Blueant T2 ENDURE Bedienungsanleitung

T2 ENDURE

USER GUIDE

Read Me to Get the Most Out of

Your Device...

T2_User_Guide_EN.indd 1

2/2/2012 7:19:42 PM

T2 Endure Quick Start Guide: English

Indicator

Light

Vol -Vol +

Command

Button

Microphones

Charge Your Headset

Your headset has been given an initial partial charge to get started,

but for best results charge it using the supplied USB cable and

adaptor until the indicator light turns white.

Charge the T2 whenever it announces that the battery is Very Low.

Your headset features Rapid Charge technology. It will charge to

50% capacity in just 30 minutes. A full charge takes about 2 hours.

During charging, the indicator light ﬂashes red.

When the light goes white, the charge is complete.

The T2 features an iPhone headset battery meter so you can check

your battery status at a glance.

USB Connector

(lift cover to access)

Power

Switch

T2_User_Guide_EN.indd 2

2/2/2012 7:19:42 PM

T2 Endure Quick Start Guide: English

Indicator

Light

Vol -Vol +

Command

Button

Microphones

Charge Your Headset

Your headset has been given an initial partial charge to get started,

but for best results charge it using the supplied USB cable and

adaptor until the indicator light turns white.

> Charge the T2 whenever it announces that the battery is Very Low.

> Your headset features Rapid Charge technology. It will charge to

50% capacity in just 30 minutes. A full charge takes about 2 hours.

> During charging, the indicator light ﬂashes red.

> When the light goes white, the charge is complete.

> The T2 features an iPhone headset battery meter so you can check

your battery status at a glance.

USB Connector

(lift cover to access)

Power

Switch

T2_User_Guide_EN.indd 3

2/2/2012 7:19:42 PM

Wearing the T2

You can wear your

headset on either ear.

For best results:

> Position the hook

and ear gel as

shown here.

> Make sure the T2

is angled towards

your mouth.

Pair Your Headset

1. Slide the power switch across to turn the T2 on.

2. Put the T2 in your ear.

3. The ﬁrst time you use the T2 it will go straight to pair mode and

talk you through the pairing process.

For subsequent pairings, make sure the T2 is not connected to any

phones, then hold down the Command button. The T2 will

announce it is going into pairing mode.

Tip: The pairing code is 0000 (four zeros).

LEFT

EAR

RIGHT

EAR

Transfer Your Phonebook

Once the pairing is complete, your headset will attempt to transfer

your phonebook contacts so that it can announce the names of

incoming callers. Please accept any connection requests on your

phone from the T2 and wait for the transfer to ﬁnish.

Some phones do not support automatic phonebook transfers. If the

T2 announces that this is the case, you need to go to your phone’s

address book and send contacts via Bluetooth to the T2.

See “Phonebook Troubleshooting” or www.blueantwireless.com

for help.

Note: Whenever you add contacts to your phone in future you must

update your phonebook on the T2: with the T2 connected to your

phone but not on a call, hold down the Command button for 3

seconds to initiate a phonebook update.

Voice Commands

To use one of the voice commands, click the Command button, wait

for the T2 to ask you to Say A Command, then say the command:

Check Battery — Tells you the current headset battery level.

Phone Commands — Activates your phone’s voice dialing feature (if

T2_User_Guide_EN.indd 4

2/2/2012 7:19:42 PM

Wearing the T2

You can wear your

headset on either ear.

For best results:

> Position the hook

and ear gel as

shown here.

> Make sure the T2

is angled towards

your mouth.

Pair Your Headset

1. Slide the power switch across to turn the T2 on.

2. Put the T2 in your ear.

3. The ﬁrst time you use the T2 it will go straight to pair mode and

talk you through the pairing process.

For subsequent pairings, make sure the T2 is not connected to any

phones, then hold down the Command button. The T2 will

announce it is going into pairing mode.

Tip: The pairing code is 0000 (four zeros).

LEFT

EAR

RIGHT

EAR

Transfer Your Phonebook

Once the pairing is complete, your headset will attempt to transfer

your phonebook contacts so that it can announce the names of

incoming callers. Please accept any connection requests on your

phone from the T2 and wait for the transfer to ﬁnish.

Some phones do not support automatic phonebook transfers. If the

T2 announces that this is the case, you need to go to your phone’s

address book and send contacts via Bluetooth to the T2.

See “Phonebook Troubleshooting” or www.blueantwireless.com

for help.

Note: Whenever you add contacts to your phone in future you must

update your phonebook on the T2: with the T2 connected to your

phone but not on a call, hold down the Command button for 3

seconds to initiate a phonebook update.

Voice Commands

To use one of the voice commands, click the Command button, wait

for the T2 to ask you to Say A Command, then say the command:

> Check Battery — Tells you the current headset battery level.

> Phone Commands — Activates your phone’s voice dialing feature (if

T2_User_Guide_EN.indd 5

2/2/2012 7:19:42 PM

available on your phone). Depending on your phone model, you may

need to record voice tags on the phone to use this feature.

On the iPhone 4S this command activates Siri.

On Android devices this command activates Google Voice Actions.

Voice recognition will cancel automatically after a short period

of time if you do not say a command. You can also cancel voice

recognition by clicking the Command button.

Making Calls

Voice Dialing

To use this feature your phone must support voice dialing over

Bluetooth.

1. Double click the Command button or use the Phone Commands

voice command.

2. The T2 activates your phone’s voice dial feature (if available).

Once you have activated the voice dial feature, Voice Dialing uses your

phone’s voice recognition software.

Tip: On the iPhone 4S this command activates Siri. There’s no need to

touch or unlock your phone.

Android™ users: use this command to activate Google Voice Actions

(if available).

Please check your phone manual to ﬁnd out what voice commands

your phone supports.

Other Ways To Make Calls

Dial the number on your phone. The audio automatically transfers

to the headset.

Hold down Vol + for 1 second to redial the last outgoing call.

Hold down Vol - for 1 second to call back the last incoming call.

Taking Calls

When the phone rings, you can answer with your voice: wait for the

prompt to ask you if you want to take the call, and then say Answer

Ignore.

If you don’t want to wait for the prompt, or you are in a noisy place:

Click the Command button once to accept the call.

Double click the Command button to reject the call.

During a call, click the Command button to end the call.

T2_User_Guide_EN.indd 6

2/2/2012 7:19:42 PM

available on your phone). Depending on your phone model, you may

need to record voice tags on the phone to use this feature.

On the iPhone 4S this command activates Siri.

On Android devices this command activates Google Voice Actions.

Voice recognition will cancel automatically after a short period

of time if you do not say a command. You can also cancel voice

recognition by clicking the Command button.

Making Calls

Voice Dialing

To use this feature your phone must support voice dialing over

Bluetooth.

1. Double click the Command button or use the Phone Commands

voice command.

2. The T2 activates your phone’s voice dial feature (if available).

Once you have activated the voice dial feature, Voice Dialing uses your

phone’s voice recognition software.

Tip: On the iPhone 4S this command activates Siri. There’s no need to

touch or unlock your phone.

Android™ users: use this command to activate Google Voice Actions

(if available).

Please check your phone manual to ﬁnd out what voice commands

your phone supports.

Other Ways To Make Calls

> Dial the number on your phone. The audio automatically transfers

to the headset.

> Hold down Vol + for 1 second to redial the last outgoing call.

> Hold down Vol - for 1 second to call back the last incoming call.

Taking Calls

When the phone rings, you can answer with your voice: wait for the

prompt to ask you if you want to take the call, and then say Answer

or Ignore.

If you don’t want to wait for the prompt, or you are in a noisy place:

> Click the Command button once to accept the call.

> Double click the Command button to reject the call.

During a call, click the Command button to end the call.

T2_User_Guide_EN.indd 7

2/2/2012 7:19:42 PM

Multipoint

Up to 2 phones can connect to the T2 at the same time. To pair a

second phone:

1. Use your phone’s Bluetooth menu to disconnect the existing paired

phone from the T2.

2. With the T2 switched on, hold down the Command button until the

T2 starts to talk you through the pairing process.

3. When the pairing is complete, use the Bluetooth menu on each

phone to reconnect them to the T2.

When you have 2 phones connected, you can always answer a call on

either phone. If you initiate a call through the T2, or activate phone

voice dialing, it will happen on the “primary phone”: the one that

connected to the T2 ﬁrst.

Listening to Audio

The T2 supports A2DP audio streaming: if your phone or Bluetooth

device supports the A2DP proﬁle then you can simply start playing

music or any other audio (including directions from a GPS application

on the phone) and it will automatically transfer to the headset.

The audio will mute automatically if you make or receive a phone call,

and resume when the call ends.

Note: The T2 only supports A2DP bluetooth audio streaming from the

primary phone.

Reset your T2

If you are having problems with the T2, you can reset it and start

again:

Disconnect the T2 from your phone by deleting the pairing from

your phone’s Bluetooth menu.

Turn your phone off and back on again to clear its memory.

With the T2 switched on, but not connected to any phones, hold

down all three buttons (Vol +, Vol -, and the Command button) for

about 3 seconds.

The T2 will reset and go straight to pairing mode. You will now need

to pair your phone with the T2 again.

T2_User_Guide_EN.indd 8

2/2/2012 7:19:42 PM

Multipoint

Up to 2 phones can connect to the T2 at the same time. To pair a

second phone:

1. Use your phone’s Bluetooth menu to disconnect the existing paired

phone from the T2.

2. With the T2 switched on, hold down the Command button until the

T2 starts to talk you through the pairing process.

3. When the pairing is complete, use the Bluetooth menu on each

phone to reconnect them to the T2.

When you have 2 phones connected, you can always answer a call on

either phone. If you initiate a call through the T2, or activate phone

voice dialing, it will happen on the “primary phone”: the one that

connected to the T2 ﬁrst.

Listening to Audio

The T2 supports A2DP audio streaming: if your phone or Bluetooth

device supports the A2DP proﬁle then you can simply start playing

music or any other audio (including directions from a GPS application

on the phone) and it will automatically transfer to the headset.

The audio will mute automatically if you make or receive a phone call,

and resume when the call ends.

Note: The T2 only supports A2DP bluetooth audio streaming from the

primary phone.

Reset your T2

If you are having problems with the T2, you can reset it and start

again:

1. Disconnect the T2 from your phone by deleting the pairing from

your phone’s Bluetooth menu.

2. Turn your phone off and back on again to clear its memory.

3. With the T2 switched on, but not connected to any phones, hold

down all three buttons (Vol +, Vol -, and the Command button) for

about 3 seconds.

The T2 will reset and go straight to pairing mode. You will now need

to pair your phone with the T2 again.

T2_User_Guide_EN.indd 9

2/2/2012 7:19:42 PM

Free Android Application

> Reads your incoming text messages

> Helps with pairing and setup

Go to the Android Market and search for “BlueAnt” to download and

install this free application. Once the application is installed you will

hear your text messages read aloud automatically on your BlueAnt

device as they come in.

Supports Android handsets running Android version 2.1 or above.

Android is a trademark of Google, Inc, and its use is subject to its

permissions.

Scan this code on your

phone with a QR code

reader to download the

application:

Phonebook Troubleshooting

When you pair your phone the T2 attempts to transfer the contacts

from your phonebook so that it can announce the names of incoming

callers.

Note: If your phone prompts you to allow a connection to the T2, you

must select “YES” or “OK”.

Android™

On Android devices a message about the

phonebook transfer may appear in the

notiﬁcations area at the top of the screen.

In order to transfer your contacts you must

swipe your ﬁnger over this message and

accept the phonebook transfer request from

the T2.

If you miss this step you will need to:

Delete the T2 pairing from your phone.

Power the phone off and back on.

Reset your T2 and pair it with your phone again.

This is due to the way the Android PBAP request system works.

13a

Phonebook Access Request

Notiﬁcation

shown on

Android

devices

T2_User_Guide_EN.indd 10

2/2/2012 7:19:42 PM

Andere Handbücher für T2 ENDURE

Inhaltsverzeichnis

Sprachen:

Andere Blueant Headset Handbücher

Blueant

Blueant interphone F4 stereo Bedienungsanleitung

Blueant

Blueant Q2 Bedienungsanleitung

Blueant

Blueant Q3 Bedienungsanleitung

Blueant

Blueant Z9i Kurzanleitung

Blueant

Blueant V12 Bedienungsanleitung

Blueant

Blueant X3 MICRO Bedienungsanleitung

Blueant

Blueant ENDURE Bedienungsanleitung

Blueant

Blueant ENDURE Bedienungsanleitung

Blueant

Blueant X5i Bedienungsanleitung

Blueant

Blueant CT Bedienungsanleitung

Blueant

Blueant V1 Bedienungsanleitung

Blueant

Blueant Q2 Bedienungsanleitung

Blueant

Blueant Interphone none Installationsanleitung

Blueant

Blueant V1 Bedienungsanleitung

Blueant

Blueant T8 micro Bedienungsanleitung

Blueant

Blueant Z9i Bedienungsanleitung

Blueant

Blueant BLUEANT Z9 Bedienungsanleitung

Blueant

Blueant X3 MICRO Bedienungsanleitung

Blueant

Blueant X3 MICRO Installationsanleitung

Blueant

Blueant Interphone none Bedienungsanleitung

Blueant

Blueant interphone F4 stereo Bedienungsanleitung

Blueant

Blueant Q2 Bedienungsanleitung

Blueant

Blueant V1 Bedienungsanleitung

Blueant

Blueant SuperTooth II Installationsanleitung

Beliebte Headset Handbücher anderer Marken

Sena

Sena SMH10 Bedienungsanleitung

IASUS

IASUS Stealth IA-NT4-BASIC-BT Bedienungsanleitung

Sennheiser

Sennheiser EPOS ADAPT 230 Bedienungsanleitung

Doro

Doro Flexus HS2005 Bedienungsanleitung

GE 98971 Bedienungsanleitung

Hama

Hama 00184070 Bedienungsanleitung

Plantronics

Plantronics Blackwire 3200 Series Bedienungsanleitung

Blue Tiger

Blue Tiger Advantage PLUS Bedienungsanleitung

Jawbone

Jawbone Icon Bedienungsanleitung

Jabra

Jabra FR 20 Bedienungsanleitung

Roxcore

Roxcore Flow A+ Bedienungsanleitung

Turtle Beach

Turtle Beach XP 510 Bedienungsanleitung

Philips

Philips SHB6101 Bedienungsanleitung

Jabra

Jabra PRO 9460 Duo Bedienungsanleitung

HyperX

HyperX HyperX Cloud Flight Bedienungsanleitung

Bose

Bose MIE2 Mobile Bedienungsanleitung

Jabra

Jabra Steel Bedienungsanleitung

HyperX

HyperX cloud ii Bedienungsanleitung