Bosch GLM165-10 Montageanleitung

IMPORTANT:

Read Before Using

IMPORTANT :

Lire avant usage

IMPORTANTE:

Leer antes de usar

For English Version

See page 4

Version française

Voir page 19

Versión en español

Ver la página 36

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

GLM165-10

Call Toll Free for Consumer Information and Service Locations

Pour obtenir des informations et les adresses de nos centers de service

après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y

ubicaciones de servicio

2610047291 90x145.indd 1

4/7/17 10:12 AM

2610047291 90x145.indd 2

4/7/17 10:12 AM

1'6"

2610047291 90x145.indd 3

4/7/17 10:12 AM

General Safety Rules

Safety Symbols

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Read manual symbol - Alerts user to read manual.

WARNING indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

DO NOT operate the laser tool around children or allow chil-

dren to operate the laser tool. Serious eye injury could result.

DO NOT use measuring tools, attachments and accessories

outdoors when lightening conditions are present.

Read all instructions. Failure to follow all

instructions listed below may result in

hazardous radiation exposure, electric shock, fire and/or

serious injury. The term “tool” in the warnings listed below

refers to your mains-operated (corded) tool or battery-operated

(cordless) tool.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

2610047291 90x145.indd 4

4/7/17 10:12 AM

Electrical safety

Batteries can explode or leak, cause

injury or fire.To reduce this risk, always

follow all instructions and warnings on the battery label

and package.

Do not short any battery terminals.

Do not charge alkaline batteries.

Do not mix old and new batteries. Replace all of them at

the same time with new batteries of the same brand and

type.

Do not mix battery chemistries.

Dispose of or recycle batteries per local code.

Do not dispose of batteries in fire.

Keep batteries out of reach of children.

Remove batteries if the device will not be used for several

months.

Personal safety

Stay alert, watch what you are doing and use common

sense when operating a measuring, detection and layout

tool. Do not use a measuring, detection and layout tool

while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating

measuring, detection and layout tools may result in serious

personal injury or incorrect measurement results.

Use safety equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate conditions will

reduce personal injuries.

DO NOT use any optical tools such as, but not limited to,

telescopes or transits to view the laser beam. Serious eye

injury could result.

DO NOT stare directly at the laser beam or project the laser

beam directly into the eyes of others. Serious eye injury

could result.

Use caution when using measuring tools in the vicinity of

electrical hazards.

2610047291 90x145.indd 5

4/7/17 10:12 AM

Measuring, detection and layout tool use and

care

Use the correct measuring, detection and layout tool for

your application. The correct measuring, detection and layout

tool will do the job better and safer at the rate for which it was

designed.

Do not use the measuring, detection and layout tool if the

switch does not turn it on and off. Any measuring, detection

and layout tool that cannot be controlled with the switch is dan-

gerous and must be repaired.

Store idle measuring, detection and layout tools out of the

reach of children and do not allow persons unfamiliar with

the measuring, detection and layout tool or these instruc-

tions to operate the measuring, detection and layout tool.

Measuring, detection and layout tools may be dangerous in the

hands of untrained users.

Maintain measuring, detection and layout tools. Check for

misalignment or binding of moving parts, breakage of parts

and any other condition that may affect the measuring, de-

tection and layout tools operation. If damaged, have the

measuring, detection and layout tool repaired before use.

Many accidents are caused by poorly maintained measuring,

detection and layout tools.

Use the measuring, detection and layout tool, accessories,

etc., in accordance with these instructions and in the man-

ner intended for the particular type of measuring, detection

and layout tool, taking into account the working conditions

and the work to be performed. Use of the measuring, detec-

tion and layout tool for operations different from those intended

could result in a hazardous situation.

Service

Have your measuring, detection and layout tool serviced by

a qualified repair person using only approved replacement

parts. This will ensure that the safety of the measuring, detec-

tion and layout tool is maintained.

Develop a periodic maintenance schedule for your measur-

ing, detection and layout tool. Follow checking and recali-

bration procedures outlined in the instruction manual.

2610047291 90x145.indd 6

4/7/17 10:12 AM

When cleaning a tool be careful not to disassemble any

portion of the tool since internal wires may be misplaced

or pinched or may be improperly mounted. Certain cleaning

agents such as gasoline, carbon tetrachloride, ammonia, etc.

may damage plastic parts.

Safety Rules for Laser Tools

The following label is on your laser tool for your safety. AL-

WAYS BE AWARE of its location when using the tool.

DO NOT direct the laser beam at persons or

animals and do not stare into the laser beam

yourself.This tool produces class 2 laser radia-

tion and complies with 21 CFR 1040.10 and

1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.This can lead to persons

being blinded.

DO NOT place the measuring tool in a position that may

cause anyone to stare into the laser beam intentionally or

unintentionally. Serious eye injury could result.

Never aim the beam at a workpiece with a reflective surface.

Bright shiny reflective sheet steel or similar reflective

surfaces are not recommended for laser use. Reflective

surfaces could direct the beam back towards the operator.

DO NOT operate the measuring tool around children or

allow children to operate the measuring tool. Serious eye

injury could result.

ALWAYS: Make sure that any bystanders in the vicinity of

use are made aware of the dangers of looking directly into

the measuring tool.

DO NOT remove or deface any warning or caution labels.

Removing labels increases the risk of exposure to laser

radiation.

2610047291 90x145.indd 7

4/7/17 10:12 AM

DO NOT operate the measuring tool in combustible areas

such as in the presence of flammable liquids, gases or dust.

Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

Do not use the laser viewing glasses as sun glasses or in

traffic. The laser viewing glasses do not afford complete UV

protection and reduce color perception.

DO NOT leave measuring tool “ON” unattended in any

operation mode.

ALWAYS turn the measuring tool “OFF” when not in use.

Leaving the measuring tool “ON” increases the risk of someone

inadvertently staring into the laser beam.

ALWAYS position the measuring tool securely. Damage to

the measuring tool and/or serious injury to the user could result

if the measuring tool falls.

Take care to recognize the accuracy and range of the

device. Measurement may not be accurate if used beyond the

rated range of the device.

ALWAYS use only the accessories that are recommended

by the manufacturer of your measuring tool. Use of

accessories that have been designed for use with other

measuring tools could result in serious injury.

DO NOT use this measuring tool for any purpose other

than those outlined in this manual. This could result in

serious injury.

ALWAYS remove the batteries when cleaning the laser light

aperture and laser lens.

DO NOT disassemble the measuring tool.There are no user

serviceable parts inside. Disassembling the laser will void

all warranties on the product. Do not modify the product in

any way. Modifying the measuring tool may result in hazardous

laser radiation exposure.

Repair and servicing must always be performed by a

qualified repair facility. Repairs performed by unqualified

personnel could result in serious injury.

2610047291 90x145.indd 8

4/7/17 10:12 AM

Features

The numbering of the product features shown refers to the illustration

of the measuring tool on the graphic page.

1Measuring (On/Off) Button

2 Display

3 Battery lid

4Latch of battery lid

5Serial number

6Laser warning label

7Reception lens

8Laser beam outlet

Display Elements

aTemperature warning

bBattery low indicator

cMeasuring function

Auto-square footage (or

m2) measurement

dLaser switched on

eUnit of measure

fMeasurement value after 1st

press

gMeasurement value after 2nd

press

hAuto-square total

The measuring tool is intended for measuring distances,

lengths, heights and clearances. The measuring tool is

suitable for measuring only indoors.

Intended Use

2610047291 90x145.indd 9

4/7/17 10:12 AM

Digital Laser Measure GLM165-10

Measuring range (typical) 6 in - 165 ft (0.15 –50 mA)

Measuring accuracy (typical) ±1/16 in (±1.5 mmB)

Lowest indication unit 1/32 in (1 mm)

Automatic switch-off after approx.

- Laser 20 s

- Measuring Tool 5 min

Operating temperature +14° F to 113° F (-10° C to +45° C)

Storage temperature -4° F to 158° F (-20° C to +70° C)

Relative air humidity, max. 90 %

Laser class 2

Laser type 635 nm, <1mW

Laser beam diameter at 77° F (25 °C)

- at 30 ft (10 m) distance, approx. 3/8 in (9 mm)

- at 165 ft (50 m) distance, approx. 1-3/4 in (45 mm)

Batteries 2 x 1.5V (AAA)

Battery service life in measuring operation, approx. 5 h

Degree of Protection IP54 (dust and splash water protected)C

Weight 0.2 lb (0.09 kg)

Dimensions 4.1 x 1.6 x 0.9 in (105 x 41 x 24 mm)

A) The working range increases depending on how well the laser light is reflected from

the surface of the target (scattered, not reflective) and with increased brightness of

the laser point to the ambient light intensity (interior spaces, twilight). In unfavorable

conditions, e.g., with extreme interior illumination or a badly reflecting surface, the

measuring range may be limited.

B) In favorable conditions, a deviation influence of ±0.05 mm/m must be taken

into account. In unfavorable conditions, e.g., with extreme illumination, badly

reflecting surface or the room temperature deviating heavily from 77 °F (25 °C),

the maximum deviation can be up to ±3.0mm. Additionally, a deviation influence

of 0.15mm/m must be taken into account.

C) Does not apply to battery compartment.

The measuring tool can be clearly identified with the serial

number 5on the type plate.

Technical Data

2610047291 90x145.indd 10

4/7/17 10:12 AM

Inhaltsverzeichnis

Sprachen:

Andere Bosch Messgerät Handbücher

Bosch

Bosch PMD 10 Bedienungsanleitung

Bosch

Bosch D-tect200C Montageanleitung

Bosch

Bosch DLR165 Montageanleitung

Bosch

Bosch GLM 80 Professional Bedienungsanleitung

Bosch

Bosch TTM 2104 Bedienungsanleitung

Bosch

Bosch Professional GLM 50-23 G Bedienungsanleitung

Bosch

Bosch GCL 2-15 G Professional Bedienungsanleitung

Bosch

Bosch GTL 3 Professional Bedienungsanleitung

Bosch

Bosch PLR 50 Bedienungsanleitung

Bosch

Bosch LR 7 Professional Bedienungsanleitung

Bosch

Bosch Professional GLM 50-23 G Bedienungsanleitung

Bosch

Bosch GCL 2-15 Bedienungsanleitung

Bosch

Bosch GRL4000-80CH Montageanleitung

Bosch

Bosch GLM 20 Bedienungsanleitung

Bosch

Bosch GLL100-40G Montageanleitung

Bosch

Bosch Professional GLM 30-23 Bedienungsanleitung

Bosch

Bosch PLR50 C Bedienungsanleitung

Bosch

Bosch GLM 50 C Professional Bedienungsanleitung

Bosch

Bosch GTL 3 Professional Bedienungsanleitung

Bosch

Bosch BEA 040 Bedienungsanleitung

Bosch

Bosch GLM 30 Professional Bedienungsanleitung

Bosch

Bosch GRL 500 H Bedienungsanleitung

Bosch

Bosch LR40G Montageanleitung

Bosch

Bosch 13.5159.0060 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung