BLOTZ B28-OW-113 Bedienungsanleitung

28mm Old West Store #6

B28-OW-113

Assembly Instructions

Designed and made in the UK.

This is a model kit and is not intended for persons

under 14 years old.

Requires assembly. Supplied unpainted.

28mm Old West Front #4

B28-OW-403

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the two base pieces and the frame from the

sprue.

Glue the frame to the plank section, then glue the

other base section under it using the lugs to align

them.

Glue the rear plate into place.

While the assembly dries, place it against a rear

section to ensure it doesn’t tilt forwards.

Take the insert pieces from the sprue.

Glue these into the gaps in the framework.

The windows and sill.

Glue the sill into place at the bottom of the window

gap, then glue the window into place, along with the

one above the door.

Take the door and supports from the sprue.

Glue the lower support into place. Allow to dry.

Place the lower lug of the door into the lower support,

then sit the upper support onto the top lug before

gently easing it into place (see example pic).

Apply some glue to the upper support and then slide

it completely into position.

The decorative supports.

Glue these into the holes in the top of the frame.

The top bar and signs.

Glue your desired sign and top bar into position.

The completed front.

28mm Old West Rear #1

B28-OW-500

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the two base pieces and the inner walls from

the sprue.

Glue the walls to the planked base so that all etched

detail Is facing inwards (see pic).

Note: Two lugs will extend through the floor.

Glue the base plate into position, using the lugs to

align it.

Take the frame pieces from the sprue.

Glue the end frame into place.

Then add the side frames. The thinner part of the

frame (with the sprue points on it) should be at the

bottom.

The insert panels for the sides.

Pop these into position.

The insert panels for the end.

Glue these into place.

Take the door and supports from the sprue.

Glue the lower support into place. Allow to dry.

Place the lower lug of the door into the lower

support, then sit the upper support onto the top lug

before gently easing it into place (see pic).

The window sills.

Glue a sill below each window.

The completed rear.

28mm Old West Roof #5

B28-OW-604

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the pieces shown above from the sprue.

Glue the support bars through the holes in the roof

plate.

Glue the end pieces and ridge bar into place.

The end “frames”

The blank “frame” goes at the end nearest the support

bars. The open frame goes in the other end (see pic)

Add the insert pieces into the frame.

Glue the roof pieces into place.

The roof strips.

Glue the strips into place.

The completed roof.

28mm Old West Porch #2

B28-OW-651

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the pieces of the porch from the sprue.

Glue the ends to the front as shown above.

Glue the roof into position.

Attach the porch to a building of your choice such as

the one shown above.

Andere BLOTZ Spielzeug Handbücher

BLOTZ

BLOTZ B10-CS-102 Bedienungsanleitung

BLOTZ

BLOTZ B28-WW2-303 Bedienungsanleitung

BLOTZ

BLOTZ Old West Store #7 Bedienungsanleitung

BLOTZ

BLOTZ B20-ME-009 Bedienungsanleitung

BLOTZ

BLOTZ Shako Rocket Tosen Bedienungsanleitung

BLOTZ

BLOTZ B28-WW2-300 Bedienungsanleitung

BLOTZ

BLOTZ B06-MW-100 Bedienungsanleitung

BLOTZ

BLOTZ B20-ST-102 Bedienungsanleitung

BLOTZ

BLOTZ B10-MW-108 Bedienungsanleitung

BLOTZ

BLOTZ B15-CS-002 Bedienungsanleitung

BLOTZ

BLOTZ B28-SF-226 Bedienungsanleitung

BLOTZ

BLOTZ B28-WW2-101 Bedienungsanleitung

BLOTZ

BLOTZ B15-WW2-100 Bedienungsanleitung

BLOTZ

BLOTZ B28-VSF-010 Bedienungsanleitung

BLOTZ

BLOTZ B20-DIDG Series Bedienungsanleitung

BLOTZ

BLOTZ B15-CS-251 Bedienungsanleitung

BLOTZ

BLOTZ B06-CS-010 Bedienungsanleitung

BLOTZ

BLOTZ B10-MW-112 Bedienungsanleitung

BLOTZ

BLOTZ B10-MW-005 Bedienungsanleitung

BLOTZ

BLOTZ B20-MD-019 Bedienungsanleitung

BLOTZ

BLOTZ B10-ME-009 Bedienungsanleitung

BLOTZ

BLOTZ B10-MW-114 Bedienungsanleitung

BLOTZ

BLOTZ B10-ME-010 Bedienungsanleitung

BLOTZ

BLOTZ B15-MC-005 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung