BMW 71 60 0 009 711 Bedienungsanleitung

DO IT RIGHT THE FIRST TIME, ON TIME, EVERY TIME 

Installation Instruction P/N 01 29 2 154 664

2008 BMW of North America, LLC

Installation Instructions Page 1 of 13

May 2009

Equipment Parts, Trailer Hitch Ver 2.0 Accessory

Development

These Installation Instructions supersede all previous versions.

SUBJECT

TRAILER HITCH KIT (US Only) - P/N 71 60 0 009 711

MODEL

X5 (E53): Select Vehicle Production 10/99 – 8/06

SUGGESTED INSTALLATION TIME: 2.5 HOURS**

Total installation time may vary depending on vehicle options and equipment.

The instructions below are developed for BMW vehicles and are not to be compared to any other existing

instructions for vehicles other than BMW. No methods other than those specified in this document are to be used

for installation in BMW vehicles. Left and right are determined from the driver’s seat.

Carefully read all instructions and supplements before proceeding with the installation. Reference should be

made to TIS for instructions dealing with a stock part of the vehicle but not stated in detail in these instructions.

The instructions were complete and up to date at time of publication; however, changes to the vehicle or

installation may have occurred. Please report any problems or changes noted with the installation to BMW

Technical Hotline, along with VIN, date of manufacture and as much detail as possible.

Note: BMW NA does not supply or have an approved electrical brake controller for this Trailer

Hitch (Tow Bar) Kit.

Installation Instruction P/N 01 29 2 154 664

PARTS INFORMATION

Contents of Kit - P/N 71 60 0 009 711

Ref. Description Qty BMW Part Number

A Basic tow bar 1 N/A

B Left support 1 N/A

C Right support 1 N/A

D Bumper carrier 1 N/A

E Bumper bracket 2 N/A

F Hexagon bolt M10x30 -10.9 6 N/A

G Hexagon bolt M10x85 -10.9 2 N/A

H Hexagon bolt M10x40 -10.9 4 N/A

I Hexagon bolt M10x120 -10.9 4 N/A

J Washer 10.5x25x3 8 N/A

K Nut M10 with rolled-on washer 8 N/A

L Adhesive label (ball position) 1 N/A

M Electrical socket bracket 1 N/A

N Wiring harness with electrical socket, 7-pin 1 N/A

O Trailer Module AHM II 1 N/A

P Hexagon bolt M6x16 2 N/A

Q Half-round bolt M5x15 4 N/A

R Washer 6.6x14x1.5 2 N/A

S Adhesive label (warning) 1 N/A

T Cable ties, long 1 N/A

U Cable ties, short 3 N/A

V 7-way to 4-way adapter 1 N/A

Installation Instruction P/N 01 29 2 154 664

Vehicle Preparation

1. Disconnect battery.

2. Fold up floor cover.

3. Remove spare wheel.

4. Remove luggage compartment trim on right

and left side. Reference TIS 51 47 172.

5. Remove luggage compartment trim on rear

panel. Reference TIS 51 47 101.

6. Remove rear bumper. Reference TIS 51 12

000.

7. Remove carefully LH and RH mufflers,

reference TIS 18 00 018 and heat shields to

gain access to mounting holes in vehicle

body.

8. Remove metallic impact absorbers (The

metallic impact absorbers are no longer

required with the tow bar mounted).

Installation Instruction P/N 01 29 2 154 664

Wiring

1. Remove the spare wheel bracket/air

suspension pump (1) by removing the four

bolts (2).

2. Remove the plastic electrical box cover plate

(1) by removing the three Phillips head

screws (2).

3. Remove plastic carrier plate (1) by removing

the three Phillips head screws (2 & 3).

4. Clip the trailer module (1) onto the carrier

plate (2).

5. Locate the 15-pin black connector (X609),

and attach to the trailer module (1).

Installation Instruction P/N 01 29 2 154 664

6. Remove plug from hole (1) in rear of body.

7. Secure trailer connector (1) to trailer wiring

harness (2). Engage locking tab (3) into

connector housing.

8. Route the wiring harness (1) through the hole

in the body (2). Install rubber grommet (3)

into body.

9. Inside the tire well, route the harness (1)

along the vehicle wiring harness. Connect

trailer wiring harness connector (2) to 12-pin

connector X393S.

10. Secure harness to existing harness with

cable ties (3).

Installation Instruction P/N 01 29 2 154 664

Crossmember Installation

1. Mount the left and right support (1) through

the opening in the body for the metallic

impact absorber (a). Repeat this step for

both left, and right sides.

Note: The support brackets are position

specific. The locating pin on each

bracket must be in the lower inward

position.

2. Install the supports (1) with the bolts

M10x85 (2) and 10.5x25x3 washers (3),

and the bolts M10x30 (4) and 10.5x25x3

washers (3) hand tight.

3. Install M10x30 bolts (2) and 10.5x25x3

washers (2) to the welded nuts on the

vehicle beneath the bracket (2) on the left

and right hand sides of the luggage

compartment, hand tight.

4. Position basic portion of the crossmember

(1) onto the supports installed in step 1.

Installation Instruction P/N 01 29 2 154 664

5. Install two M10x40 bolts (1) into the basic

part of the tow bar (2). Repeat this step for

left and right sides.

6. Install two M10x120 bolts (2) into the left

and right bumper bracket (1). Position

each bumper bracket on the tow bar with

the protruding end of the center tube facing

down. Repeat this step for the left and right

sides.

7. Tighten all bolts for hitch crossmember, and

support brackets inside, as well as beneath

the vehicle body in steps 2, 3, 5, & 6 to

55Nm.

8. Secure crossmember bolts by bending the

cages over the bolt heads with a punch,

and hammer (1).

9. Secure bumper bracket bolts to the

crossmember by bending the cages over

the bolt heads with a punch, and hammer

(1).

Installation Instruction P/N 01 29 2 154 664

10. Secure the trailer harness connector

bracket (1) with the M6x16 bolts, and

washers (2).

11. Secure 7-pin trailer connector (1) to bracket

with four Phillips head screws (2)

Installation Instruction P/N 01 29 2 154 664

Bumper Preparation

1. Remove the bumper carrier from the bumper.

(Old bumper carrier is no longer required with

the trailer hitch mounted).

2. Secure the supplied bumper carrier to the

bumper cover.

3. Reinstall bumper cover/carrier assembly on

vehicle. Secure with original Torx screws (1)

are now screwed through the tow bar bumper

brackets. (Tightening torque: 55Nm).

4. Reinstall heat shields and rear mufflers.

5. Apply the adhesive label (ball position) over

the receiver tube on the painted surface of

the bumper (clean application area

beforehand).

Important: The ball mount used should

not exceed the dimensions as shown.

Installation Instruction P/N 01 29 2 154 664

6. Apply the adhesive label (white “capacities”

label) over the receiver tube on the painted

surface of the bumper (clean application area

beforehand).

7. Apply the adhesive label (white “no electric

brake” label) on the painted surface of the

bumper as shown. (clean application area

beforehand)

Installation Complete

Inhaltsverzeichnis

Andere BMW Autozubehör Handbücher

BMW

BMW 1 Series Bedienungsanleitung

BMW

BMW 84 64 0 301 448 Bedienungsanleitung

BMW

BMW F23 Soft Top Technology Bedienungsanleitung

BMW

BMW AG/ICOM Bedienungsanleitung

BMW

BMW Wallbox Bedienungsanleitung

BMW

BMW 84 64 0 398 229 Bedienungsanleitung

BMW

BMW Profil 2000 Service-Handbuch

BMW

BMW 5 Series Saloon Bedienungsanleitung

BMW

BMW E39 Bedienungsanleitung

BMW

BMW 84 64 0 153 493 Bedienungsanleitung

BMW

BMW Apollo Bedienungsanleitung

BMW

BMW 65 50 0 418 002 Bedienungsanleitung

BMW

BMW 84 63 0 143 192 Bedienungsanleitung

BMW

BMW Wireless Charging Station Universal Bedienungsanleitung

BMW

BMW B84 02 03 Bedienungsanleitung

BMW

BMW Advanced Car Eye Bedienungsanleitung

BMW

BMW E38 Bedienungsanleitung

BMW

BMW F30 Installationsanleitung

BMW

BMW E65 Bedienungsanleitung

BMW

BMW AccessPORT Bedienungsanleitung

BMW

BMW 01 29 9 416 497 Bedienungsanleitung

BMW

BMW E38 Bedienungsanleitung

BMW

BMW 54 13 086 Bedienungsanleitung

BMW

BMW 84 64 0 025 819 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung