Black Horse Model GLASAIR Betriebsanleitung

SPECIFICATION

1Wingspan: 1,860 mm 73.23 in.

1Length :1,470 mm 57.87 in.

1Weight : 5.2 kg 11.44 lbs.

Parts listing required (not included):

1Radio : 06 channels.

1Servo : 08 servos.

1Engine : 91-120 2 stroke.

Instruction Manual Book

MadeinVietnam.

GLASAIR - Item code: BH74 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manualthoroughlybeforestartingassemblyofyour GLASAIR.Usethepartslistingbelowtoidentify

all parts.

WARNING

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED

1Thick cyanoacrylate glue.

130 minute epoxy.

15 minute epoxy.

1Hand or electric drill.

1Assorted drill bits.

1Modellingknife.

1Straightedge ruler.

12mm ball driver.

1Phillips head screwdriver.

1220 grit sandpaper.

190° square or builder’s triangle.

1Wire cutters.

1Masking tape & T-pins.

1Thread-lock.

1Paper towels.

Some more parts.

HARDWARE PACK

COWLING.

Landinggear.....

Toavoidscratching yournew airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftandto protectthetable. Keepacoupleof

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrialfitalltheparts.Makesureyouhave

the correct parts and that they fit and are

alignedproperlybefore gluing!Thiswill assure

properassembly. GLASAIR ARFis handmade

from natural materials, every plane is unique

andminoradjustmentsmay have to bemade.

However, you should find the fit superior and

assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

ofmanyharshchemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderandacetone.Donotletthesechemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING

FUSELAGE ASSEMBLY

1(1) Fuselage.

WING ASSEMBLY

1(1) Right wing half with pre-installed

aileron.

1(1) Left wing half with pre-installed

aileron.

Tail section assembly

1(1) Vertical stabilizer with pre-

installedrudder.

1(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION

NOTE.

GLASAIR - Item code: BH74 . Instruction Manual

+ This is not a toy

+ Be sure that no other flyers are using your radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from children and pets.

+ Wear safety glasses.

+The glow plug clip must be securely attached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from the propeller.

+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.

+ Make engine adjustments from behind the propeller only. Do not reach around the spinning

propeller.

SAFETY PRECAUTION.

REPLACEMENT LARGE PARTS

B. Wing panel.

C. Fuselage.

A.Cowling. D.Horizontal stabilizer.

F. Aluminium wing dihedral brace.

E.Vertical stabilizer. G. Decal sheet.

K. Pilot.

REPLACEMENT SMALL PARTS

4x30mm

3x15mm 3x10mm

5x50mm. 5x50mm.

GLASAIR - Item code: BH74 . Instruction Manual

12)Usingamodeling knife, removethecov-

ering at possition show below.

Cutthe covering

awayfromtheslot.

Temporary pin to

keep hinge centered.

Assemble then apply drops of thin

C/A to center of hinge,on both sides.

Bottom side.

Servo tray

Remove

covering

Secure

6.Spinner.

5. Plastic - enginemount.

2. Wheels

4. Fuel tank.

10. Tail gear set.

3. Wheel pants.

7. Plastic parts for landing gear fuselage.

1. Aluminiumlandinggear.

11. Plastic parts for tail gear.

8.Electric wing light tray.

9. Rudder plastic light.

11) Install the rubber grommets and brass

eyelets onto the aileron servos.

I.AILERON.

1.INSTALLING THE AILERON SERVOS.

Bottom side.

Flap Aileron

GLASAIR - Item code: BH74 . Instruction Manual

14)Drill1,6mmpilotholes through the block

of wood for each of the four mounting screws

provided with the servo.

13) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

o5. Instal servo tray with aileron servo into

the wing as same as picture below.

2x10mm.

Secure.

Install aileron control horn as same as picture

below. Controlhornof Aileron

INSTALLINGTHEAILERON CONTROL HORN.

Electric wire

Thread

A+B Epoxy

PLUSglue.

Drill a hole 1.7mm

diameter

GLASAIR - Item code: BH74 . Instruction Manual

16.Insertthe90degree bend down through

the hole in the servo arm. Install one nylon

snap keeper over the wire to secure it to the

arm.Install theservoarm retainingscrewand

remove the masking tape from the aileron.

Cut

Bendand

cut after

11.Working withthe aileron linkage fornow,

thread one clevis onto one of the threaded

wires.

13. Plug the aileron servo into the receiver

andcenter theservo. Installthe servoarm onto

the servo. The servo arm should be perpen-

dicular to the servo and point toward the mid-

dle of the wing.

12. Attach the clevis to the outer hole in the

control horn.

14. Locate one nylon servo arm, and using

wire cutters,remove all but one of the arms.

Using a 2mm drill bit, enlarge the third hole

out from the center of the arm to accommo-

date the aileron pushrod wire.

15. Using pliers, carefully make a 90 degree

bend down at the mark made. Cut off the ex-

cess wire, leaving about 4mm beyond the

bend.

Repeat the procedure for the other wing

half.

Aileron

control horn

M2 lock nut Snapkeeper.

M2 100mm

3.INSTALLING THE AILERON

LINKAGES.

GLASAIR - Item code: BH74 . Instruction Manual

Secure.

2.INSTALLING THE FLAP CONTROL HORN.

Drill a hole 1.7mm

diameter

Flap control

horn

Flap controlhorn

Installflap controlhorn assame as

picturebelow.

A+B Epoxy

PLUS glue

Flap

1.INSTALLING THE FLAP SERVOS.

II. FLAP.

2x10mm.

Remove

covering

GLASAIR - Item code: BH74 . Instruction Manual

See pictures below:

Cut.

Repeat the procedure for the other wing

half.

INSTALLING THE ENGINE MOUNT.

Flap Bottom side.

Installing the Flap linkages as pictures

below.

3.INSTALLING THE FLAP

LINKAGES.

M2 lock nut Snapkeeper.

M2 100mm

Drill a hole

5.2mm diam-

eter.

4 x 30mm

GLASAIR - Item code: BH74 . Instruction Manual

13) Carefully bend the second nylon tube

up at a 45 degree angle (using a cigarette

lighter). This tube will be the vent tube to the

muffler.

14) Carefullybendthe thirdnylontube down

ata45 degreeangle (usingacigarette lighter).

This tubewillbe venttubeto the fuelingvalve.

INSTALLING THE STOPPER ASSEMBLY

11) The stopper has been pre-assembled

at the factory.

12) Using a modeling knife, cut one length

ofsiliconfuelline (the lengthofsilicon fuel line

iscalculatedbyhowthe weightedclunkshould

restabout8mmaway from therearofthe tank

andmovefreelyinside the tank).Connectone

end of the line to the weighted clunk and the

otherendtothe nylon pickuptube in thestop-

per.

When the stopper assembly is installed in the

tank, the top of the vent tube should rest just

belowthetop surface ofthetank. It shouldnot

touch the top of the tank.

15) Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

amodelingknife. If flashing is present, make

sure none of it falls into the tank.

16) Whensatisfiedwiththe alignment of the

stopper assembly tighten the 3mm x 20mm

machine screw until the rubber stopper ex-

pandsandseals thetank opening.Donot over

tighten the assembly as this could cause the

tank to split.

Vent tube Fuel pick- up tube

Fuelfilltube

FUEL TANK.

Silicon tube not included

17) Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.

GLASAIR - Item code: BH74 . Instruction Manual

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel tank compartment. Air should flow

through easily.

19) To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

thetank,where itexitsthe fuselagebehindthe

enginemounting boxand tothe rearof thetank

at the forward bulkhead.

Do not secure the tank into place perma-

nently until after balancing the airplane. You

may need to remove the tank to mount the

battery in the fuel tank compartment

18) Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible,thefront ofthe tankshouldjust about

touch the back of the firewall.

Fueltank

Andere Handbücher für GLASAIR

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Black Horse Model Spielzeug Handbücher

Black Horse Model

Black Horse Model NOORDUYN NORSEMAN Betriebsanleitung

Black Horse Model

Black Horse Model BH36-A Betriebsanleitung

Black Horse Model

Black Horse Model Arrow 3D Betriebsanleitung

Black Horse Model

Black Horse Model BH172 Betriebsanleitung

Black Horse Model

Black Horse Model MESSERSCHMITT BF-109E Betriebsanleitung

Black Horse Model

Black Horse Model ORBIT BH106 Bedienungsanleitung

Black Horse Model

Black Horse Model GILMORE BH179 Betriebsanleitung

Black Horse Model

Black Horse Model SUPER TUCANO BH173 Betriebsanleitung

Black Horse Model

Black Horse Model Extra 300S Betriebsanleitung

Black Horse Model

Black Horse Model SU 26M-EP Betriebsanleitung

Black Horse Model

Black Horse Model MKII Betriebsanleitung

Black Horse Model

Black Horse Model BH136A Betriebsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model P-36A Hawk Bedienungsanleitung

Black Horse Model

Black Horse Model Extra 300S Bedienungsanleitung

Black Horse Model

Black Horse Model DECATHLON-EP Betriebsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model Cobra Betriebsanleitung

Black Horse Model

Black Horse Model Spitfire MK Betriebsanleitung

Black Horse Model

Black Horse Model Travel Air BH.06 Betriebsanleitung

Black Horse Model

Black Horse Model L-39 Albatros Betriebsanleitung

Black Horse Model

Black Horse Model YAK 11 Betriebsanleitung

Black Horse Model

Black Horse Model EP-TRAINER Betriebsanleitung

Black Horse Model

Black Horse Model TAYLORCRAFT BH 134 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung