Blizzard Lighting Switchblade Bedienungsanleitung

Blizzard Lighting, LLC

www.blizzardlighting.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

SwitchBlade™ LED 1

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of The Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions (Don’t Stick Your Head In The Oven!) 4

2. Meet The SwitchBlade™ LED 5

Features 5

DMX Quick Reference 5

The SwitchBlade™ Pin-up Picture 6

3. Setup 7

Fuse Replacement 7

Connecting A Bunch Of SwitchBlade™ Moving Heads 7

Data/DMX Cables 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh? 8

Take It To The Next Level: Setting up DMX Control 8

Fixture Linking (Master/Slave Mode) 9

Mounting/Rigging 9

4. Operating Adjustments 10

Navigating The Control Panel 10

Control Panel Menu Structure 11

DMX Mode 11

Master/Slave Mode 11

Sound Active Mode 11

Standalone (Program) Mode 11

Manual Color Adjustment 11

DMX Channel Values In-Depth 12

Troubleshooting 13

5. Appendix 14

Keeping Your SwitchBlade™ As Good As New 14

Returns (Gasp!) 14

Shipping Issues 14

Tech Specs 15

Page 3

1. GETTING STARTED

What’s In The Box?

• 1 x SwitchBlade™ Ultra Sharp LED Moving Head Fixture

• 1 x All important power cord

• A Mounting Bracket and Safety Cable

• Some Styrofoam

• This User Manual

Getting It Out Of The Box

Are you bad? If not you can Beat It. MJ made the SwitchBlade™ famous in his classic

1984 video. We ﬁgure if someone publicly used a SwitchBlade™ in today’s society they

would be the chastised for promoting violence. Since we like a challenge, we introduce

to you The SwitchBlade™. You now own a one of a kind Moving Head with one of the

sharpest beams in the industry. Now that you’ve got your SwitchBlade™, you should

carefully unpack the box and check the contents to ensure that all parts are present

and in good condition. If anything looks as if it has been damaged in transit, notify the

shipper immediately and keep the packing material for inspection. Again, please save

the carton and all packing materials. If a ﬁxture must be returned to the factory, it is

important that the ﬁxture be returned in the original factory box and packing.

Powering Up!

All ﬁxtures must be powered directly off a switched circuit and cannot be run off a

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch.

AC Voltage Switch - Not all ﬁxtures have a voltage select switch, so please verify that

the ﬁxture you receive is suitable for your local power supply. See the label on the

ﬁxture or refer to the ﬁxture’s speciﬁcations chart for more information. A ﬁxture’s

listed current rating is its average current draw under normal conditions. Check the

ﬁxture or device carefully to make sure that if a voltage selection switch exists that it is

set to the correct line voltage you will use.

Warning! . All ﬁxtures must be connected to circuits with a suitable Ground

(Earthing).

Getting A Hold Of Us

If something is wrong, just give us a call or send an email. We’ll be happy to

help, honest.

Blizzard Lighting

N16 W23390 Stoneridge Dr. Ste E

Waukesha, WI 53188 USA

www.blizzardlighting.com

414-395-8365

Email: [email protected]

Disclaimer: The information and speciﬁcations contained in this document are subject

to change without notice. Blizzard Lighting™ assumes no responsibility or liability

for any errors or omissions that may appear in this user manual. Blizzard Lighting™

reserves the right to update the existing document or to create a new document to

correct any errors or omissions at any time. You can download the latest version of this

document from www.blizzardlighting.com.

Author: Date: Last Edited: Date:

Stevie Ray 1/5/2014 W. Komassa 1/7/2014

Page 4

SAFETY INSTRUCTIONS

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the ﬁxture.

• This product is intended for indoor use only.

• To prevent risk of ﬁre or shock, do not expose ﬁxture to rain or moisture.

• Make sure there are no ﬂammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Do not block any ventilation slots.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure ﬁxture using a safety chain. NEVER carry the ﬁxture by its

cord. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

• Carrying a SwitchBlade™ under your jacket may be viewed as a concealed

weapon by law enforcement.

Caution! There are no user serviceable parts inside the unit. Do not

open the housing or attempt any repairs yourself. In the unlikely event

your unit may require service, please contact Blizzard Lighting at sup-

[email protected].

Page 5

2. MEET THE SWITCHBLADE™ LED MOVING HEAD

CONTROL FEATURES

• 1x CREE XLamp MC-E 4-IN-1 10W LED

• 50,000 hours lifespan and low power consumption

• Narrow 2 degree beam angle

• Outstanding beam effects

• High efﬁciency LED shutter

• 8 built-in default programs for easy performance

• Amazing beam color splitting effects

• Built-in sound active programs

• 10/12 DMX Channels

• Built-in color & chase macros via DMX, Sound, and Auto Modes

• DMX512, master-slave, sound activated, auto mode

ADDITIONAL FEATURES

• 4-button LCD display control panel menu

• Efﬁcient low noise fan cooling system

• 3-pin XLR connectors IN/OUT

• 420 Lux (R), 492 Lux (G), 610 Lux (B) and 1070 Lux (W) @7M

• 1/4 turn fastening Omega Clamp

DMX Quick Reference - 12 / 10 Channel Mode

Ch 12 Channel 10 Channel

1 Pan Pan

2 Pan Fine Tilt

3 Tilt Speed

4 Tilt Fine Shutter

5 Speed Dimmer

6 Shutter Red

7 Dimmer Green

8 Red Blue

9 Green White

10 Blue Special

11 White

12 Macros

Page 6

Figure 1: The SwitchBlade™ Pin-Up Picture

High Power OSRAM 4-in-1

Quad Color RGBW LED

4 Button Controls

and LCD Display

Figure 2: Behind The Beam

DMX InDMX Out

AC Power In

Super Fast Single Arm

Rotating Yoke

Ergonomically

Correct Handles

Super Sharp

2 Degree Beam

Fuse Power Switch

Page 7

3. SETUP

Fuse Replacement

CAUTION! With a ﬂat head screwdriver, wedge the fuse holder out

of its housing. Remove the damaged fuse from its holder and replace

with exact same type fuse. Insert the fuse holder back in its place and

reconnect power.

Connecting A Bunch of SwitchBlade™ Fixtures

You will need a serial data link to run light shows using a DMX-512

controller or to run shows on two or more ﬁxtures set to sync in mas-

ter/slave operating mode. The combined number of channels required

by all the ﬁxtures on a serial data link determines the number of ﬁx-

tures the data link can support.

Fixtures on a serial data link must be daisy chained in one single line.

Also, connecting more than 32 ﬁxtures on one serial data link without

the use of a DMX optically-isolated splitter may result in deterioration

of the digital DMX signal.

The maximum recommended cable-run distance is 500 meters (1640

ft). The maximum recommended number of ﬁxtures on a serial data

link is 32 ﬁxtures.

Data/DMX Cabling

To link ﬁxtures together you’ll need high quality data cables (may I

recommend Cool Cables). You should use data-grade cables that can

carry a high quality signal and are less prone to electromagnetic inter-

ference

(Cough did I mention Cool Cables?)

For instance, Belden© 9841 meets the speciﬁcations for EIA RS-485

applications. Standard microphone cables will “probably” be OK, but

note that they cannot transmit DMX data as reliably over long distanc-

es. In any event, the cable should have the following characteristics:

2-conductor twisted pair plus a shield

Maximum capacitance between conductors – 30 pF/ft.

Maximum capacitance between conductor & shield – 55 pF/ft.

Maximum resistance of 20 ohms / 1000 ft.

Nominal impedance 100 – 140 ohms

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR

connector on the other end. (Duh!)

CAUTION: Do not allow contact between the common and the ﬁx-

ture’s chassis ground. Grounding the common can cause a ground

loop, and your ﬁxture may perform erratically. Test cables with an

ohm meter to verify correct polarity and to make sure the pins are not

grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.

They are widely available over the internet and from specialty retailers If you’d like to build your own, the

chart below details a proper cable conversion:

Conductor 3-Pin Female

(Output) 5-Pin Male

(Input)

Ground/Shield Pin 1 Pin 1

DMX Data (-) Pin 2 Pin 2

DMX Data (+) Pin 3 Pin 3

Not Used. No Connection. No Connection.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the

DMX cable to the female connector (output)

on the controller.

Step 2: Connect the female connector of the

DMX cable to the ﬁrst ﬁxture’s male connec-

tor (input). Note: It doesn’t matter which

ﬁxture address is the ﬁrst one connected.

We recommend connecting the ﬁxtures in

terms of their proximity to the controller,

rather than connecting the lowest ﬁxture

number ﬁrst, and so on.

Step 3: Connect other ﬁxtures in the chain

from output to input as above. Place a DMX

terminator on the output of the ﬁnal ﬁxture

to ensure best communication.

Page 9

Fixture Linking (Master/Slave Mode)

1. Connect the (male) 3 pin connector side of the

DMX cable to the output (female) 3 pin connector of

the ﬁrst ﬁxture.

2. Connect the end of the cable coming from the

ﬁrst ﬁxture which will have a (female) 3 pin connec-

tor to the input connector of the next ﬁxture con-

sisting of a (male) 3 pin connector. Then, proceed

to connect from the output as stated above to the

input of the following ﬁxture and so on.

A quick note: Often,

the setup for Master-

Slave and Standalone

operation requires that

the ﬁrst ﬁxture in the

chain be initialized for

this purpose via either

settings in the control

panel or DIP-switches.

Secondarily, the ﬁxtures

that follow may also re-

quire a slave setting.

Check the “Operating Adjustments” section in this manual for com-

plete instructions for this type of setup and conﬁguration.

Mounting & Rigging

This ﬁxture may be mounted in any SAFE position provided there is

enough room for ventilation.

It is important never to obstruct the fan or vents pathway. Mount the

ﬁxture using a suitable “C” or “O” type clamp. The clamp should be

rated to hold at least 10x the ﬁxture’s weight to ensure structural sta-

bility. Do not mount to surfaces with unknown strength, and ensure

properly “rated” rigging is used when mounting ﬁxutres overhead.

Adjust the angle of the ﬁxture by loosening both knobs and tilting the

ﬁxture. After ﬁnding the desired position, retighten both knobs.

• When selecting installation location, take into consideration lamp

replacement access (if applicable) and routine maintenance.

• Safety cables MUST ALWAYS be used.

• Never mount in places where the ﬁxture will be exposed to rain,

high humidity, extreme temperature changes or restricted ventilation.

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

All the goodies and different modes possible with the SwitchBlade™

LED are accessed by using the control panel on the front of the ﬁxture.

There are 4 control buttons below the LED display which allow you to

navigate through the various control panel menus.

<MENU>

Is used to navigate to the previous higher-level menu item.

<UP>

Scrolls through menu items and numbers in ascending order.

<DOWN>

Scrolls through menu items and numbers in descending order.

<ENTER>

Is used to select and conﬁrm/store the current selection.

The Control Panel LED Display shows the menu items you select from

the menu map on page #11. When a menu function is selected, the

display will show immediately the ﬁrst available option for the selected

menu function. To select a menu item, press <ENTER>.

Press the <MENU> button repeatedly until you reach the desired

menu function. Use the <UP> and <DOWN> buttons to navigate the

menu options. Press the <ENTER> button to select the menu function

currently displayed, or to enable a menu option. To return to the previ-

ous option or menu without changing the value, press the

<MENU> button.

Inhaltsverzeichnis

Andere Blizzard Lighting DJ-Equipment Handbücher

Blizzard Lighting

Blizzard Lighting ENIGMA M4 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Torrent FZ Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Laser Blade G Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting MiniSystem Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting LB HEX Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Tour QT Skywire Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting PROPAR COB RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Q-Stick RGBW LED Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Kaptivator Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ThunderStik Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting G-Max 200 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Stiletto Glo 19 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting StormChaser Skywire RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting TOUGHPAR ZOOM RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting ToughSTICK RGBAW Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting N-Trance Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Super-G 150 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting SwitchBlade Micro Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting STILETTO I7 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Cyc Out Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Redstone 240Z Wash Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Propar Z19 Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting weather system Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Weather System EXA Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

Blizzard Lighting switchblade Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken