BMI AutoMagic Bedienungsanleitung

1 1

Manual

BMI –AutoMagic

Automatic crossline- plus 5 dot - laser

(

pulsed laser lines for the use of receiver)

Content

1. Introduction page 2

2. Laser Safety page 2

3. Power supply page 3

4. Startup operation and function display page 3

4.1 Activate page 4

4.2 Selection of laser lines / laser-dots page 4

4.3 Deactivate page 4

5. Accuracy check page 5

5.1 Checking accuracy of horizontal laser line and laser dots

pointing right, l left and forward page 5

5.2 Checking accuracy of horizontal laser line page 6

5.3 Checking accuracy of 90° - angles between laser beams page 7

5.4 Checking the rectitude of the horizontal laser lines page 8

5.5 Checking accuracy of the plumb beams page 9

6. Technical data page 10

2 2

1. Introduction

The BMI –AutoMagic is a fully automatic, self leveling

Crosslines- and 5 - points –laser.

The BMI –AutoMagic can be used for Indoor- and outdoor area.

The device has to be kept dry.

( Protection class IP 54).

CAUTION: Never insert the device into water!

Note that the usage of the BMI –AutoMagic under humid and wet

weather conditions may affect the measurements due to the water

drops on the laser.

The device has to be under dry conditions when returned back to its

transport case.

2. Laser safety

The BMI –AutoMagic has the Laser category class 2 M / EN 60825-1:2007

with a wavelength of 630 to 670 nm and max. output von ≤ 1 mW.

Safety instructions

DO NOT REMOVE THE WARNING SIGN OF LASER DEVICE SIE

DO NOT STARE DIRECTLY INTO THE LASER BEAM

DO NOT AIM AT ANY OTHER PERSON WITH THE LASER EVEN OUT

OF A LONG DISATNCE

DO NOT INSTALL THE LASER WITHIN THE EYE LEVEL!

DO NOT OPEN THE DIVCE

If the device is opened by any unauthorized person, the liability of the manufacturer

or dealer will expire immediately for any accruing damages.

3 3

3. Power supply

The BMI –AutoMagic runs on customary batteries.

(4 pcs, 1,5 V LR6 / AA).

Red LED above the activation button starts to blink when the batteries are on low

capacity and should be replaced.

To change the batteries, open

the battery cover, take off

the used batteries and replace them.

Mind the polarity

4. Start up operation and function display

Button 1

ON / OFF

Selection button

Slide

Pendulum-transport

safety lock

ON / OFF

Control-LED

Pendulum

transport-safety

Battery-Capacity

Control-LED

pulsed Lines

Button 2

pulsed Lines

On / Off

4 4

4.1 Activate the BMI –AutoMagic

Button 1 ON / OFF - Press shortly

Shift the slide of the Pendulum –Transport lock to the right

The device levels out automatically. The Cross lines of the laser will be illustrated.

Red LED above the On / Off –button is on, when the pendulum-transport lock is

not disengaged. The laser lines blink slowly.

The self-leveling mode is not activated!

Red LED above the ON / OFF–button blinks, when the batteries are running on

low capacity and need to be replaced

. If the automatic leveling function is not possible, e.g. because

the surface on which the measuring tool stands deviates

by more than 4° from the horizontal plane, the laser beams flash slowly

If the laser is used for inclinations, the slide of the pendulum- transport lock has to

be shifted to the left in order to lock the pendulum. The self-leveling is

deactivated! The laser lines will blink slowly and the LED above the ON / OFF –

button is on.

The pulsed laser lines allow the use and work with the receiver –ex. Outdoor

In order to work with the receiver, press button 2 shortly. The pulse mode is now

activated and verified by the blue LED above the button 2. To terminate the pulse

mode repress the button 2.

4.2 Selection of the requested laser lines / laser-dots

Button 1 - Press 1 x

Horizontal line is on.

Button 1 - Press 2 x

Vertical line is on.

Button 1 - Press 3 x

All 5 –laser dots are on.

Button 1 - Press 4 x

Laser cross lines and the 5 laser dots will be on.

4.3 Deactivate the BMI –AutoMagic

Button 1 ON/OFF press long, the laser light will go off.

Shift the slide of the pendulum transport lock safety to the left.

5 5

Abbildung 2

5. Accuracy Check

Before the activation, a drop or a hit we recommend to run a check up

of the device; otherwise the manufacturer’s liability is expired.

5.1 Checking accuracy of the horizontal laser line and laser dots pointing

right, left and forward

Mount the device on the multi-functional adapter.

Select 2 walls in a distance of a minimum of 5m from each other.

(1) Place the device with a distance of ca. 10 cm in front of Wall 2.

(2) Disengage the transport lock, press button 1. The device levels out automatically.

(3) Mark the intersection of horizontal and vertical lines of the cross line (Marking pointA)

(4) Turn the device around 180° without changing the height. (picture 1)

Mark the intersection of the cross line (Marking point B).

(5) Put the device with a distance of ca. 10 cm in front of Wall 2. Mark intersection of

horizontal and vertical lines of the cross line (Marking point B)

(6) Turn the device around 180° without changing the height.

Mark the intersection of the cross line (Marking point A1) ( picture 2)

(7) Messen Sie den Abstand zwischen „A“ und „A1“.

If the marking points A and A1 are identical, the device is conform:

Fläche 1

Picture 2

Wall 1

Wall 2

Section of measurements „S“ 5 m

picture 1

wall 2

wall 1

6 6

Section of

measurement

„S“

Max. tolerable

Distance A –A1

5 m

2 mm

10 m

4 mm

15 m

6 mm

20 m

8 mm

5.2 Checking the accuracy of the vertical laser line

(1) Select a door frame of at least a 2.5 m open space on side of the door (picture 3).

(2) Place the device with a 2.5 m distance from the middle of door frame on point A.

(3) Disengage the transport safety lock, press button 1. The device levels out

automatically.

(4) Mark the point „B“centered underneath the door frame.

(5) Mark a point „C“ within a 5 m distance from point „A“.

(6) Mark a point „D“within the door lintel.

(7) Place the device on the point „C“ and set up the Laser line exact on the point „B“ .

(8) Measure now the gap the laser line from the marked point „D“within the door lintel.

If the gap is less than 1 mm, the device is conform and respects the tolerances.

5.3 Checking 90° angles between laser beams

Picture 3

7 7

Picture 4

Mount the device on the multi-functional adapter.

(1) Set up the device in the middle of an approx. 6x6 m room (picture 4). Switch all laser

lines

(Button 1 press 4x)

(2) Let the laser level itself ,then mark the intersection of laser lines A and all dots

( B, C, D and E)

(3) Turn device about 90° around plumb axis of dot E, until the laser dot C is on the mark

D. Mark the points A´, B´ und D´.

(4) Measure the distance between A –Dˊ, B –Aˊund C –B´

If all deviations are less than 2 mm, the device is conform and respects the

tolerances

8 8

Wall 1

Picture 5

5.4 Checking the accuracy of horizontal laser line

Mount the device on the multi-functional adapter and on a tripod

(1) Set up the device in the middle of an approx. 6x6 m room (picture 4). Switch all

laser lines (Button 1 press 4x)

(2) Mark directly the laser line front intersection point with A on wall 1

(3) Turn the device around in 90°steps, mark each of horizontal laser dots (D,E,F) and

both ends of horizontal laser line ( B,C) near point A. Name them B, C, D, E,F.

(4) Measure distance between the highest and lowest marking point

If the gap is less them 3 mm, the device is conform and respects the

tolerances

9 9

Picture 6

5.5 Checking accuracies of plumb beams (up and down)

Mount the device on the multi-functional adapter and on a tripod

(1) Set up the device on a tripod 1m above ground in a room of 2,5m height

(picture 6).

Turn on the plumb line (button 1, press 3x)

(2) Mark the laser point on the ground with A, the point on the ceiling with B

(3) Turn the device on the tripod by 180°, move tripod until plumb down points directly on

point A again. Now name the new point position at ceiling B1

(4) Now name the new point position at ceiling B1

(5) Measure the distance between point B und B1

If the gap is less them 1 mm, the device is conform and respects the tolerances

1,5 m

1 m

10 10

6. Technical Data of the BMI –autoMAGIC

Laser type: red diode laser, wavelength 630 bis 670 nm

Output: ≤1 mW; Laser class 2 M (EN 60825-1)

Levelling range: ± 4°

Accuracy horizontal/vertical: ± 3 mm / 10 m

Plumb beam, up: ± 2 mm auf 10 m

Plumb beam, down: ± 2 mm auf 10 m

Laser range: up to 30 m depending on brightness

Range with receiver: up to 55 m

Operating range: -10° to +50° C

Storage temperature: -25° to +70° C

Power supply: 4 x 1,5 V LR6 / type AA

Service time: ca. 16 hrs.

Protective system: IP54

Tripod connection size device: 1/4 “and 5/8 “

Tripod connection size adapter: 1/4" and 5/8”

Inhaltsverzeichnis

Andere BMI Messgerät Handbücher

BMI

BMI 19825 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung