Bosch DX4010V2 Bedienungsanleitung

Installation Instructions

RS-232/USB Serial

Interface Module

DX4010V2

DX4010V2 |Installation Instructions | Trademarks

2 Bosch Security Systems, Inc. | 9/08 | F01U083036-01

Trademarks

•BlackBox® is either a registered trademark or a

trademark of BlackBox Corporation in the United

States and/or other countries.

DX4010V2 |Installation Instructions | Contents

Bosch Security Systems, Inc. | 9/08 | F01U083036-01 3

Contents

1.0 General Information ....................................4

2.0 Specifications ..............................................4

3.0 Installation Standards .................................4

4.0 Wiring........................................................... 5

5.0 DX4010V2 Jumper Pin Settings ................ 6

5.1 Enable LED Jumper Pins (P2) ..................... 6

5.2 DB9 Ground Enable Pins (P1) ..................... 6

5.3 Address DIP Switches.................................. 7

6.0 Remote Programming Direct Connection 7

7.0 DB9 DTE RS-232 Connector (P6) ............ 10

8.0 RJ-16 Data Bus Connector (P3) .............. 11

9.0 USB Data Bus Connector ........................ 11

9.1 Installing USB Drivers ................................ 11

Figures

Figure 1: DX4010V2 Component Layout .............. 4

Figure 2: Control Panel Connections .................... 5

Figure 3: External Power Supply Connections...... 5

Figure 4: Serial Device Connections..................... 5

Figure 5: Parallel Device Connections.................. 6

Figure 6: P2 Jumper Settings ............................... 6

Figure 7: DIP Switch Location and Orientation ..... 7

Figure 8: DB9 Connector Layout ........................ 10

Figure 9: P3 Connector....................................... 11

Figure 10: Select File............................................ 11

Figure 11: Security Warning ................................. 11

Figure 12: Install Shield ........................................ 11

Figure 13: Security Warning ................................. 11

Figure 14: Destination Location ............................ 12

Figure 15: Ready to Install .................................... 12

Figure 16: Setup Status ........................................ 12

Figure 17: Installation Complete ........................... 12

Figure 18: USB Driver Installer ............................. 12

Figure 19: Scanning.............................................. 12

Figure 20: Installation Complete ........................... 12

Figure 21: System Properties ............................... 13

Figure 22: Device Manager................................... 13

Figure 23: Panel Communication.......................... 13

Tables

Table 1: DX4010V2 Specifications ...................... 4

Table 2: Diagnostic LED Functions ..................... 6

Table 3: Option Bus Address DIP Switch Settings8

Table 4: SDI Bus Address DIP Switch Settings ... 9

Table 5: Alternate Wiring Configuration............. 10

DX4010V2 |Installation Instructions | 1.0 General Information

4 Bosch Security Systems, Inc. | 9/08 | F01U083036-01

1.0 General Information

The DX4010V2 is a data terminal equipment (DTE)

configured RS-232/USB serial device interface. This

module is designed to operate with compatible control

panels. It connects to the control panel through the

Option or SDI data bus.

The DX4010V2 is used to connect a PC with RPS,

BIS, PC 9000, CMS 7000, or other third party

software that uses a serial connection to the

supported control panels. The module also supports a

serial printer (or parallel printer with a converter box)

for control panels that support a serial printer. The

compatibility lists in Table 1 show support information.

2.0 Specifications

Table 1: DX4010V2 Specifications

Operating

Voltage

12 VDC nominal

Current Draw 55 mA nominal, 60 mA with

diagnostic LEDs enabled

Communication

Configuration

Programmable through the control

panel. Refer to the appropriate

control panel programming

instructions.

The baud rate for the printer output on a

DS7400Xi must be greater than 300 baud.

Operating

Temperature

0°C to +50°C (+32°F to +122°F)

Relative

Humidity

5 to 85% @ +30°C (+86°F)

non-condensing

Control Panel

Compatibility

Option bus control panels: D6412,

D4412, DS7240, DS7220, DS7400Xi

(v2.02 or higher)

SDI bus control panels (v6.0 or

higher): D9412GV2, D7412GV2,

D7212GV2, D9412G, D7412G,

D7212G, D9124, D9112, D7412, and

D7212

Table 1: DX4010V2 Specifications (continued)

Application

Compatibility

RPS: Supported on all compatible

control panels.

PC 9000: Supported on SDI Bus

control panels (D9412G, D7412G,

D7212G, D9112, D7412, and D7212).

BIS: Supported on SDI Bus control

panels, v6.3 and higher (D9412GV2,

D7412GV2, D7212GV2, D9412G,

D7412G, and D7212G).

CMS 7000: Supported on DS7400Xi

Control Panels set at Mode 18 (v3.09

or higher).

Printers: Supported on compatible

control panel.

Figure 1: DX4010V2 Component Layout

SER

RxTx

BUS

RxTx

LED

DB9 GND

ENABLE

1- DB9 GND enable pins (P1)

2- RJ-16 data bus connector (P3)

3- Data bus (TS1)

4- Address DIP switches (S1)

5- Diagnostic LEDs

6- Diagnostic LED enable pins (P2)

7- USB Connector (P7)

8- DB9 DTE RS-232 connector (P6)

3.0 Installation Procedure

Failure to follow the instructions in this

manual can result in personal injury or

damage to the equipment.

The DX4010V2 contains static-sensitive

components and must be handled with

care. Follow anti-static procedures when

handling the modules.

Test according to NFPA 72 if used in fire

applications.

DX4010V2 |Installation Instructions | 4.0 Wiring

Bosch Security Systems, Inc. | 9/08 | F01U083036-01 5

1. Disconnect power to the control panel by

unplugging the transformer and removing the red

battery lead.

2. Remove screws from enclosure cover to access

the DX4010V2 board.

3. Connect circuit wiring and install jumper pins.

Refer to Section 4.0 Wiring on page 5.

4. Replace enclosure cover.

5. Connect a serial cable to the serial device. Refer

to Section 7.0 DB9 DTE RS-232 Connector (P6)

on page 10.

6. Reapply power to the control panel.

4.0 Wiring

Remove all power to the control panel (AC

and standby battery) before making or

breaking any connections. Failure to do so

can result in personal injury or damage to

the equipment.

Wire Length Restrictions

•0.8 mm (#22 AWG): 305 m (1000 ft)

•1.2 mm (#18 AWG): 610 m (2000 ft)

•USB or Serial Cables are not to exceed 2 meters

(6 ft) in length.

SDI option bus wiring is limited to 305 m

(1000 ft).

Connect the DX4010V2 to the control panel data and

auxiliary power sources as shown in Figure 2.

Figure 2: Control Panel Connections

1- DX4010V2 data bus

2- Control panel data bus

3- Option AUX common/SDI common (black)

4- Option data/SDI B (green)

5- Option data/SDI A (yellow)

6- Option AUX power +/SDI power (red)

If an external 12 VDC power supply is used, wire as

shown in Figure 3.

Figure 3: External Power Supply Connections

1- DX4010V2 data bus

2- Control panel data bus

3- Option AUX common/SDI common (black)

4- Option data/SDI B (green)

5- Option data/SDI A (yellow)

6- Option AUX power +/SDI power (red)

7- External 12 VDC power supply

Figure 4 shows serial device-to-DX4010V2

connections using the DB9 DTE RS-232 connector

(P6).

Figure 4: Serial Device Connections

SER

RxTx

BUS

RxTx

LED

DB9 GND

ENABLE

1- Serial (RS-232) device such as a PC (with

RPS, BIS, PC9000, or other third party

application) or a serial printer for supported

control panels.

Refer to Section 7.0 DB9 DTE RS-232

Connector (P6) on page 10 for additional

information.

DX4010V2 |Installation Instructions | 5.0 DX4010V2 Jumper Pin Settings

6 Bosch Security Systems, Inc. | 9/08 | F01U083036-01

Figure 5 shows a parallel printer connected to the

serial output of the DX4010V2. This type of

connection requires the use of a serial to parallel

converter, such as the BlackBox PI045A serial to

Centronics parallel converter cable. The cable is

available from BlackBox® (www.blackbox.com).

Figure 5: Parallel Device Connections

SER

RxTx

BUS

RxTx

LED

DB9 GND

ENABLE

Printers are not supported on the USB

bus.

1- Parallel converter cable box (BlackBox P/N:

PI045A

2- Parallel printer (compatible option bus control

panels only)

5.0 DX4010V2 Jumper Pin

Settings

5.1 Enable LED Jumper Pins (P2)

Use the diagnostic LEDs for troubleshooting. To

enable the LEDs, place a jumper plug across the

jumper pins labeled P2.

Refer to Figure 6 for jumper pin settings.

The DX4010V2 draws more current when

the diagnostic LEDs are enabled. Do not

enable the diagnostic LEDs under normal

operating conditions.

Figure 6: P2 Jumper Settings

3 4

SER

RxTx

BUS

RxTx

LED

DB9 GND

ENABLE

1- DB9 GND enable pins (P1)

2- Diagnostic LED enable pins (P2)

3- Disabled

4- Enabled

Table 2: Diagnostic LED Functions

Diagnostic

LED

Function

BUS RX Data bus receives data from control

panel

BUS TX Data bus transmits data to control

panel

SER RX RS-232 receives data from serial

device

SER TX RS-232 transmits data to serial device

5.2 DB9 Ground Enable Pins (P1)

Some devices connected to the DB9 DTE RS-232

connector (P6) can cause a ground fault condition on

the control panel. If this occurs, removing the plug

across the P1 jumper pins clears the ground fault

condition.

Some devices might still cause a ground

fault even if the P1 jumper plug is

removed.

Refer to Figure 6 for jumper pin settings.

DX4010V2 |Installation Instructions | 6.0 Remote Programming Direct Connection

Bosch Security Systems, Inc. | 9/08 | F01U083036-01 7

5.3 Address DIP Switches

The address DIP switches are used to assign an

address to the DX4010V2.

Refer to Table 3 on page 8 for DIP switch option bus

address settings.

Refer to Table 4 on page 9 for DIP switch SDI bus

address settings.

Refer to Figure 7 for proper DIP switch orientation.

Figure 7: DIP Switch Location and Orientation

123456

12481632

64 128

SER

RxTx

BUS

RxTx

LED

DB9 GND

ENABLE

1- Address DIP switches

2- Address example (option bus Address 0)

3- OFF position

4- ON position

6.0 Remote Programming

Direct Connection

The DX4010V2 can be used to create a local direct

connection for remote programming of a compatible

control panel.

Option Bus: Set the address DIP switches to

Address 0. Refer to Table 3 on page 8.

SDI Bus: Set the address DIP switches to Address

88. Refer to Table 4 on page 9.

Consult your control panel’s installation guide for

specific wiring connections.

A DB9 to DB9 null-modem cable is

required when using the direct

connection method.

DX4010V2 |Installation Instructions | 6.0 Remote Programming Direct Connection

8 Bosch Security Systems, Inc. | 9/08 | F01U083036-01

Table 3: Option Bus Address DIP Switch Settings

Some automation software packages might require that you restart the application if USB

connection is lost during use.

DIP Switch Settings

DIP

Switches

S1 S2 S3 S4 S5 S6 S7 S8

Module

Address

1 2 4 8 16 32

(Mode)

(Option/SDI)

128

(Checksum +1)

0* ON ON ON ON ON OFF ON OFF

1 OFF ON ON ON ON OFF ON OFF

2 ON OFF ON ON ON OFF ON OFF

3 OFF OFF ON ON ON OFF ON OFF

4 ON ON OFF ON ON OFF ON OFF

5 OFF ON OFF ON ON OFF ON OFF

6 ON OFF OFF ON ON OFF ON OFF

7 OFF OFF OFF ON ON OFF ON OFF

8 ON ON ON OFF ON OFF ON OFF

9 OFF ON ON OFF ON OFF ON OFF

10 ON OFF ON OFF ON OFF ON OFF

11 OFF OFF ON OFF ON OFF ON OFF

12 ON ON OFF OFF ON OFF ON OFF

13** OFF ON OFF OFF ON OFF ON OFF

14** ON OFF OFF OFF ON OFF ON OFF

15 OFF OFF OFF OFF ON OFF ON OFF

134 ON ON OFF ON ON ON ON ON

135 OFF ON OFF ON ON ON ON ON

136 ON OFF OFF ON ON ON ON ON

137 OFF OFF OFF ON ON ON ON ON

138 ON ON ON OFF ON ON ON ON

139 OFF ON ON OFF ON ON ON ON

140 ON OFF ON OFF ON ON ON ON

141 OFF OFF ON OFF ON ON ON ON

142 ON ON OFF OFF ON ON ON ON

143 OFF ON OFF OFF ON ON ON ON

144 ON OFF OFF OFF ON ON ON ON

145 OFF OFF OFF OFF ON ON ON ON

250 ON ON ON ON ON ON ON ON

251 OFF ON ON ON ON ON ON ON

252 ON OFF ON ON ON ON ON ON

253 OFF OFF ON ON ON ON ON ON

* Installer’s mode: Use for direct connection of remote programming and diagnostic tools.

** DS7412 emulation

The DS7400Xi (USA) only supports one DX4010V2.

Option bus control panels: D6412, D4412, DS7240, DS7220, DS7400Xi (v2.02 or higher).

DX4010V2 |Installation Instructions | 6.0 Remote Programming Direct Connection

Bosch Security Systems, Inc. | 9/08 | F01U083036-01 9

Table 4: SDI Bus Address DIP Switch Settings

SDI DIP Switch Settings

SDI DIP

Switches

S1 S2 S3 S4 S5 S6 S7 S8

Module

Address

1 2 4 8 16 32

(Mode)

(Option/SDI)

128

(Checksum +1)

80* ON ON ON ON OFF OFF OFF OFF

81 OFF ON ON ON OFF OFF OFF OFF

82 ON OFF ON ON OFF OFF OFF OFF

83 OFF OFF ON ON OFF OFF OFF OFF

84 ON ON OFF ON OFF OFF OFF OFF

85 OFF ON OFF ON OFF OFF OFF OFF

86 ON OFF OFF ON OFF OFF OFF OFF

87 OFF OFF OFF ON OFF OFF OFF OFF

88** ON ON ON OFF OFF OFF OFF OFF

89 OFF ON ON OFF OFF OFF OFF OFF

8A ON OFF ON OFF OFF OFF OFF OFF

8B OFF OFF ON OFF OFF OFF OFF OFF

8C ON ON OFF OFF OFF OFF OFF OFF

8D OFF ON OFF OFF OFF OFF OFF OFF

8E ON OFF OFF OFF OFF OFF OFF OFF

8F OFF OFF OFF OFF OFF OFF OFF OFF

Positions 5, 6, and 8 are not used for SDI bus.

* Used for BIS, PC 9000, and other third party applications.

** Used for RPS and alternate communication.

SDI bus control panels (v6.0 or higher): D9412GV2, D7412GV2, D7212GV2, D9412G, D7412G,

D7212G, D9124, D9112, D7412, and D7212.

DX4010V2 |Installation Instructions | 7.0 DB9 DTE RS-232 Connector (P6)

10 Bosch Security Systems, Inc. | 9/08 | F01U083036-01

7.0 DB9 DTE RS-232

Connector (P6)

The DX4010V2 serial port is wired as a DTE device.

•If the connected device is a data carrier

equipment (DCE) device (most common, such

as an external modem), use a straight through

9-pin to 9-pin, or (DTE to DCE) 9-pin to 25-pin

cable.

•If the connected device is a DTE device (such

as a PC serial port), a null-modem (DTE to

DTE) 9-pin to 9-pin, or null-modem 9-pin to 25-

pin cable is required.

Consult the operating manual provided with your

compatible device for wiring requirements.

If you are using an alternate configuration, you

must make a custom cable (refer to Figure 8 and

Table 5).

Figure 8: DB9 Connector Layout

1 2 3 4 5

6 7 8 9

1- DCD

2- RxD

3- TxD

4- DTR

5- GND

6- DSR

7- RTS

8- CTS

9- RI

Table 5: Alternate Wiring Configuration

DX4010V2

9-Pin DTE

Connector

DCE

(9-pin)

DTE

(9-pin)

DCE

(25-pin)

DTE

(25-pin)

1: DCD

(not used)

1: DCD 1: DCD 8: DCD 8: DCD

2: RxD 2: RxD 3: TxD 3: RxD 2: TxD

3: TxD 3: TxD 2: RxD 2: TxD 3: RxD

4: DTR 4: DTR 6: DSR 20:

DTR

6: DSR

5: GND 5: GND 5: GND 7: GND 7: GND

6: DSR 6: DSR 4: DTR 6: DSR 20: DTR

7: RTS 7: RTS 8: CTS 4: RTS 5: CTS

8: CTS 8: CTS 7: RTS 5: CTS 4: RTS

9: RI

(not used)

9: RI 9: RI 22: RI 22: RI

Inhaltsverzeichnis

Andere Bosch Aufnahmegeräte Handbücher

Bosch

Bosch HPC 410 Bedienungsanleitung

Bosch

Bosch DIVAR IP all-in-one 4000 Bedienungsanleitung

Bosch

Bosch CLIMATE 5000 VRF RDCI Series Bedienungsanleitung

Bosch

Bosch B450-M Bedienungsanleitung

Bosch

Bosch Climate 5000 Series Bedienungsanleitung

Bosch

Bosch DIP-5042EZ-0HD Bedienungsanleitung

Bosch

Bosch FLM-420-O8I2-S Bedienungsanleitung

Bosch

Bosch LBB 1968/00 Bedienungsanleitung

Bosch

Bosch FLM-420-NAC-S Bedienungsanleitung

Bosch

Bosch MSI 60 Bedienungsanleitung

Bosch

Bosch D8125MUX Betriebsanleitung

Bosch

Bosch DIVAR IP all-in-one 6000 Bedienungsanleitung

Bosch

Bosch B450 Betriebsanleitung

Bosch

Bosch DVR1A1081 Bedienungsanleitung

Bosch

Bosch HPC 400 Bedienungsanleitung

Bosch

Bosch FLM-420/4-CON-S Bedienungsanleitung

Bosch

Bosch FLM-420-RHV-S Bedienungsanleitung

Bosch

Bosch Rexroth IMmtcp Bedienungsanleitung

Bosch

Bosch TINYON IP 2000 WI Montageanleitung

Bosch

Bosch M 60 Bedienungsanleitung

Bosch

Bosch D125B Bedienungsanleitung

Bosch

Bosch DCN multimedia Bedienungsanleitung

Bosch

Bosch CR 400 Bedienungsanleitung

Bosch

Bosch Rexroth IMenip2 Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch