Bosch MIC Series 500 Bedienungsanleitung

MIC Series 500 Camera

MIC Series 500

en Quick Install Guide

MIC Series 500 Camera Table of Contents | en 3

Bosch Security Systems, Inc. User’s Manual F.01U.173.601 | 2.0 | 2010.11

Table of Contents

1 MIC 500 Series Camera Quick Start Guide 4

1.1 MIC 500 Series Camera Mounting Instructions 4

1.2 Safety Earthing of the MIC 500 Series Camera 5

1.3 Commissioning the MIC 500 Series Camera 6

4en | MIC 500 Series Camera Quick Start Guide MIC Series 500 Camera

F.01U.173.601 | 2.0 | 2010.11 User’s Manual Bosch Security Systems, Inc.

1 MIC 500 Series Camera Quick Start Guide

1.1 MIC 500 Series Camera Mounting Instructions

The upright unit can be mounted with the camera ball up or down.

For inverted units, first remove the four M3 x 6 screws fixing the rain shield to the face of the

camera, reverse the rain shield, reattach it to ensure that the rain shield is oriented correctly,

and then configure the camera for inverted operation. For further details of configuring and

reversing the controls for inverted units using the MIC Series Universal Camera Setup

Software (cam-set) or via the MIC 500 Series camera on-screen menu, please refer to the Help

and Instruction file in cam-set.

The MIC 500 Series camera, when canted, is designed only to be mounted ball up. The tilt

limits for the canted unit prevent it from working properly if mounted ball down. Do not

manually back drive the pan or tilt axis by hand. Back driving may strip teeth off the internal

gears and in so doing will void the warranty.

M8 Stainless steel nuts, bolts, and washers should be used to secure the base to the

mounting surface. Suitable sealant or the Nebar gasket may be used between the camera

base and the mounting surface.

Ensure that the 12-pin connector is located inside the camera base plug and that the lock ring

is tightened. Ensure that the base compartment containing the 12-way connector is moisture

proof. On inverted units, it is very important that the connector area is watertight to prevent

water pooling around the connector.

Figure 1.1 MIC 500 Series camera mounting positions: Inverted, Upright, and Canted

CAUTION!

To reduce the risk of electrical shock, disconnect power supply before opening the power

supply unit.

Power disconnect: power supply units have power supplied whenever the power cord is

inserted into the power source.

WARNING!

Installation should be carried out by qualified personnel only in accordance with the

applicable local codes.

Bosch Security Systems Inc. accepts no liability for any damages or losses caused due to

incorrect or improper installation.

MIC Series 500 Camera MIC 500 Series Camera Quick Start Guide | en 5

Bosch Security Systems, Inc. User’s Manual F.01U.173.601 | 2.0 | 2010.11

The MIC 500 Series camera has a security attachment point for attaching to a safety chain

(not supplied), which in turn should be attached to a secure part of the structure during

installation or removal.

1.2 Safety Earthing of the MIC 500 Series Camera

The electronics and housing of the MIC 500 Series camera are electrically isolated; however,

the housing should be safety earthed regardless. This safety earth should be a bonding

connection, such as one of the securing bolts, to the outside case of the camera. The camera

should be earthed at one point only to prevent earth loops and thus hum bars appearing on

the camera picture in the control room.

Shielded Composite Cable Connections

Note: all connections must be made.

Mains Power and Video Connections

WARNING!

Use caution when installing the MIC 500 Series camera. Follow common sense precautions

such as fitting a safety chain.

Composite Cable Wire Color Function MIC PSU Terminal Block PCB Marking

Red AC supply HD3-1 Power

Green AC supply return HD3-2 Power

White RX + Hd3-3 RxB

Yellow Rx - HD3-4 RxA

Drain Wire Ground HD3-5 GND

Blue Tx - HD3-6 TxA

Violet Tx + HD3-7 TxB

Coax Core Video HD3-8 Video

Coax Screen Video return HD3-9 Vid 0V

Black (optional) Tamper switch HD3-10 Tamp Sw

Orange (optional) Wash drive HD3-11 Wash

Brown Heater+ HD6-1

Gray Heater-1HD6-2

1. Please refer to the MIC Series Power Supply Manual for details on connecting MIC 500 Series cameras with

heaters and other auxiliary equipment.

Mains

Live HD1-1

Neutral HD1-2

Earth Connection Already made

Video

Video BNC CN1 Connection

Core Video to Control Room

Screen Video GND to Control Room

6en | MIC 500 Series Camera Quick Start Guide MIC Series 500 Camera

F.01U.173.601 | 2.0 | 2010.11 User’s Manual Bosch Security Systems, Inc.

A standard female BNC connector provides the composite video output from the MIC 500

Series camera.

Telemetry Connections

The MIC 500 Series camera can be daisy-chained in a multi-drop configuration, the last or

furthest camera in the chain should be typically terminated with a 120 Ω resistor placed

across the cameras receiving pair.

1.3 Commissioning the MIC 500 Series Camera

The MIC 500 Series camera provides twin protocol support with a single software pack.

Switching between the installed protocols is easily done using cam-set or the on screen menu

function. Three protocol packs are available: Forward vision (FV)/ Bosch, FV/Pelco and FV/

VCL.

All MIC 500 Series cameras are supplied set to address 1 and initially loaded with the FV /

Bosch protocol pack. The available protocol packs are provided on the CD and can be loaded

onto the camera using cam-set.

To use the MIC Series Universal Camera Setup software (cam-set), connect the MIC 500

Series camera power supply (HD4 or HD5) to a PC using either the MIC-USB485CVTR, an

RS485 to USB signal converter, or for older PCs with a serial port, a suitable RS232 to RS485

converter can be used. Please refer to the Help and Instruction file in cam-set for further

details.

Telemetry

Signal Function Telemetry Signal Name HD4 or HD5

RS485+ to camera RxB Pin 1

RS485– to camera RxA Pin 2

0v from control room GND Pin 3

RS485– to control room TxA Pin 4

RS485+ to control room TxB Pin 5

Bosch Security Systems, Inc.

Robert-Koch-Straße 100

D-85521 Ottobrunn

Germany

Phone +49 89 6290-0

Fax +49 89 6290-1020

www.boschsecurity.com

Andere Handbücher für MIC Series 500

Inhaltsverzeichnis

Andere Bosch Sicherheitskamera Handbücher

Bosch

Bosch FLEXIDOME corner 9000 MP Montageanleitung

Bosch

Bosch NUC-50022-F2M Bedienungsanleitung

Bosch

Bosch MIC Series 400 Bedienungsanleitung

Bosch

Bosch AUTODOME IP starlight 5100i Bedienungsanleitung

Bosch

Bosch AN traffic 4000 IR Bedienungsanleitung

Bosch

Bosch AutoDome Junior HD Fixed Camera Bedienungsanleitung

Bosch

Bosch SVI-1609-5 Montageanleitung

Bosch

Bosch NBN-80052 Bedienungsanleitung

Bosch

Bosch WZ20NXV550-0 Bedienungsanleitung

Bosch

Bosch AUTODOME IP starlight 5000i Bedienungsanleitung

Bosch

Bosch FLEXIDOME HD 1080p VR Bedienungsanleitung

Bosch

Bosch LTC-0455-61 Bedienungsanleitung

Bosch

Bosch DINION IP 7000 HD NBN-71022 Bedienungsanleitung

Bosch

Bosch FlexiDomeXF VDC-485V03-10 Bedienungsanleitung

Bosch

Bosch MIC-7502-Z30B Bedienungsanleitung

Bosch

Bosch AUTODOME IP 5000 HD NEZ-5 Series Bedienungsanleitung

Bosch

Bosch MIC Series 440 Installationsanleitung

Bosch

Bosch VDN-498V03-11 Bedienungsanleitung

Bosch

Bosch NDP-5512-Z30C Bedienungsanleitung

Bosch

Bosch VG4-322-CTS Bedienungsanleitung

Bosch

Bosch EX30-IP Bedienungsanleitung

Bosch

Bosch EXTEGRA IP 9000 FX NXF-9x30 Bedienungsanleitung

Bosch

Bosch KBE-335V28-20 Bedienungsanleitung

Bosch

Bosch MIC-7522 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung