Black Widow REMOTE START SECURITY SYSTEM Bedienungsanleitung

OWNERS MANUAL

REMOTE START SECURITY SYSTEM

Standard Features

The System has the following standard features:

• 5-button remote transmitter

• Status indicator (LED)

• Valet/Service mode switch

• Remote Start capabilities

• Extended Range Receiver

• Multi-tone siren (126dB)

• Dual stage impact detector

• Remote panic

• Valet mode

• Remote chirp delete

• Remote sensor bypass

• Passive or active arming

• Stop & Go Feature

• Auto Cold Start

• Flashing parking lights

• Auto Rearm

• Passive/Active Arming

Optional Features

This System has many optional features that may

require additional parts and/or labor. Please contact

your dealer for more details.

•Remote keyless entry (Door lock/unlock)

•Illuminated entry

•LCD FM 2-way Remote

•Hood & trunk protection

•Horn honk

•Trunk/hatch release

•Window roll-up

•Back up battery

•Additional sensors: glass breakage/microwave

Note: Some features may not be appropriate for

certain vehicles. Automatic transmission and

electronic fuel injection are required. on vehicles for

use with this system.

REMOTE TRANSMITTER FUNCTIONS

Button I Arms the system and locks the

doors*. Button I also activates the Panic

feature.

Button 2 Disarms the system and unlocks the

doors*.

Button 3 Activates the optional Trunk Release

feature*.

Button 4 Activates the Remote Start Feature.

Button 5 Auxiliary Shift Key.

Buttons 5 then 4 Activates the 2nd auxiliary

function.

* Optional Feature

Button 1

5-Button

Transmitter

Button 3

Button 2

Button 5

Button 4

Security System Operation

ARMING OPERATION

To arm the system press transmitter button 1:

•The siren will chirp once. -

•The parking lights will flash once.

•The doors will lock*.

•The L.E.D. will turn solid for 10 seconds

then start flashing slowly, the system - is

now armed.

While the system is armed the alarm will

trigger if

•A door is opened.

•The hood/trunk is opened*.

•The shock sensor detects an impact to the

vehicle.

When the alarm is triggered the siren will sound, the

parking lights will flash, and the horn will honk*. If the

alarm is triggered while the remote start is engaged,

the remote start will immediately shut down.

PASSIVE ARMING

The passive arming feature allows the system to

arm automatically without user intervention.

This programmable feature may be enabled during

installation.

To arm the system passively:

1.Turn the ignition key off.‡

2.Exit the vehicle and close all doors.

•The LED will start flashing rapidly to indicate

that the system is preparing to arm. (The

system can be armed at any time by pressing

transmitter button 1.)

•The siren will chirp 30 seconds after

the last door is closed to indicate the

system is now armed.

•The doors will lock.†*

‡The ignition must have been on for at least 10 seconds prior to

exiting the vehicle or Passive Arming will be bypassed.

†If the Passive Locking feature was enabled during installation.

DISARMING OPERATION

To disarm the system press transmitter button 2.

•The siren will chirp twice.¥

•The parking lights will flash twice.¥

•The doors will unlock.†*

•The dome light will turn. on for 30

seconds.*

¥If the alarm was triggered while away, the system will respond

with 3 chirps and 3 parking light flashes.

†If the Passenger Unlock Feature is enabled, pressing the unlock

button will unlock only the driver’s door. Pressing the unlock

button again unlocks all doors.

TAMPER ALERT

If the alarm was triggered while away from the vehicle, the

siren will chirp 3 times on disarming for tamper indication.

After disarming the alarm, enter vehicle and turn ignition

on. The LED will flash the zone that was triggered 5

times (see LED chart).

AUTO REARM

The Auto Rearm feature allows the system to

automatically re-arm itself in the event the

system is disarmed and ignition is not turned on

within 30 seconds.

NOTE: This programmable feature may be disabled

during installation. The Passive Arming feature and Auto

Rearm feature are related In order to disable the Auto

Rearm feature, the Passive Arming feature must also be

disabled during installation. This feature will not work on

vehicles with the illuminated entry feature enabled

SILENT ARMING/DISARMING

Press transmitter button 5 (the Shift Button)

then the Arm or Disarm button for one-time

silent operation.

* Optional Feature

CHIRP DELETE

For full time silent operation, the ARM/ DISARM

chirps can be permanently disabled.This feature must

be programmed during installation.

IGNITION LOCK*

The ignition locking feature allows the doors to

automatically lock when the ignition key is turned on,

and automatically unlock when the ignition key is

turned off. This feature may be disabled during

installation.

REMOTE PANIC

In the event of an emergency (PANIC) situation, the

system’s siren can be triggered for 45 seconds to

attract attention.To activate the Panic Feature, press

transmitter button I for 3 seconds:

•The siren will chirp once.

•To exit Valet Mode:

•The siren will sound.

•The parking lights will flash.

Press button I to exit panic mode and rearm

the system. Press button 2 to exit panic mode

and disarm the system.The Panic Feature will

operate when the ignition is on.

EMERGENCY OVERRIDE

If the ‘transmitter becomes lost or fails to

operate, the system can be disarmed by using

the emergency override feature.

To override the system:

1. Enter the vehicle.

Because the system is armed, the siren

will sound.

2.Turn on the ignition key.

3. Press the Valet switch for 5 seconds.

The siren will stop sounding.

Starter defeat bypassed.

VALET MODE

When the system is placed into the Valet Mode

the security system will be disabled. However, the

optional keyless entry and trunk release and

remote start features will still function if

installed.

NOTE: Remote Start feature maybe disabled

during valet mode if programmed during

installation.

To enter the Valet Mode:

I . Be sure the system is disarmed.

2.Turn the ignition key on.

3.Press and hold the valet/service mode

switch for 3 seconds.

•The LED will chirp once.

•The LED will turn on solid indicating

the system is in Valet Mode.

To exit the Valet Mode:

1. Turn the ignition key on.

2. Press and hold the valet/service mode

switch for 3 seconds.

•The LED will turn off.

•The Siren will chirp 2 times.

OPTIONAL TRUNK RELEASE

Press button 3 for approximately 2 seconds to open

the trunk.

OPTIONAL TRUNK DISARM

The trunk disarm feature allows the alarm to

disarm automatically whenever transmitter

button 3 is used to activate the optional trunk

release.This eliminates having to first disarm

the alarm before activating the trunk release.

NOTE: This feature must be programmed during

installation.

REMOTE SENSOR BYPASS

To arm the system and bypass the shock sensor, press

button I to arm, then within 2 seconds press button I

again.The siren will chirp 5 times and sensors will be

ignored until the

* Optional Feature

system is disarmed and rearmed.

OPTIONAL SECURE

OVERRIDE CODE

If your system was programmed to override with a

personal override code-pressing the override switch

from I to 15 times.

To disarm the system with your personal override

code please use the following steps:

1. Open Door Alarm system will trigger

2.Turn ignition key to on

3. Press the override switch to the selected number

of times and hold on the last one for 5 seconds until

the alarm turns off.

Remote Start Operation

Important: Only start the vehicle in a well

ventilated area. Do not use in a closed garage or

indoors. Be sure to familiarize yourself with all

features prior to using this product.

REMOTE STARTING THE VEHICLE

To remote start the vehicle:

Press transmitter button 4 for 3 seconds.

•The parking lights turn on.

•Approximately 2 seconds later the system will

attempt to start the vehicle.

•Once the car has started, the heater or air

conditioner will turn on and run for the

pre-programmed time (15 or 25 minutes). If the

engine fails to start on the first attempt, it will

repeat the starting procedure 2 more times.If the

vehicle fails to start after a total of 3 times the

system will shut down.

Driving vehicle after Remote Starting:

Unlock the door by pressing button 2* on

the remote transmitter. Enter vehicle, turn ignition

key to the on position (Note: Do not turn the key all

the way to the start position as you may damage the

starter).

Once the ignition key is turned to the on position,

press the brake pedal and shift the car into the

proper gear and you may now drive the vehicle

(Note: If broke pedal is pressed prior to turning on

ignition, engine will turn off).

REMOTE ENGINE SHUTDOWN

If the vehicle has been remotely started and you

desire to turn the vehicle off, simply press and hold

button 4 on the remote transmitter for three

seconds. After the motor has turned off the doors

will relock*.This feature must be programmed during

installation.

AUTO COLD START

This feature allows the system to start and run the

vehicle every one or two hours (selectable by your

installer) for a period of 24 hours.This allows the

engine to remain at an operational temperature in

extremely cold weather. Auto Cold Start must be

enabled during installation or it cannot be engaged.

Engaging the Auto Cold Stan feature:

To turn Auto Cold Start on:

1. Press and hold the brake pedal.

2. While holding the brake pedal down, push the

Valet switch and transmitter button 2 for two

seconds.

•The parking lights will flash four times to

indicate the Cold Start feature is engaged.

3. Release the brake pedal.

* Optional Feature

Disengaging the Auto Cold Start feature:

The Auto Cold Start feature can be

deactivated in one of three ways:

•Press the brake pedal.

•Turn on the ignition.

•Remote start the vehicle using the

transmitter.

STOP AND GO

The Stop and Go feature allows the vehicle to remain

running without use of the ignition key during short

stops.

To activate the Stop and Go feature:

1. With engine running push transmitter

button 4 (on FM 2-way press button 2.). - The

parking lights will turn on.

2. Remove the key from the ignition.

3. Exit the vehicle and lock the doors manually or

using transmitter button 1*.

To resume driver control:

1. Unlock the doors manually or by pressing

transmitter button 2*.

2. Turn on the ignition.

•The vehicle resumes driver control,

SAFETY FEATURES

The System will not start the vehicle if the brake

pedal is pressed or the hood is open.Also, if the brake

is pressed or the hood is opened while- remote

running, the remote start will shut down.

REPLACING LOST OR STOLEN

REMOTE TRANSMITTERS

This System can “learn”a maximum of 4 remote

transmitters.To add a transmitter or replace

lost/stolen transmitters, please consult with an

authorized Black Widow Dealer.

* Optional Feature

SYSTEM REFERENCE INDICATORS

STATUS INDICATOR (LED) FUNCTIONS

On Solid =Valet Mode

Slow Flash System Armed

Rapid Flash Passive Arming

TAMPER ALERT LED FUNCTIONS

I flash ‘= sensor #22 flashes = shock sensor

4 flashes = door

5 flashes = hood or trunk

flash-flash-pause-flash-flash-pause = shock sensor

PARKING LIGHTS FUNCTIONS

On Solid =Vehicle Remote Starting

Flash I x =System armed

Flash 2x = System disarmed

Flash 3x =Tamper indication (after disarming)

Flash 4x = Defective zone warning

(after arming)

Inhaltsverzeichnis

Andere Black Widow Autoalarmanlage Handbücher

Black Widow

Black Widow 1 Channel Bedienungsanleitung

Black Widow

Black Widow BW 2800 Bedienungsanleitung

Black Widow

Black Widow BW-2000 CLASSIC Bedienungsanleitung

Black Widow

Black Widow BW 3150 Bedienungsanleitung

Black Widow

Black Widow BW 550 Bedienungsanleitung

Black Widow

Black Widow BW-1500 CHALLENGER PLUS Bedienungsanleitung

Black Widow

Black Widow BW-1400 CHALLENGER Bedienungsanleitung

Black Widow

Black Widow BW 550 Bedienungsanleitung

Black Widow

Black Widow BW 4150 Bedienungsanleitung

Black Widow

Black Widow BW 2450 Bedienungsanleitung

Black Widow

Black Widow BW-2500 PREMIER Bedienungsanleitung

Black Widow

Black Widow BW 3150 Bedienungsanleitung

Black Widow

Black Widow BW-2000 CLASSIC Bedienungsanleitung

Black Widow

Black Widow BW-1150 EXPLORER PLUS Bedienungsanleitung

Black Widow

Black Widow BW 4100 Bedienungsanleitung

Black Widow

Black Widow BW-2500 PREMIER PLUS Bedienungsanleitung

Black Widow

Black Widow BW-800 SMART SYSTEM Kurzanleitung

Black Widow

Black Widow BW 2800 Bedienungsanleitung

Black Widow

Black Widow BW 2850 Bedienungsanleitung

Black Widow

Black Widow 5-BUTTON SERIES Bedienungsanleitung

Black Widow

Black Widow BW-1000 AVENGER Bedienungsanleitung

Black Widow

Black Widow BW-1500 Bedienungsanleitung

Black Widow

Black Widow 1R / 2-BUTTON SERIES Bedienungsanleitung

Black Widow

Black Widow BW1700 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung