Bosch MBE Series Bedienungsanleitung

MBE Mounts and Adapters

MBE Series

en Installation Guide

MBE Mounts and Adapters Table of Contents | en 3

Bosch Security Systems, Inc. Installation Guide | 3.0 | 2011.10

Table of Contents

1 Important safety instructions 4

2 MBE Series Mounts and Adapters 6

2.1 Unpacking 6

2.2 Parts Lists 7

3 MBE-27/28 Wall Mount Applications 8

3.1 Mounting the MBE-27/28 to a Wall 8

3.2 Mounting the MBE-27/28 with the MBE-17 Wall Adapter 9

4 MBE-27/28 Pole Mount Applications 12

5 Attaching Cameras to the Brackets 15

5.1 Attaching an EX27 to the MBE-27 15

5.2 Attaching a REG-D1/L1 to an MBE-28 17

6 Dimensional Outlines 20

4en | Important safety instructions MBE Mounts and Adapters

| 3.0 | 2011.10 Installation Guide Bosch Security Systems, Inc.

1 Important safety instructions

Type numbers:

DANGER!

High risk: This symbol indicates an imminently hazardous

situation such as “Dangerous Voltage” inside the product.

If not avoided, this will result in an electrical shock, serious

bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily

injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation.

if not avoided, this could result in property damage or risk of

damage to the unit.

MBE Mounts and Adapters Important safety instructions | en 5

Bosch Security Systems, Inc. Installation Guide | 3.0 | 2011.10

Read, follow, and retain all of the following safety instructions.

Heed all warnings on the unit and in the operating instructions

before operation.

1. Clean only with a dry cloth. Do not use liquid cleaners or

aerosol cleaners.

2. Do not install unit near any heat sources such as radiators,

heaters, stoves, or other equipment (including amplifiers)

that produce heat.

3. Adjust only those controls specified in the operating

instructions.

4. Unless qualified, do not attempt to service a damaged unit

yourself. Refer all servicing to qualified service personnel.

5. Use only replacement parts specified by the manufacturer.

6. Install in accordance with the manufacturer's instructions

in accordance with applicable local codes.

7. Use only attachments/accessories specified by the

manufacturer. Equipment change or modification could

void the user's guarantee or authorization agreement.

You can view and print the full version of this Installation

Manual with Adobe Acrobat Reader, available online. This user

guide is the intellectual property of Bosch Security Systems;

protected by copyright. Contact: www.boschsecurity.com

6en | MBE Series Mounts and Adapters MBE Mounts and Adapters

| 3.0 | 2011.10 Installation Guide Bosch Security Systems, Inc.

2 MBE Series Mounts and Adapters

This manual describes the following MBE series mounting

brackets and adapters:

MBE-27B / MBE-27W: a black or white mounting bracket for

use with an EX27 Series All-Weather Camera.

MBE-28B: a black mounting bracket for use with the REG-D1 or

the REG-L1 License Plate Camera.

MBE-15B / MBE-15W: a black or white adapter used to attach

an MBE-27 or MBE-28, along with an EXMB.020B Heavy Duty L

Bracket, to a pole.

This adapter can also accommodate the EXMB.028 Cable

Managed Wall Bracket or the EXMB.023 Wall Bracket.

MBE-17B / MBE-17W: a black or white adapter used to attach

an MBE-27 or an MBE-28, along with an EXMB.020B Heavy Duty

L-Bracket, to a wall.

This adapter can also accommodate the EXMB.028 Cable

Managed Wall Bracket or the EXMB.023 Wall Bracket.

Refer to Section 6 Dimensional Outlines, page 20, for

dimensional drawings of each mount and adapter.

2.1 Unpacking

This equipment should be unpacked and handled with care. If

an item appears to have been damaged in shipment, notify the

shipper immediately.

Verify that all the parts listed in the product's Parts List below

are included. If any items are missing, notify your Bosch

Security Systems Sales or Customer Service Representative.

The original packing carton is the safest container in which to

transport the unit and must be used if returning the unit for

service. Save it for possible future use.

MBE Mounts and Adapters MBE Series Mounts and Adapters | en 7

Bosch Security Systems, Inc. Installation Guide | 3.0 | 2011.10

2.2 Parts Lists

MBE-15B / MBE-15W Pole Mount Adapter

MBE-17B / MBE-17W Wall Mount Adapter

MBE-27B / MBE-27W Wall Mount Bracket

MBE-28B Wall Mount Bracket

Quantity Description

1 Pole mount adapter plate, black or white

2 Metal bands with gear clamps

4 M6 x 20 mm bolts

4 M6 flat washers

Quantity Description

1 Wall mount adapter plate, black or white

4 M6 x 20 mm bolts

4 M6 flat washers

Quantity Description

1 Bracket arm for EX27, black or white

1 #6 Hex Key

1 EX27 interface plate

1 M8 x 45 mm bolt

Quantity Description

1 Bracket arm for REG-D1/REG-L1, black

1 #4 hex key

1 #5 hex key

6 M5 x 10 mm bolts (attached to bracket)

6 M5 plastic captive washers (attached to bracket)

8en | MBE-27/28 Wall Mount Applications MBE Mounts and Adapters

| 3.0 | 2011.10 Installation Guide Bosch Security Systems, Inc.

3 MBE-27/28 Wall Mount Applications

The MBE-27B, MBE-27W, and the MBE-28B Brackets can be

mounted directly to a wall or to the MBE-17 Wall-Mount

Adapter. The MBE-17 Wall-Mount Adapter provides extra

support and can withstand heavier loads.

The MBE-28 Bracket also allows cables to run through the arm

and up the mount head at the end of the arm to connect to the

camera.

For a secure mounting installation, bolts should extend through

the mounting surface and be secured with nuts, washers, and

lock washers on the opposite side.

If studs are used, they should either be anchored in concrete or

welded to a steel backer plate.

3.1 Mounting the MBE-27/28 to a Wall

The MBE-27/28 can be mounted directly to a wall surface and

can support up to 25 kg (55 lbs). Use the MBE-17 wall-mount

adapter if your application requires extra support. Refer to

Section 3.2 Mounting the MBE-27/28 with the MBE-17 Wall

Adapter, page 9.

1. Determine a secure mounting location for the wall

installation.

2. Use the four (4) holes on the flanges of the MBE-27/28

wall-mount bracket as a template to mark the position

where the holes should be drilled to secure the mount.

MBE-28: If routing cables through the wall, drill a 25 mm

(1 in.) hole placed exactly in the middle of the four (4)

marked holes.

CAUTION!

Ensure that the mounting fasteners have a minimum pull-out

strength of 300 kg (661.4 lbs) per screw.

MBE Mounts and Adapters MBE-27/28 Wall Mount Applications | en 9

Bosch Security Systems, Inc. Installation Guide | 3.0 | 2011.10

3. Drill the four (4) holes in the installation location.

4. Using four bolts or studs (not supplied) with nuts,

washers, and lock washers, fasten the MBE-27/28 to its

mounting location and tighten all nuts securely.

Note: The minimum diameter bolt (or stud) required is

6 mm (.25 in.).

3.2 Mounting the MBE-27/28 with the MBE-17

Wall Adapter

The MBE-17 Wall-Mount Adapter provides increased support for

the MBE-27 and the MBE-28 bracket. The MBE-17 also provides

a mounting location for the EXMB.020B L-bracket, a heavy-duty

bracket used to mount an additional piece of equipment, such

as an illuminator.

The combination of the MBE-27/28 and the MBE-17 can support

a total weight of 45 kg (100 lbs).

Note: The MBE-17 Wall-Mount Adapter has two distinct hole

patterns for attaching various mounting brackets. Use the 94.2

x 40 mm (3.71 x 1.57 in.) hole pattern with the MBE-27/28

bracket. (Use the 86 x 40 mm hole pattern with the old

EXMB.023 or EXMB.028 bracket.)

Refer to Section 6 Dimensional Outlines, page 20, for detailed

dimensional drawings.

CAUTION!

Ensure that the mounting fasteners have a minimum pull-out

strength of 300 kg (661.4 lbs) per screw.

NOTICE!

The fasteners and mounting surface must be capable of

supporting a maximum load of 25 kg (55 lbs).

10 en | MBE-27/28 Wall Mount Applications MBE Mounts and Adapters

| 3.0 | 2011.10 Installation Guide Bosch Security Systems, Inc.

1. Determine a secure mounting location for the wall

installation.

2. Use the six (6) holes on the flanges of the MBE-17 wall-

mount adapter as a template to mark the position where

the holes should be drilled to secure the adapter.

MBE-28: If routing cables through the wall, use the center

hole on the MBE-17 as a template to drill through the wall.

3. Drill the six (6) holes in the installation location, bolts not

supplied.

Note: The minimum diameter bolt (or stud) required is

6 mm (.25 in.).

4. Orient the MBE-17 so that the 94.2 x 40.0 mm

(3.71 x 1.57 in.) hole pattern is at the top.

5. Using six bolts (or studs) with nuts, washers, and lock

washers, fasten the MBE-17 to its mounting location and

tighten all nuts securely.

6. Align the four holes on the MBE-27B, MBE-27W, or the

MBE-28B bracket with the 94.2 x 40 mm (3.71 x 1.57 in.)

hole pattern on the MBE-17 adapter.

CAUTION!

Ensure that the mounting fasteners have a minimum pull-out

strength of 300 kg (661.4 lbs) per screw

NOTICE!

The fasteners and mounting surface must be capable of

supporting a maximum load of 45 kg (100 lbs).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bosch Rack & Stand Handbücher

Bosch

Bosch UB-10DB Installations- und Betriebshandbuch

Bosch

Bosch FBH 0000 A Bedienungsanleitung

Bosch

Bosch B12 Bedienungsanleitung

Bosch

Bosch RA1165 Montageanleitung

Bosch

Bosch RM 10 Kurzanleitung

Bosch

Bosch GTA 2600 Professional Bedienungsanleitung

Bosch

Bosch TS1014 Bedienungsanleitung

Bosch

Bosch PTA 2400 Bedienungsanleitung

Bosch

Bosch PTA1000 Bedienungsanleitung

Bosch

Bosch GTA 60 W Professional Bedienungsanleitung

Bosch

Bosch FRK 0019 A Bedienungsanleitung

Bosch

Bosch AutoDome Bedienungsanleitung

Bosch

Bosch 303-435 Bedienungsanleitung

Bosch

Bosch GCR 350 Bedienungsanleitung

Bosch

Bosch GTA 600 Professional Bedienungsanleitung

Bosch

Bosch LTC 9349MK Bedienungsanleitung

Bosch

Bosch TS2000 Montageanleitung

Bosch

Bosch PTA 2400 Bedienungsanleitung

Bosch

Bosch Professional GTA 560 Bedienungsanleitung

Bosch

Bosch T4B Montageanleitung

Bosch

Bosch FLEXIDOME NDA-FMT-MICDOME Bedienungsanleitung

Bosch

Bosch PTA 1 Bedienungsanleitung

Bosch

Bosch B12 Bedienungsanleitung

Bosch

Bosch TS1015 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung