Bosch MGM8642BIN Bedienungsanleitung

new device on

MyBosch now and

get free beneﬁts:

bosch-home.com/

welcome

MGM8642BIN

Mixer Grinder

[en] Instruction manual Mixer Grinder 2

Motor coupler

Speed

selector knob

Rubber feet

Big jar Medium jar Chutney jar

Main unit PoundingBlade

Active flow breaker

Spatula / Tool for fitting

and removing blades

Blender jar with

MaxxJuice extractor

(fruit filter)

Note:

Fitting jar: Place the jar on the top socket of the main unit, ensuring that the

locks fit properly in the jar locking grooves of the top socket.

Jar Lid: Ensure that the lid gasket is properly fitted. Place the lid on top of the

jar, gently press down and lock the lid onto the jar using the lid lock

clamps. Hold the lid gently while operating.

Speed control: Turn the speed selector knob clockwise for speed 1, 2 or 3, as

desired.

Pulse: Turn the speed selector knob anti-clockwise for a few seconds and

release for momentary operation. Pulse is especially useful for

applications such as grinding chutneys, crushing ice, etc.

Overview

Blender jar

Blender jar lid

Blender jar lid stopper

Blender jar blade

Medium jar

Medium jar lid

Medium jar lid stopper

Dry grinding blade

PoundingBlade

Big jar

Big jar lid

Big jar lid stopper

Wet grinding blade

Chutney jar

Chutney jar blade

Chutney jar lid

Chutney jar lid stopper

Big jar Medium jar

Chutney jar Blender jar

en Safety and important instructions

Safety and important instructions

Read and follow the instruction manual carefully and keep for later reference! Enclose

these instructions when you give this appliance to someone else. If the instructions for

correct use of the appliance are not observed, the manufacturer’s liability for any resulting

damage will be excluded.

1. This mixer grinder is strictly for household use and not applicable for non-domestic and/

or commercial use.

2. Please only use official Bosch parts and accessories with the Mixer Grinder. Never use

these parts and accessories with any other appliances.

3. Check if the voltage indicated on the base of the mixer grinder corresponds to the local

electrical mains voltage before you connect the appliance.

4. This appliance can be used by persons with reduced physical, sensory or mental

capabilities or lack of experience and/or knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe manner and if they understand

the hazards involved.

5. Keep children away from the appliance and connecting cable and do not allow them

to use the appliance. Do not let children play with the appliance. Cleaning and user

maintenance must not be performed by children.

6. Do not use the mixer grinder if the power cord and/or appliance are damaged. Only our

customer service may repair the appliance, e.g. by replacing a damaged power cord, in

order to avoid hazards.

7. Do not use the mixer grinder on a wet surface.

8. Keep the mixer grinder away from hot gas burners, electric hot plates or similar appliances.

9. The power cord must not come into contact with hot parts or be pulled across sharp edges.

10. Always ensure that speed selector knob is in the OFF position and the appliance

unplugged before you remove or attach jars or accessories.

11. Blades should be fitted properly before running the mixer grinder.

12. Do not operate the mixer grinder without locking the dome or lid in place or with an empty jar.

13. Always unplug the mixer grinder before reaching into the jar with your fingers or any

other object (such as a spatula).

14. Do not open the lid or dome when the mixer grinder is running.

15. Do not add solid ingredients when the mixer grinder is running.

16. Do not grind hot ingredients or sugar in the mixer grinder.

17. Do not overload the mixer grinder.

18. Do not leave the main unit unattended while in operation.

19. Always unplug the mixer grinder after use, or whenever the appliance is unsupervised

or in the event of an error.

20. In dry grinding, the jar may become hot due to friction. This is quite normal and has

nothing to do with the motor. The jar will cool down with time. If the motor is getting too

hot and you can feel hot air coming out of the side vent or bottom, switch off the mixer

grinder and restart after 10 minutes.

21. Do not run the mixer grinder for more than 5 minutes continuously. Wait for 2 minutes if

you need to use it for longer.

22. Never immerse the main unit in water or any other liquid. Do not rinse or wash in a

dishwasher.

23. Handle the blades carefully, wash them under running water and do not rub with your

hands.

24. It is normal for the mixer grinder to become a little discoloured, especially when used

with ingredients like turmeric. To avoid this, make sure that the ingredients do not come

into contact with the mixer grinder body.

Safety and important instructions

Congratulations on the purchase of

your new Bosch TrueMixx Pro Mixer

Grinder. In doing so, you have opted

for a modern, high-quality domestic

appliance. You can find further

information about our products on our

web page.

Know your mixer grinder

Voltage and frequency 230 V AC, 50 Hz

Class of motor insulation winding wire F class

Rating 30 minutes rating

5 min ON and 2 min OFF (Maximum 6 ON cycles)

Material of body ABS

Material of jars Stainless steel

Blade assembly Stainless steel

Speed control 3 speed with pulse

Main cord PVC flexible 2-core cord

Country of origin India

Normal load Normal load in terms of recipe for 750 W Rating –

200 g Urad Daal soaked in 450 ml water for

12 hours

Jar capacity

Jar Size Rated Capacity

Dry Wet Liquidise

Big jar 1.5 litre - 0.75 litre 1.0 litre

Medium jar 1.0 litre 0.5 litre - -

Chutney jar 0.4 litre 0.2 litre 0.2 litre -

Blender jar 1.5 litre - - 1.0 litre

Minimum capacity for all the above jars is at least up to blade level.

Contents

Overview.....................................................2

Safety and important instructions ...............4

Know your mixer grinder.............................5

Jar capacity ................................................5

Using the product .......................................6

Safety systems ...........................................7

Operating your mixer grinder......................7

Cleaning ....................................................8

Troubleshooting..........................................8

Blade changing procedure .........................9

Blade selection .........................................10

Dry grinding applications with

PoundingBlade ......................................... 11

25. Do not drop the main unit or jars.

26. Do not use the jars as storage containers.

en Using the product

3. How to fit/remove active flow breaker

Your Bosch TrueMixx Mixer Grinder

has an active flow breaker which

improves the quality of your wet grinding

applications. To fit the active flow

breaker, insert the active flow breaker

in the groove on the inside surface

of the big jar and slide it in until it fits

properly. To remove it, gently press in

the opposite direction till it disengages.

Slide it out thereafter.

remove

fit fit

4. How to use MaxxJuice extractor

For mixing smoothies use the blender

jar with the blender jar blade. Put the

MaxxJuice extractor in the blender jar as

shown and press it gently down.

Safety systems

The Bosch TrueMixx Pro Mixer Grinder

is fitted with an overload protector (OFF)

mechanism to prevent the motor burning

out due to overloading. In case of excess

loading with ingredients in the jar, very thick

paste or low voltage conditions, your Bosch

mixer grinder automatically switches off and

the red knob on the bottom of the mixer

grinder will spring out.

Using the product

1. How to fit/remove blades

(big jar, medium jar, blender jar)

Hold the coupler on the underside of

the jar and with the spatula, tighten by

rotating in an anti-clockwise direction

to fit and clockwise to remove until the

blade is securely locked/removed.

remove

fit

Note: If the coupler and/or some other

parts are removed during removing

the blade, please refer to X“Blade

changing procedure” see page 9.

2. How to fit jar to main unit

Carefully insert the jar on top of the

main unit. Ensure that the lock of the jar

fits into the slot of the main unit. Rotate

the jar clockwise until it locks and use

the handle to lock.

Operating your mixer grinder

If this happens, switch off your mixer

grinder and remove the excess ingredients.

Add sufficient water if dealing with thick

paste and wait for 2-3 minutes. Press the

red reset button and start the mixer grinder

again.

Operating your mixer

grinder

Before using for the first time /

using after a long time

Before using the mixer grinder for the

first time or using it after a long time,

thoroughly clean all the parts that come

into contact with food ingredients.

Rotate the motor shaft by hand via the

motor coupler, on top of the main unit.

The motor shaft should rotate freely.

Check that the speed selector is in the

OFF position.

Place the main unit on a smooth, stable

and clean surface.

W Caution!

Never place plastic, paper or cloth under

the mixer grinder as it may block the

ventilation holes.

Connect the main plug to the wall

socket. Your Mixer Grinder has a

dummy 3rd pin on the plug to ensure

stable fixing onto the plug point. Switch

on the main supply and turn the speed

selector knob to the required position

and speed. After operation, turn the

speed selector knob to the OFF position

and check. Repeat until the desired

results are obtained.

You may observe some minor oil

spillage in the Jars and Jar sockets

during first two to three operations. This

is normal. Thoroughly clean the minor

oil spillages with water and wipe dry with

soft cloth.

Preparation of ingredients

Important!

Cool down any hot ingredients before

putting in the jar.

Cut large ingredients into small pieces

approx. 2 cm in size before mixing/

grinding.

Regular use and operation

For blending/liquidising/puréeing use

‘Pulse’ on the speed selector knob. This

will activate Pulse until you release the

button. Use position 1-3 for continuous

operation.

1 = Lowest operating speed

3 = Highest operating speed

Hold down the jar lid gently while your

mixer grinder is in operation.

After switching off the mixer grinder, wait

until the blade stops rotating completely

and only then remove the lid or insert

the spatula.

0/off 1

Before removing the jar from the main

unit, ensure that the power supply is

disconnected.

Avoid using your hand to fill or clean

jars. It is safer and more hygienic to use

the spatula.

Avoid storing food in the jar.

en Cleaning

Cleaning

W Risk of electric shock!

Never immerse the main unit in water or

any other liquid or pour any liquid over it.

Never hold under running water and do not

clean in the dishwasher.

To keep your Bosch mixer grinder sparkling

clean, just follow these steps.

1. First remove the mains plug from the

electrical socket.

2. Clean the main unit using a damp/wet

cloth. Do not use abrasive cleaning

agents.

3. Hold the jar under running water for a

minute after each use to remove the

residue.

4. Please remove active flow breaker while

cleaning the jar. For instructions how to

remove it, please refer to X“How to fit/

remove active flow breaker” see page 6.

5. Remove the jars after each use and

wash in soapy water. Then rinse with

clean water.

6. Dry the parts thoroughly with a clean

soft cloth.

7. Always keep/store the jars upside down.

8. We recommend you clean your Bosch

mixer grinder immediately after use for

easier removal of residue.

9. Do not immerse the main unit in water

or any other liquid or pour liquid over it.

10. Regularly clean the jars and gaskets

after each use for proper hygiene and

performance of the Mixer Grinder.

11. After every use of the Mixer Grinder,

pour small amounts of hot water into

the jars to remove the leftover or sticky

substances.

Troubleshooting

Trouble Reason Check

Mixer grinder does not

switch on

No power supply. Check mains supply.

Overloading with

ingredients.

Remove some ingredients, process

smaller quantities.

Overload protection

mechanism is activated.

Press the red reset button on the

bottom of the mixer grinder.

Other than above

mentioned.

Call Bosch service centre.

Time taken for mixing/

blending is very long

Loose blade or wrong

blade selection.

Check blade and choose blade as

per grinding requirements. Tighten

properly with spatula/spanner.

Overloading of mixer. Remove some ingredients, process

smaller quantities.

Unit overheating External heat source. Check and remove any heat

source, if nearby.

Uneven surface that

blocks air vents.

Place the mixer on a level surface.

Overloading with

ingredients.

Remove some of the ingredients

and add in small quantities.

The coupler and/or some

other parts are removed

during removing the blade.

This is normal and may

happen during changing

the blade.

X“Blade changing procedure” see

page 9.

Blade changing procedure

Parts

Blade (a)

Axis (b)

Coupler (i)

Metal washer (e)

Fibre washer (d)

Fibre washer (c)

Fibre washer (f)

Fibre washer (g)

Metal washer (h)

Removing the blade

1. Hold the coupler on the underside of the

jar and using spatula rotate the blade

nut in a clockwise direction.

remove

2. If the coupler is removed (the blade

sticks together with the axis), washers

will come off when you take blade

assembly out of the jar.

W Small parts – be careful not to lose or

forget them.

3. Take the blade assembly out of the jar.

4. Hold the blade assembly with cloth.

Using spatula untighten the blade nut

(turn in a clockwise direction).

remove

en Blade selection

Fitting the blade

Do this in reverse order as described

in Chapter “Removing the blade” (see

page 9).

5. Put selected blade onto the axis and

tighten the blade nut with the spatula

(rotate in anti-clockwise direction).

6. Put 2 x fibre- and metal washer onto the

axis. Put the assembly into the jar.

7. Put 2 x fibre- and metal washer onto the

axis from the underside and tighten the

coupler by rotating it in an anti-clockwise

direction.

new picture

will be made

8. Check that all parts are properly

connected before use.

fit

Blade selection

Your Bosch TrueMixx Pro Mixer Grinder comes with a special PoundingBlade. Use this

blade to prepare dry grinding applications for a perfect authentic taste.

Blade Jar Application

PoundingBlade Medium Sambhar masala, garam masala, rasam

powder, puliyodharai masala, idli podi

Dry grinding blade Medium Turmeric, coriander seeds, black pepper,

cumin, red chilli powder, almonds, rice

powder

Wet grinding blade Big Idli batter, dosa batter, tomato purée

Chutney blade Chutney Ginger garlic paste, coconut chutney,

coriander chutney

Blender jar blade Blender Chickoo milk shake, banana milk shake,

soya milk, pomegranate juice, water

melon juice, orange/sweet lime juice etc.

Inhaltsverzeichnis

Andere Bosch Schleifer Handbücher

Bosch

Bosch 2 608 000 684 Bedienungsanleitung

Bosch

Bosch PSM 10,8 LI Bedienungsanleitung

Bosch

Bosch Professional GWS 5-100 Bedienungsanleitung

Bosch

Bosch PWS 720-125 Bedienungsanleitung

Bosch

Bosch GWS 13-125 CI Professional Bedienungsanleitung

Bosch

Bosch Professional GWS 2000 Bedienungsanleitung

Bosch

Bosch Professional GWS 12-125 S Bedienungsanleitung

Bosch

Bosch GWC Professional 9-115 Bedienungsanleitung

Bosch

Bosch GWS 26-230 JH Bedienungsanleitung

Bosch

Bosch GWS 20-230 JH Bedienungsanleitung

Bosch

Bosch GWS 14,4 V PROFESSIONAL Bedienungsanleitung

Bosch

Bosch 1364 - 15 Amp Hand Held Abrasive Cutoff... Bedienungsanleitung

Bosch

Bosch GWS 18-125 V-LI Bedienungsanleitung

Bosch

Bosch DG250C Montageanleitung

Bosch

Bosch Professional GWS 30-180 B Bedienungsanleitung

Bosch

Bosch GGS Professional 28 CE Bedienungsanleitung

Bosch

Bosch GEX 150 TURBO Professional Bedienungsanleitung

Bosch

Bosch GWS 12-125 CI Professional Bedienungsanleitung

Bosch

Bosch Professional GWS 18V-10 C Bedienungsanleitung

Bosch

Bosch Professional GWS 18V-10 P Bedienungsanleitung

Bosch

Bosch MGM6632.IN Bedienungsanleitung

Bosch

Bosch Professional GWS 18V-7 Bedienungsanleitung

Bosch

Bosch AG40-85 Montageanleitung

Bosch

Bosch PWS 9-125 CE Bedienungsanleitung

Beliebte Schleifer Handbücher anderer Marken

Parkside

Parkside PWS 230 C3 Bedienungsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Technisches Handbuch

PTA

PTA P1322 Bedienungsanleitung

Crown

Crown CT13313 Bedienungsanleitung

Parkside

Parkside 280250 Bedienungsanleitung

Climax

Climax VM2150 Series Bedienungsanleitung

Jet

Jet JPSG-618M1 Service-Handbuch

Makita

Makita GA4030 Bedienungsanleitung

DeWalt

DeWalt DWEN202 Bedienungsanleitung

Grizzly

Grizzly G2790 Bedienungsanleitung

Fein

Fein MSf843-1a Bedienungsanleitung

RAMSET

RAMSET CBAGR18 Bedienungsanleitung

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Bedienungsanleitung

MW TOOLS

MW TOOLS ME15W Bedienungsanleitung

Caravaggi

Caravaggi SP 20 Betriebsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Technisches Handbuch

Metabo

Metabo WEF 9-125 Quick Bedienungsanleitung

FujiFilm

FujiFilm FA-67-8F Bedienungsanleitung