch (20).
Restarting
1. Release the safety catch (20).
2. Depress the gun trigger and discharge the residual
air inside the hoses.
3. Set the starter device on (ON/I).
Storage
1. Switch the appliance off (OFF/0).
2. Remove the plug from the socket.
3. Turn off the water supply tap.
4. Discharge the residual pressure from the gun until
all the water has come out of the nozzle.
5. Drain and wash out the detergent tank at the end of
the working session. To wash out the tank, use clean
water instead of the detergent.
6. Engage the gun safety catch (20).
Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to
the surface while still dry.
When dealing with vertical surfaces work from the bottom
upwards. Leave the detergent to act for 1-2 minute but do
not allow the surface to dry. Starting from the bottom, use
the high pressure jet at a minimum distance of 30 cm. Do
not allow the rinse water to run onto unwashed surfaces.
In some cases, scrubbing with brushes is needed to
remove dirt. High pressure is not always the best solution
for good cleaning results, since it may damage some
surfaces. The finest adjustable nozzle jet setting or the
rotating nozzle should not be used on delicate or painted
parts, or on pressurised components (e.g. tyres, inflation
valves, etc.). Effective cleaning depends on both the
pressure and volume of the water used, to the same degree.
MAINTENANCE (Fig. E)
Any maintenance operations not covered by this chapter should
be carried out by an Authorized Sales and Service Centre.
¡Important! To ensure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be performed
by authorized service centers or other qualified organizations,
always using identical replacement parts. Unit contains no
user service able parts inside.
Caution! Always disconnect the plug from the power
socket before carrying out any work on the appliance.
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Sprachen:
Andere BLACK DECKER Hochdruckreiniger Handbücher
BLACK DECKER
BLACK DECKER PW1450TD Bedienungsanleitung
BLACK DECKER
BLACK DECKER BCPC18D1 Bedienungsanleitung
BLACK DECKER
BLACK DECKER PW1300TDW Betriebsanleitung
BLACK DECKER
BLACK DECKER BXPW1300E Bedienungsanleitung
BLACK DECKER
BLACK DECKER PW 1370 TD Bedienungsanleitung
BLACK DECKER
BLACK DECKER BXPW2500DTS Bedienungsanleitung
BLACK DECKER
BLACK DECKER BXPW1300E Bedienungsanleitung
BLACK DECKER
BLACK DECKER BXPW1300E Bedienungsanleitung
