Blueant ENDURE Bedienungsanleitung

ENDURE

USER GUIDE

Read Me to Get the Most Out of

Your Device...

• ENGLISH

• FRANÇAIS

• ESPAÑOL

Endure Quick Start Guide: English

Indicator

Light

Vol -Vol +

Command

Button

Microphones

Model: T2

Charge Your Headset

Your headset has been given an initial partial charge to get started,

but for best results charge it using the supplied USB cable and

adaptor until the indicator light turns white.

> Charge the Endure whenever it announces the battery is Very Low.

> Your headset features Rapid Charge technology. It will charge to

50% capacity in just 30 minutes. A full charge takes about 2 hours.

> During charging, the indicator light ﬂashes red.

> When the light goes white, the charge is complete.

> The Endure features an iPhone headset battery meter so you can

check your battery status at a glance.

USB Connector

(lift cover to access)

Power

Switch

Wearing the Endure

You can wear your

headset on either ear.

For best results:

> Position the hook

and ear gel as

shown here.

> Make sure the

headset is angled

towards your mouth.

Pair Your Headset

1. Slide the power switch across to turn the Endure on.

2. Put the Endure in your ear.

3. The ﬁrst time you use the Endure it will go straight to pair mode

and talk you through the pairing process.

For subsequent pairings, make sure the Endure is not connected to

any phones, then hold down the Command button. The Endure will

announce it is going into pairing mode.

Tip: The pairing code is 0000 (four zeros).

LEFT

EAR

RIGHT

EAR

Pairing mode will time out after 2 minutes. To go back into pairing

mode, press and hold the Command button. To cancel pairing mode,

turn the Endure off and back on again.

Transfer Your Phonebook

Once the pairing is complete, your headset will attempt to transfer

your phonebook contacts so that it can announce the names of

incoming callers. Please accept any connection requests on your

phone from the Endure and wait for the transfer to ﬁnish.

Some phones do not support automatic phonebook transfers. If

the Endure announces that this is the case, you need to go to your

phone’s address book and send contacts via Bluetooth to the Endure.

See “Phonebook Troubleshooting” or www.blueantwireless.com

for help.

Note: Whenever you add contacts to your phone in future you must

update your phonebook on the Endure: with the headset connected

to your phone but not on a call, hold down the Command button for 3

seconds to initiate a phonebook update.

Making Calls

Voice Dialing

To use this feature your phone must support voice dialing over

Bluetooth.

1. Double click the Command button.

2. The Endure activates your phone’s voice dial feature (if available).

Once you have activated the voice dial feature, you are using your

phone’s voice recognition software. Please check your phone manual

to ﬁnd out what commands your phone supports.

> On the iPhone 4S this command activates Siri. There’s no need to

touch or unlock your phone. Note: Siri must be enabled on your

phone. Go to Settings > General on your iPhone and check that Siri

is set to ON.

> Android™ users: use this command to activate Google Voice

Actions (if available). Note: Depending on your handset, you may

need to disable the phone password lock to use voice dialing over

Bluetooth. Check your phone manual for further information on

this feature.

Other Ways To Make Calls

> Dial the number on your phone. The audio automatically transfers

to the headset.

> Hold down Vol + for 1 second to redial the last outgoing call.

> Hold down Vol - for 1 second to call back the last incoming call.

Taking Calls

When the phone rings, you can answer with your voice: wait for the

prompt to ask you if you want to take the call, and then say Answer

or Ignore.

If you don’t want to wait for the prompt, or you are in a noisy place:

> Click the Command button once to accept the call.

> Double click the Command button to reject the call.

During a call, click the Command button to end the call.

Multipoint

Up to 2 phones can connect to the Endure at the same time. To pair

a second phone:

1. Use your phone’s Bluetooth menu to disconnect the existing paired

phone from the Endure.

2. With the Endure switched on, hold down the Command button until

the Endure starts to talk you through the pairing process.

3. When the pairing is complete, use the Bluetooth menu on each

phone to reconnect them to the Endure.

When you have 2 phones connected, you can always answer a call

on either phone. If you initiate a call through the Endure, or activate

phone voice dialing, it will happen on the “primary phone”: the one

that connected to the headset ﬁrst.

Listening to Audio

The Endure supports A2DP audio streaming: if your phone or

Bluetooth device supports the A2DP proﬁle then simply start playing

music or any other audio (including directions from a GPS application

on the phone) and it will automatically transfer to the headset.

The audio will mute automatically if you make or receive a phone call,

and resume when the call ends.

Note: The Endure only supports A2DP bluetooth audio streaming

from one phone at a time.

Reset your Endure

If you are having problems with the Endure, you can reset it and start

again:

1. Disconnect the Endure from your phone by deleting the pairing

from your phone’s Bluetooth menu.

2. Turn your phone off and back on again to clear its memory.

3. With the Endure switched on, but not connected to any phones,

hold down all three buttons (Vol +, Vol -, and the Command button)

for about 3 seconds.

The Endure will reset and go straight to pairing mode. You will now

need to pair your phone with the Endure again.

Free Android Application

> Reads your incoming text messages

> Helps with pairing and setup

Go to the Android Market and search for “BlueAnt” to download and

install this free application. Once the application is installed you will

hear your text messages read aloud automatically on your BlueAnt

device as they come in.

Supports Android handsets running Android version 2.1 or above.

Android is a trademark of Google, Inc, and its use is subject to its

permissions.

Scan this code on your

phone with a QR code

reader to download the

application:

Phonebook Troubleshooting

When you pair your phone the Endure attempts to transfer the

contacts from your phonebook so that it can announce the names of

incoming callers.

Note: If your phone prompts you to allow a connection to the Endure,

you must select “YES” or “OK”.

Android™

On Android devices a message about the

phonebook transfer may appear in the

notiﬁcations area at the top of the screen.

In order to transfer your contacts you must

swipe your ﬁnger over this message and

accept the phonebook transfer request from

the Endure.

If you miss this step you will need to:

1. Delete the pairing from your phone.

2. Power the phone off and back on.

3. Reset your Endure and pair it with your phone again.

This is due to the way the Android PBAP request system works.

12a Phonebook Access Request

Notiﬁcation

shown on

Android

devices

Andere Handbücher für ENDURE

Inhaltsverzeichnis

Sprachen:

Andere Blueant Headset Handbücher

Blueant

Blueant BLUEANT Z9 Installationsanleitung

Blueant

Blueant interphone F4 stereo Bedienungsanleitung

Blueant

Blueant X3 MICRO Bedienungsanleitung

Blueant

Blueant V12 Installationsanleitung

Blueant

Blueant T1 Bedienungsanleitung

Blueant

Blueant Z9i Bedienungsanleitung

Blueant

Blueant ENDURE Bedienungsanleitung

Blueant

Blueant Q3 Bedienungsanleitung

Blueant

Blueant Q2 Bedienungsanleitung

Blueant

Blueant Q1 Bedienungsanleitung

Blueant

Blueant CT Bedienungsanleitung

Blueant

Blueant X5 Bedienungsanleitung

Blueant

Blueant T8 micro Bedienungsanleitung

Blueant

Blueant BLUEANT Z9 Bedienungsanleitung

Blueant

Blueant Z9i Bedienungsanleitung

Blueant

Blueant X3 MICRO Bedienungsanleitung

Blueant

Blueant T2 ENDURE Bedienungsanleitung

Blueant

Blueant V1 Bedienungsanleitung

Blueant

Blueant interphone F4 stereo Bedienungsanleitung

Blueant

Blueant Q2 Bedienungsanleitung

Blueant

Blueant SuperTooth II Installationsanleitung

Blueant

Blueant X5i Bedienungsanleitung

Blueant

Blueant SuperTooth II Bedienungsanleitung

Blueant

Blueant SuperTooth II Bedienungsanleitung

Beliebte Headset Handbücher anderer Marken

Sena

Sena SMH10 Bedienungsanleitung

IASUS

IASUS Stealth IA-NT4-BASIC-BT Bedienungsanleitung

Sennheiser

Sennheiser EPOS ADAPT 230 Bedienungsanleitung

Doro

Doro Flexus HS2005 Bedienungsanleitung

GE 98971 Bedienungsanleitung

Hama

Hama 00184070 Bedienungsanleitung

Plantronics

Plantronics Blackwire 3200 Series Bedienungsanleitung

Blue Tiger

Blue Tiger Advantage PLUS Bedienungsanleitung

Jawbone

Jawbone Icon Bedienungsanleitung

Jabra

Jabra FR 20 Bedienungsanleitung

Roxcore

Roxcore Flow A+ Bedienungsanleitung

Turtle Beach

Turtle Beach XP 510 Bedienungsanleitung

Philips

Philips SHB6101 Bedienungsanleitung

Jabra

Jabra PRO 9460 Duo Bedienungsanleitung

HyperX

HyperX HyperX Cloud Flight Bedienungsanleitung

Bose

Bose MIE2 Mobile Bedienungsanleitung

Jabra

Jabra Steel Bedienungsanleitung

HyperX

HyperX cloud ii Bedienungsanleitung