Bosch GLM100-23 Montageanleitung

IMPORTANT: IMPORTANT: IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento

y seguridad

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

For English Version Version française Versión en español

See page 4 Voir page 23 Ver la página 43

GLM100-23

Call Toll Free for Consumer Information & Service Locations

Pour obtenir des informations et les adresses de nos centers de

service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y

ubicaciones de servicio

160992A6EZ GLM100-23 202210.indd 1 10/4/22 10:19 AM

-2-

abc

160992A6EZ GLM100-23 202210.indd 2 10/4/22 10:19 AM

-3-

1’ 6” (0.5m)

8’ (2.45m)

1’ 6” (0.5m)

160992A6EZ GLM100-23 202210.indd 3 10/4/22 10:19 AM

-4-

General Safety Rules

Read all instructions. Failure to

follow all instructions listedbelow

may result in hazardous radiation exposure, electric

shock, fire and/or serious injury. The term “tool” in the

warnings listed belowrefers toyour mains-operated(corded)

tool or battery-operated (cordless) tool.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The following label is

on your laser tool for

your safety. ALWAYS BE

AWARE of their location

when using the tool.

Safety Symbols

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

Read manual symbol - Alerts user to read

manual.

WARNING indicates a hazardous

situation which, if not avoided, will result in death or

serious injury.

160992A6EZ GLM100-23 202210.indd 4 10/4/22 10:19 AM

-5-

Working safely with the measuring tool is possible only when

the operating and safety information are read completely and

the instructions contained therin are strictly followed. Never

make warning labels on the Measuring tool unrecognizable.

Never aim the beam at a workpiece with a reflective surface.

Bright shiny reflective sheet steel or similar reflective surfaces

are not recommended for laser use. Reflective surfaces could

direct the beam back towards the operator.

Take care to recognize the accuracy and range of the device.

Measurement may not be accurate if used beyond the rated range

of the device.

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

The use of optical instruments with this product will increase

eye hazards.

Do not point the laser beam at persons or animals and do not

look intothe laserbeam yourself, not even from alarge distance.

General Safety Rules

DO NOT direct the laser beam at persons or

animalsanddo notstareintothelaserbeam

yourself. This laser measure produces

class 2 laser radiation and complies with

21 CFR 1040.10 and 1040.11 except for

conformance with IEC 60825-1 Ed. 3., as described in

Laser Notice No. 56, dated May 8, 2019.” This can lead to

persons being blinded.

Safety Rules

160992A6EZ GLM100-23 202210.indd 5 10/4/22 10:19 AM

-6-

Do not use the laser viewing glasses as safety goggles. The laser

viewing glasses are used for improved visualization of the laser

beam, but they do not protect against laser radiation.

Do not use the laser viewing glasses as sun glasses or in traffic.

The laser viewing glasses do not afford complete UV protection and

reduce color perception.

ALWAYS: Make sure that any bystanders in the vicinity of use

are made aware of the dangers of looking directly into the

measuring tool.

DO NOT remove or deface any warning or caution labels.

Removing labels increases the risk of exposure to laser

radiation.

DO NOT stare directly at the laser beam or project the laser

beam directly into the eyes of others. Serious eye injury could

result.

DO NOT place the measuring tool in a position that may

cause anyone to stare into the laser beam intentionally or

unintentionally. Serious eye injury could result.

DO NOT use any optical tools such as, but not limited to,

telescopes or transits to view the laser beam. Serious eye injury

could result.

ALWAYS remove the batteries when cleaning the laser light

aperture to laser lens.

DO NOT operate the measuring tool around children or allow

children to operate the measuring tool. Serious eye injury could

result.

ALWAYS turn the measuring tool “OFF” when not in use.

Leaving the measuring tool “ON” increases the risk of someone

inadvertently staring into the laser beam.

Safe Operating Procedures

160992A6EZ GLM100-23 202210.indd 6 10/4/22 10:19 AM

-7-

DO NOT operate the measuring tool in combustible areas such

as in the presence of flammable liquids, gases or dust.

ALWAYS position the measuring tool securely. Damage to the

measuring tool and/or serious injury to the user could result if the

measuring tool falls.

ALWAYS use only the accessories that are recommended by

the manufacturer of your measuring tool. Use of accessories

that have been designed for use with other measuring tools could

result in serious injury.

DO NOT leave measuring tool “on” unattended in any

operation mode.

Repair and servicing must always be performed by a qualified

repair facility. Repairs performed by unqualified personnel could

result in serious injury.

DO NOT use this measuring tool for any purpose other than

those outlined in this manual. This could result in serious injury.

DO NOT disassemble the measuring tool. There are no user

serviceable parts inside. Disassembling the laser will void all

warranties on the product. Do not modify the product in any

way. Modifying the measuring tool may result in hazardous laser

radiation exposure.

Electrical safety

Batteries can explode or leak, cause injury or fire. To reduce

this risk, always follow all instructions and warnings on the

battery label and package.

DO NOT short any battery terminals.

DO NOT charge alkaline batteries.

DO NOT mix old and new batteries. Replace all of them at the

same time with new batteries of the same brand and type.

DO NOT mix battery chemistries.

Dispose of or recycle batteries per local code.

DO NOT dispose of batteries in fire.

Keep batteries out of reach of children.

Remove batteries if the device will not be used for several

months.

160992A6EZ GLM100-23 202210.indd 7 10/4/22 10:19 AM

-8-

The manufacturer is not responsible for radio

interference caused by unauthorized modiﬁca-

tions to this equipment. Such modiﬁcations

could void the user’s authority to operate the

equipment.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

1) This device may not cause harmful interfer-

ence, and

2) This device must accept any interference

received, including interference that may

cause undesired operation.

NOTE! This equipment has been tested and

found to comply with the limits for a Class

B digital devices, pursuant to Part 15 of the

FCC rules. These limits are designed to pro-

vide reasonable protection against harmful

interference in a residential installation. This

equipment generates uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio com-

munications. However, there is no guarantee

that interference will not occur in a particu-

lar installation. If this equipment does cause

harmful interference to radio or television re-

ception, which can be determined by turning

the equipment oﬀ and on, the user is encour-

aged to try to correct the interference by one

or more of the following measures:

•Reorientorrelocatethereceivingantenna.

FCC Caution

160992A6EZ GLM100-23 202210.indd 8 10/4/22 10:19 AM

-9-

•Increasetheseparationbetweentheequip-

ment and receiver.

•Connect the equipment into an outlet on a

circuit diﬀerent from that to which the re-

ceiver is connected.

•Consultthedealeroranexperiencedradio/

TV technician for help.

IC Canada

This class B digita device complies with ICES-003

CanadaICES-003(B)/NMB-003(B)

160992A6EZ GLM100-23 202210.indd 9 10/4/22 10:19 AM

-10-

Features

The numbering of the product features shown refers to the

illustration of the measuring tool on the graphic page.

1On/Off

(Measuring button)

2Display

3Battery lid

4Latch of battery lid

5Serial number

6Laser warning label

7Reception lens

8Laser beam outlet

9Rounding button

10 Rear edge

Display Elements

aBattery status indicator

bLaser on indicator

cFractional rounding

dCurrent measuring value

eProduct name

fProduct information

gManual QR code

hFactory reset

iLegal notes

The measuring tool is intended for measuring distances,

lengths, heights and clearances. The measuring tool is

suitable for measuring only indoors.

Intended Use

160992A6EZ GLM100-23 202210.indd 10 10/4/22 10:19 AM

Inhaltsverzeichnis

Sprachen:

Andere Bosch Messgerät Handbücher

Bosch

Bosch DLE 40 Professional Bedienungsanleitung

Bosch

Bosch BEA 060 Bedienungsanleitung

Bosch

Bosch CH-48027 Bedienungsanleitung

Bosch

Bosch PTD 1 Bedienungsanleitung

Bosch

Bosch GLM 50 Professional Bedienungsanleitung

Bosch

Bosch GLM 100 C Professional Bedienungsanleitung

Bosch

Bosch GLM 30 Professional Bedienungsanleitung

Bosch

Bosch Rexroth VDP 92.1 Bedienungsanleitung

Bosch

Bosch AdvancedLevel 360 Bedienungsanleitung

Bosch

Bosch CDR 900 Bedienungsanleitung

Bosch

Bosch PLR 50 Bedienungsanleitung

Bosch

Bosch PLL 1 P Bedienungsanleitung

Bosch

Bosch DLE 150 Connect Bedienungsanleitung

Bosch

Bosch BEA 060 Bedienungsanleitung

Bosch

Bosch Professional LR 45 Bedienungsanleitung

Bosch

Bosch GRL Professional 250 HV Bedienungsanleitung

Bosch

Bosch HND 300 Bedienungsanleitung

Bosch

Bosch DAF220 Bedienungsanleitung

Bosch

Bosch GCL 2-15 Professional Bedienungsanleitung

Bosch

Bosch Professional GCL 2-50 Bedienungsanleitung

Bosch

Bosch PTD 1 Bedienungsanleitung

Bosch

Bosch BEA 055 Bedienungsanleitung

Bosch

Bosch GCL 25 Professional Bedienungsanleitung

Bosch

Bosch GIM 120 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung