Bosch EX49 Bedienungsanleitung

MAN-49-00

Precision Engineered Opto-Electronics™

EX49

“No-Grip” High Impact Dome Camera

INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep this instruction.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install

in accordance with manufacturer instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves or other

apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the third prong is provided for your safety. If

the provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the power where they exit

from the apparatus.

11. Only use attachments/accessories specified by

the manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms

or when unused for long periods of time.

14. Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in a way, such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

IMPORTANT

For best results, please read this Instruction Booklet prior to

installing the EX49 camera.

WARNING !

CSA Certified / UL Listed CLASS 2 power adaptors must be used

in order to comply with electrical safety standards.

This Product Has Been Certified By CSA International To

Include the Health Care Facility Requirements Of UL 2044.

Bosch Security Systems, Inc. will not be responsible for injuries

or damages resulting from the improper installation or use of any

product sold by Bosch Security Systems, Inc their agents,

distributors or dealers.

EU Directives covered by this declaration:

72/9/EC Low Voltage Directives

89/336/EEC Electromagnetic Compatibility Directive

NOTE: This equipment has been tested and found to

comply with the limits for a digital device, pursuant to

part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. As part of its’

normal operation this device can generate radio

frequency energy and if not installed and used in

accordance with the installation manual may cause

interference to radio communications. However, there

is no guarantee that interference will not occur on a

particular installation. If the device does cause

interference to radio or television reception the user is

encouraged to try to correct the interference by one or

more of the following measures:

1) Fit Ferrite beads on all cable to and from the power

supply box, within the box walls.

2) Route the composite cable between the camera and

the power supply in steel conduit piping over the entire

run of the cable up to and including connection to a

deep conduit base fitted under the camera and a conduit

fitting adaptor in the wall of the PSU box.

3) Contact Bosch for further advice.

INDEX – EX49

Page

Description .........................................................1

Unpacking ..........................................................2

Parts List ............................................................2

Items Required for Installation ...........................2

Initial Preparations .............................................3

Guidelines ..........................................................3

Section 1. Dome Removal .................................4

Section 2. Input Power Connections................. 6

Section 3. Mounting – Camera Base .................9

Section 4. Lens: Directional, Focus, and

“Auto-Iris” Adjustments....................14

Section 5. Camera Re-Assembly.....................24

Section 6. Troubleshooting Guide....................26

Section 7. Template – Mounting Holes............29

Section 8. General Specifications....................30

DESCRIPTION

The EX49 “No-Grip” High Impact Dome

Camera for a Vari Focal “Auto-Iris” lens has

been engineered for surveillance in hostile

environments. Compact and good looking, the

camera features a smooth “no-grip” housing for

protection against theft and vandalism.

An aluminum housing, CNC-machined from a

billet, with an impact resistant polycarbonate

dome and locking retaining ring, make it

extremely rugged and weather-tight.

For viewing adjustment, the CCD Camera/Lens

Assembly can be fully rotated using a unique

“Pan-Tilt-Twist” (PTT) mounting bracket.

A voltage regulator circuit allows for 12V dc or

24V ac operation, and a range in between, also

providing protection from voltage surge,

transient spikes, and reverse voltage.

The EX49 is available in several models

designed to meet specific needs.

UNPACKING

Care should be taken when unpacking the shipped

unit. Check the parts list and confirm all items have

been located. Inspect the equipment thoroughly to

ensure nothing was damaged in transit.

Contact BOSCH Service Center if a problem is

noted, see the rear page of this booklet for contact

numbers.

PARTS LIST (items supplied with unit)

- EX49 Camera Assembly with foam gasket

- Installation Instructions booklet

-Plastic bag containing one Allen key

ITEMS REQUIRED FOR INSTALLATION

(not supplied with unit)

- Philips screwdriver

- Small slotted screwdriver

- Mounting screws, etc.

INITIAL PREPARATIONS

Determine the operating voltage at the

installation site. The camera‘s Voltage

Regulator Board accepts either +12V dc or

24V ac input.

See Section 2, Input Power Connections.

Determine the optimum location for the

camera. Section 3, Mounting-Camera Base.

All cameras have been tested prior to

shipment. After the wiring has been

reconnected, it is advisable to check the

camera’s operation before installation.

ESD protection – Cameras and circuit boards

are sensitive electronic components. It is

recommended to wear a ground strap to

ground any static charge. (Alternative: touch a

grounded metal plate for at least a minute

before proceeding with any disassembly)

GUIDELINES

The installation of the EX49 camera is explained in

Sections 1 to 5 listed below. It is important that these

steps are followed in sequence

1. Dome Removal

2. Input Power Connections

3. Mounting – Camera Base

4. Lens Directional and Focus Adjustments

5. Camera Re-Assembly

1. DOME REMOVAL

The camera dome and its retaining ring must be

removed prior to mounting the camera or

adjusting the lens direction.

The set-screws in the retaining ring are not

tightened in the factory and protrude by 1/8"

(3mm) in order for the ring to be rotated.

Refer to Figure 1 - 1 on page 5.

Step 1.1 - Place the camera on a flat surface.

Step 1.2 - Press firmly on the dome with one

hand and rotate the retaining ring in

a counter-clockwise direction with

the other hand. Push against the

protruding set-screws with a finger

to rotate the ring. Do not use a

screwdriver or other metal device.

Step 1.3 - Remove the dome and the retaining

ring. Set them aside.

Andere Handbücher für EX49

Inhaltsverzeichnis

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch VEZ-400 Series Bedienungsanleitung

Bosch

Bosch FCS-8000-VFD-B Bedienungsanleitung

Bosch

Bosch AVIOTEC 8000i IR Leitfaden

Bosch

Bosch VG4-200 Series Bedienungsanleitung

Bosch

Bosch LTC 0465 Series Bedienungsanleitung

Bosch

Bosch AutoDome Junior Bedienungsanleitung

Bosch

Bosch WZ18 Bedienungsanleitung

Bosch

Bosch MIC-7502-Z30B Bedienungsanleitung

Bosch

Bosch AVIOTEC 8000i IR Bedienungsanleitung

Bosch

Bosch EX65 Bedienungsanleitung

Bosch

Bosch AUTODOME IP 4000 HD NEZ-4 series Bedienungsanleitung

Bosch

Bosch FLEXIDOME HD 1080p VR Bedienungsanleitung

Bosch

Bosch AUTODOME IP starlight 5000i Bedienungsanleitung

Bosch

Bosch FLEXIDOME HD Gebrauchsanweisung

Bosch

Bosch UNPMS28 Bedienungsanleitung

Bosch

Bosch 5000 Series Bedienungsanleitung

Bosch

Bosch AutoDome VG5-162-EC0 Bedienungsanleitung

Bosch

Bosch VC973650T Bedienungsanleitung

Bosch

Bosch VEN-650 Series Bedienungsanleitung

Bosch

Bosch VJR-821-ICCV Bedienungsanleitung

Bosch

Bosch VDC-445V03-20S Bedienungsanleitung

Bosch

Bosch VTC-206 Series Bedienungsanleitung

Bosch

Bosch AN bullet 2000 IR Bedienungsanleitung

Bosch

Bosch FLEXIDOME IP 3000i IR Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung